Table of Contents
Advertisement
PowerBoot
PPC/CPCI-690
4. Enter netload command to load image into DRAM memory
PowerBoot> netload this-is-my-file-name 100000
PHY-Device at 100MB/s and full duplex negotiated
WANCDM MAC ADDRESS : 00:80:42:11:6A:C3
Transmitting RARP-REQUEST... Reception of RARP-REPLY
Transmitting TFTP-REQUEST to server 02:80:42:0A:0D:79, IP
192.168.41.1
PACKET:307 - loaded $00100000..$001265CF (157136 bytes)
PowerBoot> _
5. Enter bf command if you want to change the image
The word "FORCE" is loaded into the user flash:
PowerBoot> bf 100000 500000 "FORCE " p
6. Enter md command to verify DRAM memory contents
PowerBoot> md 100000
00100000:
46 4f 52 43 45 20 46 4f
00100010:
45 20 46 4f 52 43 45 20
00100020:
52 43 45 20 46 4f 52 43
00100030:
46 4f 52 43 45 20 46 4f
00100040:
45 20 46 4f 52 43 45 20
00100050:
52 43 45 20 46 4f 52 43
00100060:
46 4f 52 43 45 20 46 4f
00100070:
45 20 46 4f 52 43 45 20
00100080:
52 43 45 20 46 4f 52 43
00100090:
46 4f 52 43 45 20 46 4f
001000a0:
45 20 46 4f 52 43 45 20
001000b0:
52 43 45 20 46 4f 52 43
001000c0:
46 4f 52 43 45 20 46 4f
001000d0:
45 20 46 4f 52 43 45 20
001000e0:
52 43 45 20 46 4f 52 43
001000f0:
46 4f 52 43 45 20 46 4f
More (cr) ? .
PowerBoot>
7. Enter fprog command to program image from DRAM memory
into user flash
The DRAM memory contents from 100000
grammed.
PowerBoot> fprog user_flash 100000
Programming flash memory
0 ... 100%
0 ... 100%
0 ... 100%
0 ... 100%
Done.
Booting the Board
52 43 45 20 46 4f 52 43
46 4f 52 43 45 20 46 4f
45 20 46 4f 52 43 45 20
52 43 45 20 46 4f 52 43
46 4f 52 43 45 20 46 4f
45 20 46 4f 52 43 45 20
52 43 45 20 46 4f 52 43
46 4f 52 43 45 20 46 4f
45 20 46 4f 52 43 45 20
52 43 45 20 46 4f 52 43
46 4f 52 43 45 20 46 4f
45 20 46 4f 52 43 45 20
52 43 45 20 46 4f 52 43
46 4f 52 43 45 20 46 4f
45 20 46 4f 52 43 45 20
52 43 45 20 46 4f 52 43
..20FFFFF
will be pro-
16
16
4 - 9
Advertisement
Table of Contents
