Labels & Cosmetics - Grizzly G0634XP Owner's Manual

800
COMBINATION MACHINE w/SPIRAL CUTTERHEAD
Specifications
Motor: 5 HP, 220V, Single-Phase, 60 Hz To reduce risk of serious personal injury when using this machine:
802
Full-Load Current Rating: 25A 1. Read and understand owner's manual before operating.
Cutterhead: Spiral w/Carbide Cutters 2. Always wear approved eye protection and respirator.
Number of Spiral Rows/Inserts: 4/32 3. Disconnect power before changing blades, removing
Replacement Inserts T24736 (10 Pack) parts, or doing maintenance, service, or adjustments.
4. Only plug power cord into a grounded outlet.
Indexable Cutter Size: 15 x 15 x 2.5mm
5. Do not wear loose clothing, gloves, jewelry, or other
Cutterhead Speed: 5034 RPM
items that can get entangled in moving parts. Tie back
Cuts Per Minute: 20,136
long hair and roll up long sleeves.
Max. Width of Cut: 12 in.
6. Ensure machine is correctly set up before starting.
Max. Depth of Cut: 1/8 in.
7. Do not plane two boards of varying thickness at the
Min. Stock Length: 14 in.
same time.
Weight: 610 lbs. 8. Never cut deeper than 1/8" on a single pass.
9. Never joint material smaller than 14" long, 3/4" wide, or
1/4" thick when edge jointing, or 1/2" thick when face
Date
planing.
10. Keep all guards in place and in proper operating
S/N
condition.
11. Make certain machine rests firmly on flat, level ground.
Mfd. for Grizzly in Taiwan
813
G0634Z
810
G0634XP
811(G0634Z)
814(G0634XP)
NOTICE
TO PREVENT DAMAGE TO
LOCKING MECHANISM, RELEASE
TABLE LOCK KNOB BEFORE
LOWERING TABLE.
REF PART # DESCRIPTION
800 P0634Z800 READ MANUAL LABEL
801 P0634Z801 RESPIRATOR/GLASSES LABEL
802 P0634Z802 MACHINE ID LABEL (G0634Z)
802 P0634XP802 MACHINE ID LABEL (G0634XP)
803 P0634Z803 CUTTERHEAD WARNING LABEL
804 P0634Z804 EAR PROTECTION LABEL
805 P0634Z805 DISCONNECT POWER LABEL
806 P0634Z806 CHANGING OPERATIONS WARNING LABEL
807 P0634Z807 TOUCH UP PAINT, GRIZZLY GREEN
808 P0634Z808 TOUCH UP PAINT, GREY PUTTY (G0634Z)
safety labels help reduce the risk of serious injury caused by machine hazards. if any label comes
off or becomes unreadable, the owner of this machine must replace it in the original location
before resuming operations. for replacements, contact (800) 523-4777 or www.grizzly.com.
BUY PARTS ONLINE AT GRIZZLY.COM!
-74-
Scan QR code to visit our Parts Store.
labels & cosmetics
806
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual, call
(800) 523-4777 or go to
www.grizzly.com.
MODEL G0634XP
POLAR BEAR SERIES JOINTER/PLANER
WARNING!
12. Do not allow hands or clothing to get pulled into
cutting area while feeding workpiece.
13. Be aware of "kickback" hazards and how to prevent
them.
14. Stand clear of board ends while planing.
15. Do not plane or joint boards with cracks, loose
knots, or other defects.
16. Always use push blocks when face planing.
17. Keep hands at least 4" away from cutterhead when
jointing.
18. Never reach into planer cutting area while machine is
running.
19. Do not operate when tired or under influence of drugs
or alcohol.
20. Do not expose to rain or use in wet locations.
21. Prevent unauthorized use by children or untrained
users; restrict access or disable machine when
unattended.
811(G0634XP)
801 803
DANGER!
ROTATING
CUTTERHEAD BELOW!
KICKBACK HAZARD! ALWAYS USE
EYE/LUNG INJURY
HAZARD! 1. Ensure outfeed table is PUSH BLOCKS!
Use this guard for all even with knives.
Push blocks minimize the
Always wear safety
operations possible, and 2. Never exceed the
possibility of operator's
glasses and a immediately reinstall it
maximum depth of cut.
respirator when following operations that hands contacting the
3. Do not stand directly
using this machine. require its removal. cutterhead while cutting.
behind workpiece.
807
812
NOTICE
Leaving the change lever
up for extended periods
may damage internal
components. Keep the
change lever down,
unless you are actively
planing workpieces.
REF PART #
808 P0634XP808 TOUCH-UP PAINT, PB WHITE (G0634XP)
809 P0634Z809
810 P0634Z810
810 P0634XP810 MODEL NUMBER LABEL (G0634XP)
811 P0634Z811
811 P0634XP811 POLAR BEAR LOGO 2-1/2 X 9-1/2 (G0634XP)
812 P0634Z812
813 P0634Z813
814 P0634XP814 TABLE LOCK KNOB NOTICE (G0634XP)
Model G0634Z/G0634XP (Mfd. Since 01/11)
806
805
DISCONNECT
POWER BEFORE
ADJUSTMENTS,
MAINTENANCE, OR
SERVICE.
808
804
HEARING LOSS
HAZARD!
Always wear hearing
protection when
using this machine!
809
DESCRIPTION
ELECTRICITY LABEL
MODEL NUMBER LABEL (G0634Z)
TABLE LOCK KNOB NOTICE (G0634Z)
CHANGE LEVER LABEL
GRIZZLY NAMEPLATE-SMALL