Roland VC-2 Owner's Manual page 58

Effects List
35: Bass Multi
Bass Multi provides Comp/Limiter, Overdrive or Distortion,
3-band equalizer, and Chorus or Flanger effects connected in
series. This algorithm is a multi-effects for bass.
Parameter Value
Comp Sw OFF, ON
Comp -60–0 dB
Threshold
Comp Attack 0–127
Comp Re- 0–127
lease
Comp Ratio 1.5:1, 2:1, 4:1,
100:1
Comp Gain -60– +12 dB
Od/Ds Sw OFF, ON
Drive Mode OD, DS
Drive 0–127
Amp Sim Sw OFF, ON
Amp Type SMALL,
BUILT-IN,
2-STACK
(STACK)
Distortion 0–127
(DS) Level
EQ Low Freq 50–4000 Hz
EQ Low Gain -15– +15 dB
EQ Mid Freq 50–20000 Hz
EQ Mid Q 0.5, 0.7, 1.0, 2.0,
4.0, 8.0
EQ Mid Gain -15– +15 dB
EQ Hi Freq 2000–20000 Hz
EQ Hi Gain -15– +15 dB
Mod Mode CHORUS,
FLANGER
Mod Rate 0.05–10.0 Hz,
note
Mod Depth 0–127
Mod Phase 0–180 deg
Mod Pre De- 0–50.0 ms
lay
Mod Feed- -98– +98 %
back
58
Description
Turns the comp/limiter on/off.
Sets the volume level at which the
compression begins.
Sets the time after the sound vol-
ume is crossed the compressor
threshold until compression be-
gins.
Specifies the time from when the
volume drops below the compres-
sor threshold until compression is
no longer applied.
Sets the "source sound:output
sound" compression ratio.
Adjusts the output gain.
Selects whether to use overdrive
or distortion.
Selects whether to use overdrive
(OD) or distortion (DS).
Degree of distortion
Turns the amp simulator on/off.
Type of guitar amp
SMALL: small amp
BUILT-IN: single-unit type amp
2-STACK: large double stack amp
Volume of the overdrive or distor-
tion sound.
Frequency of the low range
Gain of the low range
Frequency of the middle range
Gain of the middle range
Set a higher value for Q to narrow
the range to be affected.
Gain of the middle range
Frequency of the high range
Gain of the high range
Selects whether to use chorus or
flanger.
Adjusts the speed of modulation
for the chorus or flanger.
Adjusts the depth of modulation
for the chorus or flanger.
Sets how the chorus or flanger
sound is spread.
Adjusts the delay time from the di-
rect sound until the chorus or
flanger sound is heard.
Adjusts the proportion of the ef-
fect sound that is fed back into the
effect. Negative (-) settings will in-
vert the phase.
Parameter Value
Mod Xover- 500–15000 Hz,
LPF THRU
Mod Xover- THRU,
HPF 50–800 Hz
Mod Level 0–127
36: E.Piano Multi
Enhancer, Phaser, Chorus or Flanger, and Tremolo or Auto-
pan are connected in series. This effect is used for electric
piano.
Parameter Value
Enhan Sw OFF, ON
Enhan Sens 0–127
Enhan Fre- 0–127
quency
Enhan Mix 0–127
Level
Enhan Lev- 0–127
el
Phaser 0–127
Manual
Phaser Rate 0.05–10.0
Hz, note
Phaser 0–127
Depth
Phaser Res- 0–127
onance
Phaser Mix 0–127
Level
Mod Mode CHORUS,
FLANGER
Mod Rate 0.05–10.0
Hz, note
Mod Depth 0–127
Mod Phase 0–180 deg
Mod Pre 0–50.0 ms
Delay
Mod Feed- -98– +98 %
back
Mod Xover- 500–15000
LPF Hz, THRU
Mod Xover- THRU, 50–
HPF 800 Hz
Description
Adjusts the cutoff frequency of the
low pass filter. (THRU: no filter is
used)
Adjusts the cutoff frequency of the
high pass filter. (THRU: no filter is
used)
Volume of the chorus or flanger
sound.
Description
Turns the enhancer effect on/off.
Sensitivity of the enhancer
Sets the lower limit of the frequencies
to which the enhancement effect is
added.
Level of the overtones generated by
the enhancer
Volume of the enhancer sound
Specifies the center frequency at
which the sound is modulated.
Specifies the frequency of modula-
tion.
Specifies the depth of modulation.
Specifies the amount of feedback for
the phaser.
Higher settings will give the sound a
stronger character.
Specifies the volume of the phase-
shifted sound, relative to the direct
sound.
Selects whether to use chorus or
flanger.
Adjusts the speed of modulation for
the chorus or flanger.
Adjusts the depth of modulation for
the chorus or flanger.
Sets how the chorus or flanger sound
is spread.
Adjusts the delay time from the direct
sound until the chorus or flanger
sound is heard.
Adjusts the proportion of the effect
sound that is fed back into the effect.
Negative (-) settings will invert the
phase.
Adjusts the cutoff frequency of the
low pass filter. (THRU: no filter is
used)
Adjusts the cutoff frequency of the
high pass filter. (THRU: no filter is
used)