Connections - Siemens Cerberus CS1140 Manual

E3X102/103 Master module (supersedes E3X101)
9.6

Connections

E3X102/103
Programmable
control inputs,
EMI-protected
Y8
Remote transmission
X8
ALARM (LED H7 L.)
Remote transmission
FAULT (LED H7 R.)
(Normal operation = 9/10 closed)
Module chassis ground
Q1
LED
Q2
Q3
Programmable
Q4
control outputs,
Q5
24V/40mA,
EMI-protected Q6
Q7
Q8
programmable control
in-/outputs
Q/I1
(as output max. 24V/40mA)
Silence horn
Emergency op
Fire alarm
eration circuit,
EMI-protected
unused
C-Bus
Supply B3Q...,
2)
24V/max. 2A
Ground
C-Bus (feedback)
Supply for B3Q...,
second supply line
unused
Monitored control line:
H6 L.
Alarm horn 1
LED
Monitored control line:
H6 R.
Alarm horn 2
LED
1) The polarity at terminals 17...20 applies to the active state
2) Supply outputs to AlgoPilot B3Q... X16-8, 9, 14, 15 are not monitored
3) Terminate not used horn lines with a 4.75kΩ resistor
56
Building Technologies
Fire Safety & Security Products
Terminal block X15
1
I1 F28
I2
F29
2
I3
F30
3
I4
F31
4
C
F32
5
6
1A/30V 7
8
9
1A/30V
10
11 (connect to chassis ground)
- 12
F17
H2 L.
H2 R. F18 - 13
H3 L. F19
- 14
H3 R. F20
- 15
H4 L.
F21
- 16
H4 R. F22
- 17
H5 L.
F23
- 18
H5 R. F24 - 19
C
F25
+ 20
L. = left
R. = right
X16
Terminal block
1
F9
2
F10
F12 3
C - 4
F11
5
A1 6
B1 7
+ 8
F13
F15 - 9
10
11
12
A2
13
B2
+ 14
F14
2)
F16 - 15
16
F5 - 17
24V
F6 18
+
1) 3)
F7 - 19
24V
+ 20
F8
Signal transmitter (contact)
(also permissible outside control unit housing)
To remote transmission equipment
Relay
(also permissible outside control unit housing)
Signal transmitter (contact)
(also permissible outside control unit housing)
Relay
(also permissible outside control unit housing)
- Connection required if B3Q... should have
- essential with at least one control console
B3Q...
- parallel to all B3Q... (and E3X10. and
K6-2
K6-1
K7-3
K5-4
- Cabling C-Bus
K5-3
or
K7-1
K7-3
- for cable type (impedance adaption see table
K7-2
K7-5
K5-2
K5-1
K7-4
K7-6
4.75kΩ
max. 2A
max. 2A
4.75kΩ
"Emergency operation" capability
E3H020) if several have to be linked
max. 1000m per loop with ø0.6 mm wire
max. 1400m per loop with ø0.8mm wire
(always including return line)
adapt C-Bus impedance
External audible alarm devices
001260_k_en_--.doc
02.2005