Backup Telephone Programming - NAPCO GEM-P800 Installation Instructions Manual

WI850D GEM-P800 Installation Instructions
to disable reporting to Telco 1.
[0] Disabled [4] Universal High Speed
[1] Ademco Slow [5] Reserved
[2] Radionics Slow [6] Point ID
[3] Silent Knight Fast [7] Pager
[33] Receiver Options
(1) 2300 Hz HS / Kissoff - Select 2300 Hz
Handshake and Kissoff.
(2) Sumcheck - Only used for the follow-
ing Receiver Formats: Ademco Slow, Radi-
onics Fast, Silent Knight Fast and Universal
High Speed. This is a sophisticated data
format used to enhance the speed and
check the accuracy of the received trans-
mission. This format should be used when-
ever the central station has this capability.
Instead of sending a second round to verify
correct data, the panel sends a Sumcheck
digit after sending the Subscriber ID and
Alarm Code.
(3) Single Digit - 3/1 Format. 3-digit Sub-
scriber ID number and a 1-digit Alarm Code
will be transmitted.
(4) No Handshake - (All receiver formats
except Pager Format)
If programmed no Handshake / Kissoff is
required by the panel.
[34] Zone Report, Telco 1
Select zone(s) required to send an alarm
report to Telephone Number 1.
[35] Zone Restore Report, Telco 1
16
Select zone(s) required to send a restore
report to Telephone Number 1. The zones
will send a restore after Bell time-out, unless
programmed as silent zones.
[36] System Reporting, Telco 1
(1) Keypad Fire - Program to activate a
Keypad Fire report (
7G
(2) AUX/AMBUSH - Program to activate
an AUX or AMBUSH report (
(3) Panic - Program to activate a Panic
report ( ).
9G
(4) Test Timer - Program to activate a
Test Timer report.
[37] System Reporting, Telco 1
(1) AC Fail Report - Program to activate
an AC Fail report (15 minute fixed report
delay).
(2) Low Battery Report - Program to acti-
vate a Low Battery report.
(3) *Trouble Report - Program to activate
a Trouble report.
(4) Fire Report - Program to activate a
Fire report.
*Includes Bell Cut, Fire Trouble, Receiver
Fail-to-Respond, Receiver Tamper, Re-
ceiver JAM, Wireless Smoke Low Battery,
Wireless Smoke Supervisory Fail. Point ID
format will report trouble(s) by device and ID
number.
[38] System Restore Report, Telco 1
(1) AC Restore - Program to activate an
AC Restore report.
(2) Battery Restore - Program to activate
a Battery Restore report.
(3) Trouble Restore - Program to activate
a Trouble Restore report.
(4) Fire Restore - Program to activate a
Fire Restore report.
).
[39] Opening/Closing Report, Telco 1
).
8G
Select users required to send opening and
closing reports to Telephone Number 1.
Do not program for users that are intended
to send an Opening After Alarm (Cancel
Code) or Conditional Closing reports.

Backup Telephone Programming

[40] Subscriber ID Number (Telco 2)
For 4/2 format enter a 4 digit number. If 3/1
format is required enter a 3 digit number
then press the
[41] Telephone Number 2
Program the phone number to be dialed for
Telephone Number 2. A fixed dial tone de-
tection (E) is included prior to the Dialing
Prefix [44]. Dial tone detection can be dis-
abled by programming No Dial Tone Detec-
tion [46-1]. To program any additional delay
enter a "D" where required in the phone
number.
key.
F