Related Manuals for Siemens HiPath V6R1
Summary of Contents for Siemens HiPath V6R1
- Page 1 Documentation HiPath Wireless Outdoor AP V6R1 Installation Guide 9034532 Communication for the open minded Siemens Enterprise Communications www.siemens.com/open...
- Page 2 Subject to availability. Right of modification reserved. The trade- Siemens Enterprise Communications marks used are owned by Siemens Enterprise Communi- www.siemens.com/open cations GmbH & Co. KG or their respective owners.
-
Page 3: Table Of Contents
bkTOC.fm Nur für den internen Gebrauch Contents Contents 1 About this Guide ............... 5 1.1 Who should use this guide . - Page 4 bkTOC.fm Contents Nur für den internen Gebrauch 6.4 Brazil................50 6.5 ATEX, FM and cULus approvals .
-
Page 5: About This Guide
OutdoorAP_AboutThisGuide.fm About this Guide Who should use this guide 1 About this Guide The guide describes how to mount and connect cables to the HiPath Wireless Outdoor APs. In addition, this guide provides information on the product certifications and national approvals for the HiPath Wireless Outdoor APs. Note: This guide does not provide information on configuration of the HiPath Wireless Outdoor APs. -
Page 6: Formatting Conventions
OutdoorAP_AboutThisGuide.fm About this Guide Formatting conventions 1.3 Formatting conventions The HiPath Wireless Outdoor AP Installation Guide uses the following formatting conventions to make it easier to find information and follow procedures: • Bold text is used to identify components of the management interface, such as menu items and section of pages, as well as the names of buttons and text boxes. -
Page 7: Documentation Feedback
This device may only be used for the applications described in the catalog or the technical description and only in connection with devices or components from other manufacturers which have been approved or recommended by Siemens. Correct, reliable operation of the product requires proper transport, storage, positioning and assembly as well as careful operation and maintenance. - Page 8 You will find further information on this topic under the following URL: www.bitkom.org Disclaimer of liability Siemens has reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, Siemens cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions.
-
Page 9: Introduction
OutdoorAP_Intro.fm Introduction 2 Introduction Product Overview The HiPath Wireless Outdoor AP enables you to extend your Wireless LAN beyond the boundaries of indoor locations. They are resistant to harsh outdoor conditions and extreme temperatures. Using the advanced wireless distribution feature of the HiPath Wireless LAN, the HiPath Wireless Outdoor AP can extend your Wireless LAN to outdoor locations without Ethernet cabling. -
Page 10: Package Contents
A printed copy of the HiPath Wireless Outdoor AP Installation Instructions. Confirm that each HiPath Wireless Outdoor AP package is complete. If the package is not complete, contact your supplier or your local Siemens office. 2.2 HiPath Wireless Outdoor AP accessories list The following is the accessories list for the HiPath Wireless Outdoor AP. -
Page 11: Hipath Wireless Outdoor Aps Leds
OutdoorAP_Intro.fm Introduction HiPath Wireless Outdoor APs LEDs Product Description Order # (ordered from Siemens A&D) Power Module PM2 Power Supply 6GK5791-2AC00-0AA0 Input: 110-240VACOutput: 48VDC Mounting Set MS1 Mounting material specifically for the 6GK5798-8MG00-0AA0 HiPath Wireless Outdoor AP (wall, S7- 300 and 35mm DIN rail,... -
Page 12: Reset Button
