Table of Contents
Advertisement
E
SET
Parameter
Value
EXT,
PC,
POS
TRACK1–8,
MIXOUT
1/1, 1/2, 1/3, 1/4,
1/5, 1/6, 1/7, 1/8,
SPLIT
1/9, 1/10, 1/11,
1/12, 1/13, 1/14,
1/15, 1/16
LOOP-HOLD
OFF, ON
1/8, 1/16, 1/32,
SCALE
1/4T, 1/8T, 1/16T
LENGTH
1–16
MEASURE
1–8
Detailed Editing
You can edit the effect individually for each pad and step.
1 .
Hold down the
[SHIFT] button
[SCATTER]
button .
The SCATTER menu appears.
2 .
Press the
[ENTER] button
edit .
* Step cannot be edited if pads are assigned to steps.
* When you edit a step, the step is lit red.
Editing a step/pad
You can use the [C1]–[C4] knobs to edit the parameters shown in
the screen.
SETTING
Parameter
Value
COLOR
*1
Default,
SEQ
1–16
MASK
OFF, ON
Explanation
Selects the position at which Scatter is
inserted.
EXT:
Input from the EXT IN jacks
PC:
Input from the USB PC-IN port
TRACK 1-8:
Output of tracks 1–8
MIXOUT:
Before the compressor
Specifies the width of the divisions when
dividing the clip.
For example,
if
1/16,
16, and
SCALE:
LENGTH:
MEASURE:
SPLIT: 1/16 0sixteenth notes
SPLIT: 1/12 0eighth note triplets
0eighth notes
SPLIT: 1/8
* Step numbers beyond the number of divisions
specified by SPLIT are ignored.
This lets you loop the playback while
holding the audio that is loaded into Scatter.
If you change the tempo, the playback
speed and pitch will change simultaneously.
Specifies the beat that is the basis of the
measure.
Specifies the basic number of beats (SCALE)
in a measure.
Specifies the number of measures used by
Scatter.
and press the
PAD MODE
to select the item that you want to
Explanation
Specifies the pad color.
* This setting is only for PAD.
Specifies the timing of playback.
* This setting is only for STEP.
Specifies whether playback of another step
will overlap during playback.
If you raise Size or Hold to extend the
playback time of the step, and do not want
it to overlap the playback of another step,
you can turn this ON so that the step whose
timing overlaps is muted.
However, the step for which this is turned
ON is not muted.
*1 ORANGE, YELLOW, GREEN, BLUE, PURPLE, PINK, WHITE, SKYBLUE, P.YELLOW,
P.BLUE, P.PINK, L.RED, L.ORANGE, L.YELLOW, L.GREEN, P.GREEN, L.SKYBLUE,
L.BLUE, L.PURPLE
REVERSE
Parameter
SIZE
MUTE
REVERSE
1, then
RETRIG
Parameter
RETRIG
RETRIG GLD
HOLD
PITCH
Parameter
PIT CHRM
(PITCH CHRM)
PIT FINE
(PITCH FINE)
PIT BEND
(PITCH BEND)
PIT GLD
(PITCH GLIDE)
PAN
Parameter
PAN
LEVEL
LEV GLD
(LEVEL GLIDE)
FX SEND
Parameter
MFX1
MFX2
FX SEND
DRY
Value
Explanation
Specifies the range of steps to which the
1–16
effect is applied.
OFF, ON
Mutes the sound.
OFF, ON
Plays in reverse.
Value
Explanation
Repeatedly plays the sound for the specified
1–32
number of times within the range of steps
specified by SIZE.
Gradually applies change to the sound
specified by Retrig.
This is effective when you want the glitch
effect to change over time.
1/32–OFF–32, Inf
You can also produce change over a longer
time by raising Hold.
By setting this in the opposite direction than
a paired parameter, you can create large
change.
Repeatedly plays the range of steps specified
by SIZE for the specified number of times.
OFF, x1 - x16
If this is OFF, playback continues to the end
of the steps available, regardless of the step
range.
Value
Explanation
-24 (-2oct)
0 (Original)
Specifies the pitch in semitone units.
+24 (+2oct)
-100cent–0cent–
Finely adjusts the pitch.
+100cent
Smoothly varies the pitch across a wide
1%–100%–400%
range.
Applies gradual change to the specified
-400%–400%
pitch.
Value
Explanation
L128–0–127R
Specifies the panning of the sound.
0–255
Adjusts the volume.
Applies gradual change to the sound
-255–0–+255
specified by LEVEL.
Value
Explanation
Specifies the send amount of Scatter to
0–255
MFX1.
Specifies the send amount of Scatter to
0–255
MFX2.
Specifies the send amount to the SEND/
RETURN jacks.
0–255
* SEND/RETURN POS must be set to SCATTER.
Specifies the volume of sound that does not
0–255
pass through the effect.
SCATTER
39
Advertisement
Chapters
Table of Contents
