Installation & Regulation Guide For Water Flow Switch - Midea Aqua Tempo Super Series Technical & Service Manual

Aqua Tempo Super Series air cooled scroll chiller unit (50Hz)
Fouling phenomena are common and diverse, ranging from fouling of ship hulls, natural surfaces in the
marine environment (marine fouling), fouling of heat-transfer components through ingredients contained in
the cooling water or gases, and even the development of plaque or calculus on teeth, or deposits on solar
panels on Mars, among other examples.
Foreign matter in the chilled water system will adversely affect the heat transfer capability of the evaporator,
and could increase the pressure drop and reduce the water flow. To provide optimum unit operation, proper
water treatment must be maintained. Refer to the able as following.
Fouling Factor
Difference of water
ALTITUDE
inlet and outlet temp.
(m)
(℃)
3
4
Sea level
5
6
3
4
600
5
6
3
4
1200
5
6
3
4
1800
5
6
C--Cooling capacity
P--Power
13.2.5 Installation & regulation guide for water flow switch
● Please carefully check flow switches before conducting installation of the water flow switch. Packing
should be in good condition, and the appearance should be free of damage and deformation. If any problem,
please contact the manufacturer.
● Flow switches can be installed in the horizontal pipeline or the vertical pipeline with upward flowing
direction but cannot be mounted in the pipeline with downward flowing direction. The inlet water of gravity
should be taken into account when flow switches are installed in the pipeline with upward flowing direction.
● Water flow switch must be installed on a section of straight-line pipeline, and its both ends must be
supplied with straight-line pipes whose length is at least 5 times diameter of the pipe. In the meanwhile, the
fluid flowing direction in the pipeline must be consistent with the direction of arrow on the controller. The
connection terminal should be located where wiring connection can be easily done.
● Pay attention to the following items when conducting installation and wire connection:
a. Collision of the wrench with the soleplate of the flow switch is prohibited, since such collision may cause
deformation and failure of the flow switch.
·℃/kW
0.018 m 0.044 m
2
C P C
1.036 1.077 1.019
1.039 1.101 1.022
1.045 1.105 1.028
1.051 1.109 1.034
1.024 1.087 1.008
1.027 1.111 1.011
1.034 1.115 1.017
1.043 1.115 1.026
1.013 1.117 0.996
1.015 1.118 0.998
1.023 1.122 1.006
1.031 1.125 1.015
1.002 1.128 0.986
1.005 1.129 0.989
1.012 1.132 0.995
1.018 1.134 1.001
95
Fouling Factor
·℃/kW ·℃/kW
0.086 m
2 2
P C
1.076 0.991
1.080 0.994
1.086 1.000
1.093 1.006
1.064 0.980
1.068 0.983
1.074 0.989
1.084 0.998
1.052 0.969
1.055 0.971
1.063 0.979
1.072 0.987
1.042 0.959
1.045 0.962
1.051 0.968
1.058 0.974
MCAC-ATSM-201606
·℃/kW
0.172 m
2
P C P
0.975 0.963 0.983
0.996 0.971 0.984
1.000 0.977 0.989
1.004 0.983 0.994
0.984 0.951 0.991
1.005 0.959 0.992
1.009 0.965 0.997
1.009 0.973 0.999
1.011 0.942 1.002
1.012 0.948 1.003
1.015 0.955 1.005
1.018 0.962 1.007
1.021 0.935 1.007
1.022 0.941 1.010
1.024 0.945 1.012
1.026 0.949 1.014