OutdoorAP_Intro.fm Introduction Reset button 2.4 Reset button The reset button is located below the housing cover beside the sockets for external antennas as depicted in Figure 3 on page 12. You must remove the housing cover to gain access to the reset button. Warning You must remove the housing cover only after you have turned off the power supply of the HiPath Wireless Outdoor AP. -
Page 13: Mounting The Hipath Wireless Outdoor Aps
OutdoorAP_Description.fm Mounting the HiPath Wireless Outdoor APs Removing the housing cover 3 Mounting the HiPath Wireless Outdoor APs The first step to mounting the HiPath Wireless Outdoor AP is to remove the Wireless AP housing cover. 3.1 Removing the housing cover You have to remove the housing over if you want to carry out any of the following activities: •... -
Page 14: Fitting The Housing Cover
OutdoorAP_Description.fm Mounting the HiPath Wireless Outdoor APs Fitting the housing cover To remove the housing cover: 1. Remove the sealing caps from the housing cover (Position A in Figure 2. Loosen the screws in the cover (Position B in Figure Note: These screws remain in the cover after they have been loosened (this design element prevents them from being lost). -
Page 15: Grounding Terminal
OutdoorAP_Description.fm Mounting the HiPath Wireless Outdoor APs Attaching cables The available options are as follows: • The cables are inserted from above (Position A in Figure 5). The housing of the HiPath Wireless Outdoor AP has an opening at the top for this purpose. •... -
Page 16: Mounting Without An Adapter (Wall Mounting Only)
OutdoorAP_Description.fm Mounting the HiPath Wireless Outdoor APs Mounting without an adapter (wall mounting only) 3.4 Mounting without an adapter (wall mounting only) 3.4.1 Drilling template The location of the holes for mounting the HiPath Wireless Outdoor AP on a wall is depicted in Figure Figure 7... -
Page 17: Option: Threaded Holes On Rear Of Housing
OutdoorAP_Description.fm Mounting the HiPath Wireless Outdoor APs Mounting without an adapter (wall mounting only) To mount the HiPath Wireless Outdoor AP without an adapter (wall mounting only): 1. Lead the cables into the housing of the HiPath Wireless Outdoor AP (Position A in Figure Figure 8... -
Page 18: Mounting The Hipath Wireless Outdoor Ap With Mounting Plate
OutdoorAP_Description.fm Mounting the HiPath Wireless Outdoor APs Mounting the HiPath Wireless Outdoor AP with mounting plate 3.5 Mounting the HiPath Wireless Outdoor AP with mounting plate 3.5.1 Fitting the mounting plate to a wall The location of the holes for fitting the mounting plate to a wall is depicted in Figure Figure 9 Drilling template for fitting the mounting plate to a wall... -
Page 19: Screwing The Cover Plate To The Mounting Plate For The Cable Feedthrough
OutdoorAP_Description.fm Mounting the HiPath Wireless Outdoor APs Mounting the HiPath Wireless Outdoor AP with mounting plate Figure 10 Fitting the mounting plate to a wall 3.5.2 Screwing the cover plate to the mounting plate for the cable feedthrough The cabling of the HiPath Wireless Outdoor AP is led out of the rear of the device. The housing seal is effective only when it is not subjected to spray water. - Page 20 OutdoorAP_Description.fm Mounting the HiPath Wireless Outdoor APs Mounting the HiPath Wireless Outdoor AP with mounting plate To screw the cover plate to the mounting plate for the cables feedthrough: 1. Fit the cover plate on the mounting plate from below until the two lugs (Position A in Figure 11) engage the lower edge of the mounting plate.
