Table of Contents
Advertisement
Hardware (Not Shown)
Sliding Table:
— T-Bolts M12-1.75 x 50.............................. 3
— Flat Washers 12mm ................................ 3
— Lock Washers 12mm .............................. 3
— Hex Nuts M12-1.75 .................................. 3
— Push Handle M12-1.75 x 12 .................... 1
— Flat Washer 12mm .................................. 1
— Copper Flat Washer 12mm ..................... 1
— T-Nut M12-1.75 ........................................ 1
Wings:
— Set Screws M10-1.5 x 20 ........................ 5
— Hex Nuts M10-1.5 ................................... 5
Rip Fence:
— Handles M10-1.5 x 12 ............................. 2
— Knob M10-1.5 x 70 .................................. 1
— Button Head Cap Screws M6-1 x 12 ...... 3
— Flat Washers 6mm .................................. 4
—Hex Nut M6-1 .......................................... 1
Rip Fence Rail:
— Rip Fence Stop Ring w/Set Screw ......... 1
— Flat End Cap ........................................... 1
— Lock Washer 8mm .................................. 1
— Cap Screw M8-1.25 x 16 ........................ 1
Cross Cut Table:
— Lock Handle M12-1.75 x 55 ..................... 1
— Flat Washer 12mm .................................. 1
— T-Nut Plate M12-1.75 ............................... 1
Cross Cut Table Brace:
— T-Nuts M8-1.25 ....................................... 2
— Fender Washers 8mm ............................ 2
— Knobs M8-1.25 x 50 ................................ 2
Cross Cut Fence:
— T-Bolt M8-1.25 x 35 ................................ 1
— Fender Washer 8mm .............................. 1
— Knobs M8-1.25 ........................................ 2
— Pivot Stud M8-1.25 x 15 .......................... 1
—Fiber Flat Washers 8mm ........................ 2
— T-Nuts M8-1.25 ....................................... 3
— Knob M8-1.25 x 25 w/Nylon Tip.............. 1
— Knob M8-1.25 x 50 ................................. 1
— Stop Block............................................... 1
— Cap Screw M8-1.25 x 35 ........................ 1
— Lock Washer 8mm .................................. 1
—Plastic T-Washer 8mm ............................ 1
—Hex Nuts M8-1.25 ................................... 2
—Flat Washers 8mm ................................. 2
-18-
Qty
Dust Port Adapter:
— Button Head Cap Screws M6-1 x 12 ...... 2
— Lock Washers 6mm ................................ 2
—Flat Washers 6mm ................................. 2
Upper Support Arm Dust Port:
— Button Head Cap Screws M6-1 x 12 ...... 2
— Lock Washers 6mm ................................ 2
Blade Guard:
— Wire Clamps 3
—Compression Cylinder ............................ 1
—Dust Port Adapter 4" ............................... 1
Blade Guard Support Base, Pedestal, Arm, and
Connection Plate:
—Cap Screws M8-1.25 x 25 ...................... 4
—Flat Washers 8mm ................................. 4
—Lock Washers 8mm ................................ 4
—Cap Screws M6-1 x 20 ........................... 3
—Lock Washers 6mm ................................ 3
—Flat Washers 6mm ................................. 3
—L-Block .................................................... 1
—Cap Screws M6-1 x 20 ........................... 2
—Flat Washers 6mm ................................. 3
—Lock Washers 6mm ................................ 2
—Hex Nut M6-1 .......................................... 1
Crate 2 (Figure 9)
Y.
Sliding Table Assembly .............................. 1
Z. End Handle Assembly ................................ 1
—Button Hd. Cap Screws M8-1.25 x 16 .... 2
Z
Figure 9. Crate 2 inventory.
⁄
" .................................... 2
1
4
Y
Model G0699 (Mfd. Since 5/15)
Qty
Advertisement
Table of Contents
