Roland VC-2 Owner's Manual page 38

Settings Common to All Modes (System Mode)
EQ
Parameter Value
2 Band EQ OFF, ON
LOW Freq 50, 63, 80, 100,
125, 160, 200,
250, 315, 400,
500, 630, 800,
1000, 1250, 1600,
2000, 2500, 3150,
4000 Hz
LOW Gain -15– +15 dB
HIGH Freq 2000, 4000, 5000,
6300, 8000,
10000, 12500,
16000, 20000 Hz
HIGH Gain -15– +15 dB
TOTAL -15– +15 dB
Gain
MIDI/USB
Parameter Value
Device ID 17–32
Clock INT,
Source MIDI,
USB MIDI
Rx Sw OFF, ON
Rx Channel 1–16
Rx PC OFF, ON
Rx Bank OFF, ON
Rx Sys-Ex OFF, ON
38
Explanation
Switch the 2-Band equalizer
on/off.
Selects the frequency of the low
range.
Adjusts the gain of the low fre-
quency. Positive (+) settings
will emphasize the low-fre-
quency range.
Selects the frequency of the high
range.
Adjusts the gain of the high fre-
quency. Positive (+) settings
will emphasize the high-fre-
quency range.
Adjusts the total gain.
Explanation
When you want to transmit or re-
ceive System Exclusive messages,
set this parameter to match the De-
vice ID number of the other MIDI
device.
The LFO cycle or multi-effects
changes can be synchronized to a
clock (tempo). When this is used
by the patch, this Clock Source set-
ting determines the clock which
will be used.
INT: The Patch Tempo will be
used.
MIDI: Synchronize to the clock of
an external MIDI.
USB MIDI: Synchronize to the
clock of an external USB MIDI.
Specifies whether all MIDI mes-
sages will be received (ON) or not
(OFF).
Sets the Basic Channel (MIDI chan-
nel on which the VC-2 receives and
transmits messages).
Specifies whether Program
Change messages will be received
(ON) or not (OFF).
Specifies whether Bank Select mes-
sages will be received (ON) or not
(OFF).
Specifies whether System Exclu-
sive messages will be received
(ON) or not (OFF).
Parameter Value
Tx Edit OFF, ON
Clock Out OFF, ON
USB-MIDI OFF, ON
Thru Sw
Volume OFF, ON
Expression
Level Con-
trol
Chord Memory
Parameter Value Explanation
Chord OFF, Switches the Multi Chord Memory (one-
Memory ON finger chord) function on/off.
Sw
* If you want to synchronize to an external
Grid Reso- Dot- Each note within the chord will be played
lution ted 8th separately at the timing interval you
note– specify here.
64th
note
Code set C–B Specify a chord for each key in the range
C–B.
KEEP OFF, When entering a chord from the key-
ON board, this parameter specifies whether
the keys you press will be held in their
pressed state (ON) or not (OFF). If this is
ON, the key will be maintained in a
"pressed" state even when you release it.
Explanation
Specify whether changes you
make in the settings of a patch will
be transmitted as system exclusive
messages (ON), or will not be
transmitted (OFF).
Specifies whether MIDI clock will
be transmitted (ON) or not (OFF).
This switch specifies whether
MIDI messages received at the
MIDI connector will be re-trans-
mitted from the MIDI OUT con-
nector (ON) or not (OFF).
MIDI IN
MIDI OUT
USB OUT
Sound
Generator
Section
V-Synth XT
USB-MIDI Thru Sw=OFF
MIDI IN
MIDI OUT
USB OUT
Sound
Generator
Section
V-Synth XT
USB-MIDI Thru Sw=ON
Specifies whether received Vol-
ume or Expression Pedal messages
will adjust the output volume
(ON), or will be ignored (OFF).
device, set Clock Source (p. 38) to
EXTERNAL, then get your external
device to transmit clock messages. If you
fail to do this, chords will not play
correctly.
USB IN
USB IN