Roland VC-2 Owner's Manual page 48

Effects List
Parameter Value
Delay 0–1300 ms
Time (MONO),
0–650 ms (STE-
REO, ALTER-
NATE), note
L-R Shift 0–650 ms, note
L-R Order L→R, R→L
Feedback -98– +98 %
Low Damp 50–4000 Hz
Freq
Low Damp -36–0 dB
Gain
Hi Damp 2000–20000 Hz
Freq
Hi Damp -36–0 dB
Gain
Balance DRY100:0WET–
DRY0:100WET
Ps Low 50–4000 Hz
Freq
Ps Low -15– +15 dB
Gain
Ps Hi Freq 2000–20000 Hz
Ps Hi Gain -15– +15 dB
48
Description
Adjusts the delay time from the di-
rect sound until the delay sound is
heard.
Of the left and right delay sounds,
the delay time will be increased for
only one side.
If the L-R order is L→R, the R
sound will be later. In the case of
R→L, the L sound will be later.
When the mode is set to MONO or
ALTERNATE, this setting will be
ignored.
In STEREO or ALTERNATE mode,
this setting determines which of the
left or right sides has the delay
sound before the other
L→R: The left side is expressed first
R→L: The right side is expressed
first
* In MONO mode, this setting will
be ignored.
Adjusts the proportion of the delay
sound that is fed back into the ef-
fect. Negative (-) settings will in-
vert the phase.
Adjusts the frequency below which
sound fed back to the effect will be
cut.
The Low Damp function damps the
low frequency band of the delay
sound quicker than other bands,
which makes for a clearer delay ef-
fect.
Degree of Low Damp
Adjusts the frequency above which
sound fed back to the effect will be
cut.
High Damp, by attenuating the
higher frequencies first, makes the
delay sound more natural.
Degree of High Damp
Volume balance between the direct
sound (DRY) and the delay sound
(WET)
Frequency of the low range
Gain of the low range
Frequency of the high range
Gain of the high range
12: Multi Tap Delay
The effect has five delays. Each of the Delay Time parameters
can be specified as a note length of the selected tempo. You
can also set the panning and level of each delay sound.
Parameter Value
Delay 1–5 0–1300 ms,
note
Fbk Dly 0–1300 ms,
Time note
Feedback -98– +98 %
Delay 1–5 0–127
Level
Delay 1–5 L63–63R
Pan
Low Damp 50–4000 Hz
Freq
Low Damp -36–0 dB
Gain
Hi Damp 2000–20000 Hz
Freq
Hi Damp -36–0 dB
Gain
Ps Low Freq 50–4000 Hz
Ps Low Gain -15– +15 dB
Ps Hi Freq 2000–20000 Hz
Ps Hi Gain -15– +15 dB
Description
Specifies the delay time from the
original sound until each delay
sound (Delay 1/2/3/4/5) is heard.
Adjusts the delay time for the feed-
back sound
Adjusts the proportion of the delay
sound that is fed back into the ef-
fect. Negative (-) settings will in-
vert the phase.
Adjusts the volume of each delay
sound (Delay 1/2/3/4/5)
Adjusts the pan of each delay
sound (Delay 1/2/3/4/5)
Adjusts the frequency below which
sound fed back to the effect will be
cut.
The Low Damp function damps the
low frequency band of the delay
sound quicker than other bands,
which makes for a clearer delay ef-
fect.
Degree of Low Damp
Adjusts the frequency above which
sound fed back to the effect will be
cut.
High Damp, by attenuating the
higher frequencies first, makes the
delay sound more natural.
Degree of High Damp
Frequency of the low range
Gain of the low range
Frequency of the high range
Gain of the high range