-
Page 21: Fitting The Mounting Plate To An S7 Standard Rail
OutdoorAP_Description.fm Mounting the HiPath Wireless Outdoor APs Mounting the HiPath Wireless Outdoor AP with mounting plate 3.5.3 Fitting the mounting plate to an S7 standard rail To fit the mounting plate to a S7 standard rail: 1. Place the mounting plate with the two protruding catches on the top edge of the S7 standard rail (Position A in Figure 12). -
Page 22: Fitting The Mounting Plate To A Din Rail
OutdoorAP_Description.fm Mounting the HiPath Wireless Outdoor APs Mounting the HiPath Wireless Outdoor AP with mounting plate 3.5.4 Fitting the mounting plate to a DIN rail To fit the mounting plate to a DIN rail: 1. Place the mounting plate with the two catches (Position A in Figure 13) on the upper edge of the DIN rail. -
Page 23: Fitting The Mounting Plate To A Mast
OutdoorAP_Description.fm Mounting the HiPath Wireless Outdoor APs Mounting the HiPath Wireless Outdoor AP with mounting plate 3.5.5 Fitting the mounting plate to a mast To fit the mounting plate to a mast: 1. Feed the fastening straps through the openings in the mounting plate (position A in Figure 14). -
Page 24: Fitting The Hipath Wireless Outdoor Ap To A Mounting Plate
OutdoorAP_Description.fm Mounting the HiPath Wireless Outdoor APs Mounting the HiPath Wireless Outdoor AP with mounting plate 3.5.6 Fitting the HiPath Wireless Outdoor AP to a mounting plate To fit an HiPath Wireless Outdoor AP to a mounting plate: 1. Lead the cables into the housing of the HiPath Wireless Outdoor AP (Position A in Figure 15). - Page 25 OutdoorAP_Description.fm Mounting the HiPath Wireless Outdoor APs Mounting the HiPath Wireless Outdoor AP with mounting plate 4. Screw the HiPath Wireless Outdoor AP using the three M4 screws supplied with the mounting plate (Position C in Figure 16), tightening torque 1.8 Nm. Figure 16 Screwing HiPath Wireless Outdoor AP to a mounting plate 9034532, October 2009...
- Page 26 OutdoorAP_Description.fm Mounting the HiPath Wireless Outdoor APs Mounting the HiPath Wireless Outdoor AP with mounting plate 9034532, October 2009 HiPath Wireless Outdoor AP Installation Guide...
-
Page 27: Connecting Cables To The Hipath Wireless Outdoor Ap
A suitable lightning conductor is available in the range of accessories for the HiPath Wireless Outdoor AP (Lightning Protector LP798-1N, Order# 6GK5798- 2LP00-2AA6 from Siemens A&D). Warning Installing this lightning protector between an antenna and an HiPath Wireless Outdoor AP is not adequate protection against a lightning strike. - Page 28 OutdoorAP_ConnectingUp.fm Connecting cables to the HiPath Wireless Outdoor AP Safety extra low voltage Warning HiPath Wireless Outdoor APs are designed for operation with a directly connectable safety extra- low voltage or with the power supply adapters available as accessories (available only for HiPath Wireless Outdoor AP devices).
-
Page 29: Hipath Wireless Outdoor Ap Cables
OutdoorAP_ConnectingUp.fm Connecting cables to the HiPath Wireless Outdoor AP HiPath Wireless Outdoor AP cables Warning notices cULus haz.loc This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D; Class I, Zone 2, Group IIC or non-hazardous locations. WARNING - Cat. - Page 30 Antenna connector: N-Connect/R-SMA connecting cable The N Connect/R SMA male/male flexible connecting cable is available as an accessory for direct connection of an antenna to an HiPath Wireless Outdoor AP. Length in m Order number (ordered from Siemens A&D) 6XV1875-5CH10 6XV1875-5CH20 6XV1875-5CH50...
-
Page 31: Connecting The Cables
OutdoorAP_ConnectingUp.fm Connecting cables to the HiPath Wireless Outdoor AP Connecting the cables Length in m Order number (ordered from Siemens A&D) 6XV1875-5DE30 6XV1875-5DH20 Table 6 Antenna connector: R-SMA Male to SMA Male connecting cable 4.2 Connecting the cables Warning If the housing is not perfectly sealed and the HiPath Wireless Outdoor AP is subjected to spray water or dampness, you will endanger your life. - Page 32 OutdoorAP_ConnectingUp.fm Connecting cables to the HiPath Wireless Outdoor AP Connecting the cables You have the following options: • Connect cables pre-assembled with a connector (Ethernet, antennas) by inserting the connector into the appropriate socket. Secure antenna cables by tightening the sleeve nut of the connector (key size SW8). For more information, see Section 4.5, “Connecting an Ethernet cable to the HiPath Wireless Outdoor AP”, on page 36...
