Menu - ADEMCO VISTA-50P Quick Start Manual

Standard default (*97) values are shown in brackets [ ], otherwise default = 0. Fields bordered by dotted line can be
programmed using the #93 Menu mode.
* 0 0
INSTALLER CODE
Enter 4 digits, 0-9 [4140]
ASSIGN RESPONSE TYPE FOR ZONES 1-27, 95-99
(Enter 00-10) see fields 1*01-1*09 for response types for zones 28-87.
*02 *03
1 | 9 | 17
2 | 10 | 18
3 | 11 | 19
4 | 12 | 20
5 | 13 | 21
6 | 14 | 22
7 | 15 | 23
8 | 16 | 24
RESPONSE TYPES: 00 = Disabled zone; 01 = Entry/Exit #1;
02 = Entry/Exit #2; 03 = Perimeter; 04 = Interior Follower;
05 = Day/Night; 06 = 24 hour Silent Alarm; 07 = 24 hour Audible Alarm;
08 = 24 hour Auxiliary; 09 = Fire; 10 = Interior, Delay; 20 = arm stay;
21 = arm away; 22 = disarm; 23= no alarm response
* 0 9
ENTRY DELAY #1
00-15 times 15 seconds
Maximum 3 for UL Listed installations.
* 1 0
EXIT DELAY #1
00-15 times 15 seconds
Maximum 4 for UL Listed installations.
* 1 1
ENTRY DELAY #2
00-15 times 15 seconds
Maximum 3 for UL Listed installations.
* 1 2
EXIT DELAY #2
00-15 times 15 seconds
Maximum 4 for UL Listed installations.
* 1 3
ALARM SOUNDER DURATION
01-15 times 2 minutes. Minimum 4 minutes for UL.
* 1 4
ZONE 9 RESPONSE TIME
1=fast; 0= normal; "0" for UL.
* 1 5
KEYSWITCH ASSIGNMENT
Enter partition in which keyswitch used, 1-8; 0=disable
*16
CONFIRMATION OF ARMING DING
1=enable; 0=disable
* 1 7
AC LOSS KEYPAD SOUNDING
1=yes; 0=no
* 1 8 UL
AC LOSS SIREN
1=yes; 0=no
* 1 9
RANDOMIZE AC LOSS REPORT
1=randomize 10-40 min.; 0=no
* 2 0
VOICE MODULE PHONE CODE [00]
Enter 01-09 for 1st digit; 11 (for *) or 12 (for #) for 2nd digit.
To disable voice module, enter 1st digit = 00 & 2nd digit = 11
Must be disabled for UL Listed installations.
* 2 1
PREVENT FIRE TIME-OUT
1=no timeout; 0=fire timeout
* 2 2
KEYPAD PANIC ENABLES
1=enable; 0=disable
* 2 3
MULTIPLE ALARMS
1=yes; 0=no
* 2 4
IGNORE EXPANSION ZONE TAMPER
1=yes; 0=enable for RF and RPMs
VISTA 50P/VISTA 50-PUL
SINGLE PARTITION PROGRAMMING FORM
*04 *05
| 25 |
| 26 |
| 27 |
| 0 | 0
| 97 |
polling loop short
| 95 |
(1+ panic)
| 96 |
(3+ # panic)
| 99 |
( + # panic)
[02]
[03]
[06]
[08]
[04]
|
[001]
95 96
* 2 5
| | | BURG.TRIGGER FOR RESPONSE TYPE 8
1=enable; 0=disable
* 2 6
INTELLIGENT TEST REPORTING
Set "0" for UL 1=yes, (no report sent if any other report
was recently sent); 0=no
* 2 7
TEST REPORT INTERVAL
Enter interval in hours, 001-999; 000=no report ; Max. 024
for UL.
* 2 8
POWER UP IN PREVIOUS STATE
1=yes; 0=no; "1" for UL.
* 2 9
QUICK ARM
1=yes; 0=no
* 3 0
TOUCH-TONE OR ROTARY DIAL
1=TouchTone; 0=rotary
* 3 1
PABX ACCESS CODE
00-09; B-F (11-15)
* 3 2
PRIMARY SUBSCRIBER ACCT #
|
Enter 00-09; B-F (11-15) [15 15 15 15]
|
* 3 3
PRIMARY PHONE NUMBER
|
Enter 0-9 for each digit; enter #11 for *, #12 for #, and #13 for
2 sec. pause
|
* 3 4
SECONDARY PHONE NUMBER
|
Enter 0-9 for each digit; enter #11 for *, #12 for #, and #13 for
2 sec. pause
*35
DOWNLOAD PHONE No.
|
[0]
Enter 0-9 for each digit; enter #11 for *, #12 for #, and #13 for
2 sec. pause
[0]
* 3 6
DOWNLOAD ID No.
| |
[0]
Enter 00-09; A-F (10-15) [15 15 15 15 15 15 15 15]
* 3 7
DOWNLOAD COMMAND ENABLES
[0]
Dialer System
[0]
Shutdwn Shutdwn
See field 1*53 for Callback disable option; [1=enable]; 0=disable; For UL
installations, all options must be disabled.
[0]
* 3 8 PREVENT ZONE XX BYPASS
01-86; 00 if all zones (except Fire zones) can be bypassed
|
* 3 9 ENABLE OPEN/CLOSE REPORT
FOR INSTALLER CODE
1=enable; 0=disable
[0]
* 4 0 OPEN/CLOSE REPORT FOR KEYSWITCH
1=enable; 0=disable
* 4 1 NORMALLY CLOSED or EOLR (Zones 2-8)
99
1=N.C.loops; 0=EOLR supervision; Must be "0" for UL.
[1]
* 4 2 DIAL TONE PAUSE
0=5 seconds; 1=11 seconds; 2=30 seconds; Must be "0" for UL.
[0]
| |
| | |
| | |
0
Not Remote Remote Remote Upload
Used Bypass Disarm Arm
[1]
[0]
| |
[024]
[1]
[1]
[0]
| |
| | |
Download
Program Program
[00] |
[0]
[0]
[1]
[0]
– 7 –