Table of Contents
Advertisement
System Troubles
Use the System Trouble chart on the following
page to determine the specific System Trouble
(s).
During normal panel operation the
TROUBLE LED has the following two modes of
operation:
STEADY
1-7 possible trouble
groups, AC is present
FLASHING
1-7 possible trouble
groups, AC is not present
Viewing System Trouble(s)
Press the
key on the keypad.
A4
To determine the System Trouble Group Num-
ber, count the number of times the
TROUBLE LED blinks. The keypad sounder will
beep at the same rate that the
TROUBLE LED blinks.
To determine the System Trouble, note the
zone LED that is ON. Look up the specific sys-
tem trouble on the chart on the following page.
The
SYSTEM TROUBLE LED and keypad
H
sounder will continue to flash and beep. To view
the next System Trouble, if any, press the
key. Continue pressing the
E
no more system troubles to view, the system will
return to normal operation.
-
EXAMPLE
Enter
A4
SYSTEM
H
and determine the specific trouble. Press any key to
view all system troubles.
G E M I N I
H
Flashing
(System Trouble
Group Number)
Beeping
(System Trouble
Group Number)
SYSTEM
H
Zone LED(s)
indicates
SYSTEM
H
(Specific Trouble)
FIGURE
9 S
Note: System Troubles Groups 3 through 7 -
System Trouble Groups that have a zone or
smoke detector associated with the trouble,
E
such as RF low battery. The zone(s) of the de-
key, if there are
vice with a low battery will be displayed by the
LOW BATTERY SYSTEM TROUBLE DIS-
PLAY
to enter System Trouble mode
2
System Trouble
Group #
Keypad
SYSTEM
Trouble
LED
is
flashing
1
time
indicating
System
Trouble
Group 1.
Keypad Sounder beeps 1
time
indicating
System
is ON
Specific Trouble
Zone 2 LED is ON indicating
Low Battery. (1 Beep, LED 2)
T
E
YSTEM
ROUBLE
XAMPLE
ZONE LED . For example, a wireless low battery
on zone 2 would beep the keypad sounder 3
times and turn on zone 2 LED.
Audible System Trouble Indication - For all
system troubles, except when the only system
trouble is the loss of AC, the keypad will beep
once every 10 seconds. The keypad will con-
tinue to beep until the reset button is pressed or
the trouble has been acknowledged by pressing
the
key.
C
System Trouble Reporting
The following system troubles, when enabled to
report to Telco 1 [37-3] or Telco 3 [57-3], will
send the report code programmed in Trouble
Report [63] if reporting using a pulse format:
System Trouble
Pulse Report Code
Bell Cut
F1
2-Wire Fire Trouble
F1
Rcvr Fail-to-Respond
F1
Receiver Tamper
F1
Receiver JAM
F1
Tx Low Battery
F1
Tx Supervisory Failure
F1
If reporting using Point ID, a unique code will be
sent for each of the following System Troubles.
System Trouble
Point ID Report Codes
Bell Cut
CODE 1 321 G00 ZN000-BELL 1 TROUBLE
2-Wire Fire Trouble
CODE 1 373 G00 ZN000-FIRE LOOP TRBLE
Rcvr Fail-to-Respond
CODE 1 382 G00 ZN000-SENSOR TROUBLE
Receiver Tamper
CODE 1 145 G00 ZN000-EXP. MODL. TAMPER
Receiver JAM
CODE 1 373 G00 ZN000-FIRE LOOP TRBLE
A 300 (SYSTEM TROUBLE RST) code is sent if a restore is
reported after multiple troubles.
23
Advertisement
Table of Contents