-
Page 33: Connecting A 48 V Dc Cable To The Hipath Wireless Outdoor Ap
OutdoorAP_ConnectingUp.fm Connecting cables to the HiPath Wireless Outdoor AP Connecting a 48 V DC cable to the HiPath Wireless Outdoor AP 4.3 Connecting a 48 V DC cable to the HiPath Wireless Outdoor AP Possible power supplies The following power supplies are suitable for the HiPath Wireless Outdoor AP: •... -
Page 34: Fitting A Power Supply Adapter
OutdoorAP_ConnectingUp.fm Connecting cables to the HiPath Wireless Outdoor AP Fitting a power supply adapter Figure 20 Position of the connector when inserted in the socket of the housing 2. Press the connector into the socket in the housing until it engages. 3. - Page 35 OutdoorAP_ConnectingUp.fm Connecting cables to the HiPath Wireless Outdoor AP Fitting a power supply adapter To fit and connect a power supply adapter: 1. Fit the power supply adapter in the HiPath Wireless Outdoor AP, as depicted Figure 21. The connector on the rear of the power supply adapter must engage fully in the socket of the housing.
-
Page 36: Removing The Power Supply Adapter
OutdoorAP_ConnectingUp.fm Connecting cables to the HiPath Wireless Outdoor AP Connecting an Ethernet cable to the HiPath Wireless Outdoor AP 4.4.1 Removing the power supply adapter To remove a power supply adapter from HiPath Wireless Outdoor AP: 1. Disconnect the power supply cable from the power supply adapter. Warning Disconnect power supply cables only when the power to the power supply adapter is turned off! 2. -
Page 37: Connecting An External Antenna Cable To The Hipath Wireless Outdoor Ap
OutdoorAP_ConnectingUp.fm Connecting cables to the HiPath Wireless Outdoor AP Connecting an external antenna cable to the HiPath Wireless Outdoor AP 4.6 Connecting an external antenna cable to the HiPath Wireless Outdoor For each WLAN port, there are two R-SMA sockets on the HiPath Wireless Outdoor AP to connect external antennas. - Page 38 OutdoorAP_ConnectingUp.fm Connecting cables to the HiPath Wireless Outdoor AP Connecting an external antenna cable to the HiPath Wireless Outdoor AP 9034532, October 2009 HiPath Wireless Outdoor AP Installation Guide...
-
Page 39: Technical Specifications
OutdoorAP_TechSPecifications.fm Technical Specifications HiPath Wireless Outdoor AP technical specifications 5 Technical Specifications 5.1 HiPath Wireless Outdoor AP technical specifications Product Versions The HiPath Wireless Outdoor AP with two wireless interfaces with two internal antennas or four external antenna connectors. Data Transfer Ethernet Transfer Rate 10/100Mbps Wireless Transmission Rate... -
Page 40: Optional Third-Party External Antennas
OutdoorAP_TechSPecifications.fm Technical Specifications Optional third-party external antennas Construction Dimensions (WxHxD) 251 mm x 251 mm x 72 mm Without power supply 2241 g adapter Weight With power supply 2433 g adapter 110-230 V AC Table 10 Construction Permitted ambient conditions Operating Temperature -40 °C to 70 °C Operation with 100 V /240 V power supply -40 °C to 60 °C... - Page 41 • The intended use is generally not for the general public. Instead, it is generally for industry/commercial use. Characteristics Antenna # and Frequency/ Antenna Impedence/Ω Order No. (ordered from Type gain/dBi Siemens A&D) Omni Antenna # 1 6GK5795-6MN00-0AA6 ANT795-6MN Omni Antenna # 2 6GK5792-6MN00-0AA6 ANT792-6MN...
