Siemens Moore 353 User Manual page 67

UM353-1
3.2.28 COS_ - COSINE
COS_ function blocks, in firmware 1.30 and higher, accept radian
inputs and output the cosine of that angle.
X
. Input X
3.2.29 CWE_ - Coil Write Ethernet (V3.0)
CWE_ function blocks are available when the
optional Ethernet communication board
installed in the controller. It enables the controller
to write Coil data to other stations over the
Ethernet network.
Up to 32 CWE_ blocks are available. Blocks are
assigned in sequence, controller wide, with each
use. Up to 16 ON/OFF block inputs, I0 to IF, can
write to 16 consecutive coil locations in a
destination Modbus device.
The IP ADRES parameter is used to configure the
IP address of the destination Modbus device.
The MB ADRES parameter allows a Modbus
address to be configured. When connecting to
other Siemens MOORE controllers, the Modbus
address is set to 1. In some cases, other Modbus
devices may use a different address or when
going through a Modbus TCP/IP gateway a
Modbus network may have multiple devices, each
having a unique address.
The START CL parameter identifies the location
of the first Coil. The NO OF CL parameter
identifies the total number of coils, up to 16, to
write.
There are three write update options that can be configured by the UD TYPE parameter.
9
Requires Ethernet communications board firmware version 2.0 or later
March 2003
COS (X) O1
Output 1
BLOCK DIAGRAM
9
is
I P
M B
S T A R
N O
U
COSINE
COS
X
Input X
.
I N P U T X
INPUT X ..............
E S N
Exec. Seq. No. ..................... 000 to 250
COIL WRITE - ETHERNET
CWE_
Input 0 0
COIL WRITE
Input F F
ETHERNET
Input T T
QS
Quality Status
I N P U T 0
INPUT 0 ............... loop tag.block tag.output
(H)
I N P U T 1
INPUT 1 ............... loop tag.block tag.output
(H)
I N P U T 2
INPUT 2 ............... loop tag.block tag.output
(H)
I N P U T 3
INPUT 3 ............... loop tag.block tag.output
(H)
I N P U T 4
INPUT 4 ............... loop tag.block tag.output
(H)
I N P U T 5
INPUT 5 ............... loop tag.block tag.output
(H)
I N P U T 6
INPUT 6 ............... loop tag.block tag.output
(H)
I N P U T 7
INPUT 7 ............... loop tag.block tag.output
(H)
I N P U T 8
INPUT 8 ............... loop tag.block tag.output
(H)
I N P U T 9
INPUT 9 ............... loop tag.block tag.output
(H)
I N P U T A
INPUT A ............... loop tag.block tag.output
(H)
I N P U T B
INPUT B ............... loop tag.block tag.output
(H)
I N P U T C
INPUT C ............... loop tag.block tag.output
(H)
I N P U T D
INPUT D ............... loop tag.block tag.output
(H)
I N P U T E
INPUT E ............... loop tag.block tag.output
(H)
I N P U T F
INPUT F ............... loop tag.block tag.output
(H)
I N P U T T
INPUT T ............... loop tag.block tag.output
(H)
A D R E S
IP A DdRESs ..........................
(H)
A D R E S
MB A DdRES s
(H)
T C L
START ing CoiL
(H)
O F C L
NO. OF C oiLs
(H)
D T Y P E
UpDate TYPE
(H)
Function Blocks
ESN = 000
O1 Output 1
O = COS (X)
1
loop tag.block tag.output (null)
(000)
(null)
(null)
(null)
(null)
(null)
(null)
(null)
(null)
(null)
(null)
(null)
(null)
(null)
(null)
(null)
(null)
(null)
nnn.nnn.nnn.nn n
(192.168.0.0)
................................... 0 - 255
(0)
...................... 0000 - 65535
(0)
..................................... 1 - 16
(1)
......................... oncE/P2P/Ct
(oncE)
3-37