Effects - Technics SX-PR54/M Operating Instructions Manual

Part I

Effects

DIGITAL EFFECT
DIGITAL EFFECT gives the sound richness and
enhances your performance.
1.
In the CONDUCTOR or PART SELECT sec-
tion, turn on the part to which this effect will be
applied.
2.
Press the DIGITAL EFFECT button to turn it
on.
DIGITAL
EFFECT
• The on or off status of the DIGITAL EFFECT is preset for
each sound.
• This effect does not work for the sounds in the DRUM
KITS sound groups.
• This effect may not work for some sounds.
MULTI EFFECT
The MULTI EFFECT works like a studio effects
processor, providing effects such as CHORUS,
PHASER, DELAY and DISTORTION.
1.
In the CONDUCTOR or PART SELECT sec-
tion, turn on the part to which this effect will be
applied.
2.
Press the MULTI EFFECT button to turn it on.
MULTI
EFFECT
Type and parameter settings
1.
Press and hold the MULTI EFFECT button for
a few seconds.
• The display changes to the following.
Use the L and M buttons to select an effect
2.
group.
• The EFFECT MEMORY is for edited effects (see below).
FADE RHYTHM GROUP
AUTO PLAY CHORD APC/SEQUENCER TEMPO / PROGRAM
VOLUME
SPLIT ONE TOUCH SOUND FUNK & BALLROOM
MAIN POINT MODE OFF/ON PLAY IN OUT ARRANGER METRONOME POP ROCK SOUL DISCO POP BALLAD BALLAD & SHOW
VOLUME
MAX
MAX
SET
CHORD FINDER
PROGRESSIVE WALTZ JAZZ & LATIN &
PIANIST PIANO STYLIST 8 BEAT 16 BEAT USA & TRAD SWING WORLD MEMORY
CONTRAST
OFF
MIN
LOAD
1 2 3 4 1 2 1 2 1 2 3 4 BEAT
DEMO MUSIC STYLE ARRANGER VARIATION FILL IN INTRO & ENDING SYNCHRO & BREAK START / STOP TAP TEMPO - TRANSPOSE + HELP OTHER PARTS/TR
MUTE
SEQUENCER COUNT
RESET INTRO
3.
Use the buttons to the right of the display to
select the type.
• If the types comprise more than one display "page," use
the PAGE buttons to switch pages.
• Press the VARI button to enable the variation effect.
• This display can also be accessed from the REVERB &
EFFECT MENU display. (Refer to page 108.)
EFFECT EDIT
The effects can be edited and then stored in a
memory.
1.
Select an effect type to use as a base.
2.
Press the EFFECT EDIT button.
• The display changes to the following.
Use the PARAMETER L and M buttons to
3.
select the parameter.
∧
4.
Use the VALUE
setting.
• The parameters vary depending on the effect type
selected as the base.
• (V) is the abbreviation of VARIATION.
5.
Press the WRITE button.
6.
Press the EFFECT NAMING button and
assign a name to the effect, if necessary.
• Refer to page 52 for details about the NAMING proce-
dure.
Use the EFFECT MEMORY L and M buttons
7.
to specify the location in which to store the
edited effect.
8.
Press the OK button.
Sounds and effects
SOUND GROUP SEQUENCER
GUITAR & SAX & ORGAN & SOUND EASY PROGRAM DISK
STRINGS VOCAL HARPSI BRASS WOODWIND ACCORDION SYNTH EXPLORER PLAY REC FAVORITES MENUS DISK IN USE
CHORD STEP REC LOAD
MALLET & PIANO ORCH DIGITAL CONDUCTOR DIGITAL MULTI
BASS ORCH PERC WORLD MIXTURES MIXTURES DRAWBARS DRUM KITS MEMORY LEFT RIGHT 2 RIGHT 1 EFFECT EFFECT CHORUS REVERB
P.MEM 5-8
C
A B
DISPLAY HOLD EXIT GRAND UPRIGHT ELECTRIC MODERN SIMPLE PIANO TECHNI-CHORD BANK SET 1 / 5 2 / 6 3 / 7 4 / 8
PAGE
PANEL MEMORY
PIANO
∨
and buttons to adjust the
37
QQTG0701