-
Page 42: Antenna Channel-Power Settings
OutdoorAP_TechSPecifications.fm Technical Specifications Optional third-party external antennas Note: The antenna feedline of one metre used in testing are the minimum cable length. Longer cable may be used with losses greater than or equal to the cables used for testing. The maximum power settings must be adjusted according to table Antenna channel-power settings. - Page 43 OutdoorAP_TechSPecifications.fm Technical Specifications Optional third-party external antennas FCC/IC To fulfill all the requirements according to FCC Part 15.407 and RSS-210, the following software power setting is necessary. Mode Channels Antenna #1 Antenna # 3 Antenna # 4 Antenna # 8 ANT795-6MN ANT793-6MN ANT795-6DN...
- Page 44 OutdoorAP_TechSPecifications.fm Technical Specifications Optional third-party external antennas ETSI To fulfill all the requirements according to EN 301 893, the following software power setting is necessary. Mode Channels Antenna #1 Antenna # 3 Antenna # 4 Antenna # 6 Antenna # 8 ANT795-6MN ANT793-6MN ANT795-6DN...
-
Page 45: Certification
6.1 CE conformity The product HiPath Wireless Outdoor AP in the version put into circulation by Siemens A&D conforms to the regulations of the following European directive: • 99/5/EC Directive of the European Parliament and of the Council on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity. - Page 46 Devices connected to the system must meet the relevant safety regulations. The EC Declaration of Conformity is available for the responsible authorities according to the above-mentioned EC Directive at the following address: Siemens Aktiengesellschaft Automation and Drives Industrielle Kommunikation Postfach 4848 D-90327 Nürnberg...
- Page 47 OutdoorAP_Certification.fm Certification CE conformity Country 5.15-5.25 (GHz) 5.25-5.35 (GHz) 5.47-5.725 (GHz) 2.4-2.4835 (GHz) Channels: Channels: Channels: Channels: 1 to 13 36,40,44,48 52,56,60,64 100,104,108,112,116, (Except Where Noted) 120,124,128,132,136, Austria Indoor only Indoor only Indoor or outdoor Indoor or outdoor Belgium Indoor only Indoor only Indoor or outdoor * Indoor or outdoor...
-
Page 48: Fcc
1 through11. Note: Changes or modifications made to this equipment not expressly approved by SIEMENS may void the FCC authorization to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. -
Page 49: Industry Canada
OutdoorAP_Certification.fm Certification Industry Canada • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Note: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. -
Page 50: October
OutdoorAP_Certification.fm Certification Brazil “Users should also be cautioned to take note that high power radars are allocated as primary users (meaning they have priority) of 5250-5350 MHz and 5650-5850 MHz and these radars could cause interference and/or damage to LE-LAN devices.”... - Page 51 OutdoorAP_Certification.fm Certification NEMA 4X • c-UL-us for hazardous location: UL 1604, CSA C22.2 No. 213-M1987 CL. 1, Div. 2 GP. A.B.C.D T4 CL. 1, Zone 2, GP, IIC, T4 Ta : -40°C to 70°C 100 V to 240 V Ta: -40°C to +60°C Note: The specified approvals apply only when the corresponding mark is printed on the product.
- Page 52 OutdoorAP_Certification.fm Certification NEMA 4X 9034532, October 2009 HiPath Wireless Outdoor AP Installation Guide...
- Page 53 bkIX.fm Nur für den internen Gebrauch Index Index guide about this 5 what is in it 5 who should use it 5 HiPath Wireless Outdoor AP about this guide 5 connecting 48 V DC 33 accessories list 10 connecting cables 27 attaching connecting ethernet cable 36 cables 14...
- Page 54 bkIX.fm Index Nur für den internen Gebrauch removing 36 prescribed usage 7 product overview 9 qualified personnel 7 removing housing cover 13 power supply adapter 36 reset button 12 safety extra low voltage 28 information 7 rules 31 screwing cover plate to mounting plate for cable feedthrough 19 technical specifications 39 terminal, grounding 15...