Roland VC-2 Owner's Manual page 54

Effects List
Parameter Value
Balance DRY100:0WET–
DRY0:100WET
Ps Low Freq 50–4000 Hz
Ps Low Gain -15– +15 dB
Ps Hi Freq 2000–20000 Hz
Ps Hi Gain -15– +15 dB
27: Stereo Pitch Shifter
This effect features two pitch shifters arranged in parallel,
making it stereo compatible. It can shift the pitch of the input
signal up to one octave up or down.
Parameter Value
Input Mode MONO,
STEREO
Grade 1–5
Coarse Pitch -12– +12
A/B semitone
Fine Pitch A/ -100– +100
B cent
Pre Delay A/ 0–500 ms
B
Level A/B 0–127
Pan A/B L63–63R
Direct Level 0–127
Feedback -98– +98 %
Low Damp 50–4000 Hz
Freq
Low Damp -36–0 dB
Gain
Hi Damp 2000–20000 Hz
Freq
Hi Damp -36–0 dB
Gain
Ps Low Freq 50–4000 Hz
Ps Low Gain -15– +15 dB
Ps Hi Freq 2000–20000 Hz
Ps Hi Gain -15– +15 dB
54
Description
Volume balance between the di-
rect sound (DRY) and the effect
sound (WET)
Frequency of the low range
Gain of the low range
Frequency of the high range
Gain of the high range
Description
Selects either stereo input or mon-
aural input.
Sets the grade of the effect sound.
The higher the value is set, the
more natural-sounding can be ob-
tained; however, this increases the
delay from the source sound as
well.
Specifies the pitch shift amount in
semitones for pitch shift A or B.
Adjusts the pitch shift amount in
2-cent units (1 cent = 1/100 of a
semitone) for pitch shift A or B.
Adjusts the delay time from the di-
rect sound until the pitch shift A
or B sound is heard.
Volume of the pitch shift A or B
sound.
Pan of the pitch shift A or B sound.
Volume of the direct sound.
Adjusts the proportion of the pitch
shift sound that is fed back into the
effect. Negative (-) settings will in-
vert the phase.
Adjusts the frequency below
which sound fed back to the effect
will be cut.
The Low Damp function damps
the low frequency band of the
pitch shift sound quicker than oth-
er bands.
Degree of Low Damp
Adjusts the frequency above
which sound fed back to the effect
will be cut.
High Damp, by attenuating the
higher frequencies first.
Degree of High Damp
Frequency of the low range
Gain of the low range
Frequency of the high range
Gain of the high range
28: OD/DS→Cho/Flg (Overdrive/
Distortion→Chorus/Flanger)
This effect connects either Overdrive or Distortion and either
Chorus or Flanger.
Parameter Value
Drive Mode OD, DS
Drive 0–127
Amp Sim Sw OFF, ON
Amp Type SMALL,
BUILT-IN,
2-STACK,
3-STACK
Distortion 0–127
(DS) Level
Mod Mode CHORUS,
FLANGER
Mod Rate 0.05–10.0 Hz,
note
Mod Depth 0–127
Mod Phase 0–180 deg
Mod Pre De- 0–50.0 ms
lay
Mod Feed- -98– +98 %
back
Xover Low- 50–4000 Hz
Freq
Xover Low -36–0 dB
Gain
Xover Hi- 2000–20000 Hz
Freq
Xover Hi -36–0 dB
Gain
Mod Level 0–127
Ps Low Freq 50–4000 Hz
Ps Low Gain -15– +15 dB
Ps Hi Freq 2000–20000 Hz
Ps Hi Gain -15– +15 dB
Description
Selects whether to use overdrive
(OD) or distortion (DS).
Degree of distortion
Turns the amp simulator on/off.
Type of guitar amp
SMALL: small amp
BUILT-IN: single-unit type amp
2-STACK: large double stack amp
3-STACK: large triple stack amp
Volume of the overdrive or distor-
tion sound.
Selects whether to use chorus or
flanger.
Adjusts the speed of modulation
for the chorus or flanger.
Adjusts the depth of modulation
for the chorus or flanger.
Sets how the chorus or flanger
sound is spread.
Adjusts the delay time from the di-
rect sound until the chorus or
flanger sound is heard.
Adjusts the proportion of the effect
sound that is fed back into the ef-
fect. Negative (-) settings will in-
vert the phase.
Attenuates the effect in the range
below the specified frequency.
Specifies how greatly the low
range will be attenuated.
Attenuates the effect in the range
above the specified frequency.
Specifies how greatly the high
range will be attenuated.
Volume of the chorus or flanger
sound.
Frequency of the low range
Gain of the low range
Frequency of the high range
Gain of the high range