Advertisement
Quick Links
LED Light Kit
Serial Number 400000000 and After Greensmaster
1600, Flex
Model No. 04063
Model No. 04064
WARNING
CALIFORNIA
Proposition 65 Warning
This product contains a chemical
or chemicals known to the State of
California to cause cancer, birth defects,
or reproductive harm.
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
7
8
© 2017—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
™
1820/2120, and eFlex
Description
No parts required
No parts required
LED light assembly
Light mount
Flange-head bolt (3/8 inch)
Flange nut (3/8 inch)
LED light assembly
Light mount
Mount plate
Flange-head bolt (3/8 inch)
Flange-head bolt (5/16 x 1 inch)
Flange-head bolt (5/16 x 1-1/2 inches)
Flange locknut (5/16 inch)
Flange nut (3/8 inch)
Flange nut (5/16 inch)
Washer
Wire harness
2-position rocker switch
Cable tie
No parts required
Register at www.Toro.com.
®
1820/2120 Series Mower
Use the appropriate model for your machine as
follows:
•
Model No. 04063—Greensmaster
and 1600 series machines
•
Model No. 04064—Greensmaster
1820/2120 or eFlex 1820/2120 series machines
Note:
Determine the left, right, front, and back sides
of the machine from the normal operating position.
Qty.
–
Prepare the machine.
Remove the control-panel cover (1820
–
or 2120 series machines).
2
2
Assemble the light mounts to the 800,
1000, and 1600 series machine.
4
2
2
2
1
1
1
Assemble the light mounts to the 1820
or 2120 series machine.
4
4
1
1
4
Assemble the wire harnesses to the
2
machine.
1
Install the light switch.
10
Install the cable ties.
–
Finish the light kit installation.
Original Instructions (EN)
All Rights Reserved *3415-336* A
Printed in the USA
Form No. 3415-336 Rev A
®
800, 1000,
Installation Instructions
®
800, 1000,
®
Flex
Use
Advertisement
Related Manuals for Toro 04063
Summary of Contents for Toro 04063
- Page 1 Serial Number 400000000 and After Greensmaster ® 800, 1000, 1600, Flex ™ 1820/2120, and eFlex ® 1820/2120 Series Mower Model No. 04063 Model No. 04064 Installation Instructions Use the appropriate model for your machine as WARNING follows: CALIFORNIA • Model No. 04063—Greensmaster ®...
-
Page 2: Preparing The Machine
2. Move the machine to a level surface and set the traction and reel drive engagement lever to the N position; refer to the Operator’s EUTRAL Manual. Preparing the Machine 3. Set the throttle control to the S position and push the On-Off switch to the O position;... - Page 3 Removing the Assembling the Light Control-Panel Cover Mounts to the 800, 1000, and 1600 Series Machine 1820 or 2120 Series Machines Parts needed for this procedure: No Parts Required LED light assembly Procedure Light mount 1. Remove the 4 flange-head screws (1/4 x 1/2 Flange-head bolt (3/8 inch) inch) that secure the control-panel cover to the Flange nut (3/8 inch)
- Page 4 g200656 Figure 7 g207878 Figure 5 1. LED light 3. Washer 2. Light mount 4. Nut 1. Bolt—loosen 3. Use 4 flange-head bolts (3/8 inch) and 2 flange nuts (3/8 inch) to secure the light mounts to both side plates (Figure Note: Ensue that the throttle cable is routed...
- Page 5 • Flex/eFlex 1820 machines: position the mount plate to the outside of the left side plate (Figure • Flex/eFlex 2120 machines: position the mount plate to the inside of the left side plate (Figure g200371 Figure 9 Flex/eFlex 2120 Machine Shown 1.
- Page 6 g206120 Figure 10 g206121 Figure 11 Flex/eFlex 2120 Machine Shown 1. Flange-head bolt (5/16 x 4. Light mount 1. Light mount 4. Flange nut (5/16 inch) 1-1/2 inch) 2. Washer 5. Flange locknut (5/16 inch) 2. Flange-head bolt (5/16 x 5.
- Page 7 Assembling the Wire Harnesses to the Machine Parts needed for this procedure: Wire harness Attaching the Wire Harnesses to the LED Lights 1. Connect the 2-pin connector of the LED light into g210745 the 2-socket connector of the LED light harness Figure 14 (Figure 13).
- Page 8 Connecting the LED Light Wire Harnesses to the Machine Wire Harness 800, 1000, and 1600 Series Machines Note: Perform the following steps for the LED light wire harnesses on both sides of the machine. 1. At the back of the console, remove the plug from the 2-socket connector of the machine wire harness (Figure...
- Page 9 Connecting the LED Light Wire Harnesses to the Machine Wire Harness Flex 1820 and 2120 Series Machines Note: Perform the following steps for the LED light wire harnesses on both sides of the machine. 1. At the front of the console, remove the plug from the 2-socket connector of the machine wire g210792 harness...
- Page 10 Connecting the LED Light Wire Harnesses to the Machine Wire Harness eFlex 1820 and 2120 Series Machines Note: Perform the following steps for the LED light wire harnesses on both sides of the machine. 1. At the front of the console, remove the plug from the 2-socket connector of the machine wire g210792 harness...
- Page 11 Ensure that the connectors are fully seated and the latch of the connectors snap together securely. 5. Align the switch so that the notch in the switch Installing the Light Switch body is toward the left side of the control panel (Figure 23).
- Page 12 Installing the Light Switch (eFlex/Flex 1820 and 2120 Series Machines) 1. Remove the plug from the opening at the left face of the control panel (Figure 24 Figure 25). g208352 Figure 25 Flex 1820/2120 Machine Shown 1. Plug 3. 2-position rocker switch 2.
- Page 13 Installing the Cable Ties Parts needed for this procedure: Cable tie Procedure Important: As you install the cable ties, ensure that the wire harnesses have enough slack to prevent stress points and are free from any moving parts 1. Use 8 cable ties to secure the wire harnesses to the machine (Figure 27).
- Page 14 Finishing the Light Kit Installation No Parts Required g032885 Installing the Control-Panel Cover Figure 28 Left side of the machine shown 1820 or 2120 Series Machines 1. Align the keyhole slot in the control-panel cover 1. Wire harness (machine) 3. Wire harness (LED light kit) over the traction and reel drive handle (Figure...
-
Page 15: Operation
Connecting the Spark-Plug Wire Operation 800, 1000, 1600, and Flex 1820 and 2120 Series Machines Operating the Light Switch Connect the spark-plug wire to the terminal of the Press the rocker switch to turn the LED lights to the spark plug; refer to Figure 1 Disconnecting the or O...