Trane BCI-I Integration Manual page 32

Table 8. Binary Output
Object Identifier
Binary Output, 15
Binary Output, 16
Table 9. Binary Input
Object Identifier
Binary Input, 1
Binary Input, 2
Binary Input, 3
Binary Input, 9
Binary Input, 10
Binary Input, 11
Binary Input, 15
Binary Input, 22
Binary Input, 23
Binary Input, 24
Binary Input, 25
Binary Input, 26
Binary Input, 27
Binary Input, 28
Binary Input, 161
Binary Input, 162
Binary Input, 163
Binary Input, 164
Binary Input, 165
Binary Input, 166
Binary Input, 243
Table 10. Diagnostics, Binary Input
(a)
Object Identifier
Binary Input, 29
Binary Input, 30
Binary Input, 31
(use Object
Identifier for RT or CSC)
Binary Input, 31
(use Object
Identifier for FAU)
ACC-SVP01B-EN • BCI-I Integration Guide
Object Name
Dehumidification Command
Humidification Command
Object Name
System Control Status
Compressor Lockout Status
Unit Status
VAV Box Command
Demand Limit Status
Service Test Mode Status
Supply Fan Configuration Status
Economizer Airside Enable Status
Waterside Economizer Enable Status
Condenser Water Pump Status
Condenser Water Flow Status
Energy Recovery Frost Avoidance Status
Energy Recovery Status
Energy Recovery Preheat Status
Evaporator Frost Protection Circuit 1
Status
Evaporator Frost Protection Circuit 2
Status
Evaporator Frost Protection Circuit 3
Status
Evaporator Frost Protection Circuit 4
Status
Alarm Relay Output Status
Diagnostic Stop Status
Condenser Water Drain Status
Object Name
Diagnostic: RTM Zone Temp Sensor Failure
Diagnostic: Supply Air Temp Sensor Fail
Diagnostic: RTM Aux Temp Sensor Failure
Diagnostic: SA Temp Sensor Fail
Object Data Points and Diagnostic Data Points
Description
Command the operating state of
the dehumidification system.
Command the operating state of
the humidification system.
Description
Indicates the control system currently in
command of the unit.
One or more compressors are locked out with
no diagnostic.
Indicates the current state of the unit.
Indicates whether VAV boxes should be in
control or wide open.
Indicates if the unit is in an energy-demand
limit mode
Indicates if the unit is in service test mode.
Indicates the supply fan configuration.
Indicates the status of the airside economizer
system.
Indicates the status of the waterside
economizer system.
Indicates the status of the condenser water
system pump.
Indicates the flow status of water in the
condenser system.
Status of the energy recovery system frost
protection function.
Indicates the status of the energy recover
system.
Indicates the status of the energy recovery
preheat function.
The status of evaporator frost protection
function for circuit 1.
The status of evaporator frost protection
function for circuit 2.
The status of evaporator frost protection
function for circuit 3.
The status of evaporator frost protection
function for circuit 4.
Indicates the state of the alarm relay on the
unit.
Indicates if the unit diagnostic has caused the
unit to shutdown.
Indicates the status of the condenser water
drain
Description
Diagnostic: RTM Zone Temp Sensor Failure
Diagnostic: Supply Air Temp Sensor Fail
Diagnostic: RTM Aux Temp Sensor Failure
Diagnostic: SA Temp Sensor Fail
Relinquish
Default Object States
Inactive = Disabled
Active
Active = Auto
Inactive = Disabled
Active
Active = Auto
Object States
Inactive = Standalone control
Active = BAS control
Inactive = Normal
Active = Locked Out
Inactive = Off
Active = On
Inactive = Auto
Active = Open
Inactive = Inactive
Active = Active
Inactive = Inactive
Active = Active
Inactive = Cycling
Active = Continuous
Inactive = Disabled
Active = Enabled
Inactive = Disabled
Active = Enabled
Inactive = Inactive
Active = Active
Inactive = No Flow
Active = Flow
Inactive = Inactive
Active = Active
Inactive = Inactive
Active = Active
Inactive = Inactive
Active = Active
Inactive = Inactive
Active = Active
Inactive = Inactive
Active = Active
Inactive = Inactive
Active = Active
Inactive = Inactive
Active = Active
Inactive = De-energized
Active = Energized
Inactive = Inactive
Active = Active
Inactive = Closed
Active = Open
31