Roland VC-2 Owner's Manual page 56

V-card software series vocal designer for v-synth xt
Hide thumbs Also See for VC-2:
Table of Contents

Advertisement

Effects List
31: Enh→Cho/Flg
(Enhancer→Chorus/Flanger)
This effect connects Enhancer and either Chorus or Flanger in
series.
Parameter
Value
Enhan Sens
0–127
Enhan Fre-
0–127
quency
Enhan Mix
0–127
Level
Enhan Level
0–127
Mod Mode
CHORUS,
FLANGER
Mod Rate
0.05–10.0 Hz,
note
Mod Depth
0–127
Mod Phase
0–180 deg
Mod Pre De-
0–50.0 ms
lay
Mod Feed-
-98– +98 %
back
Xover Low-
50–4000 Hz
Freq
Xover Low
-36–0 dB
Gain
Xover Hi-
2000–20000 Hz
Freq
Xover Hi
-36–0 dB
Gain
Mod Level
0–127
Ps Low Freq
50–4000 Hz
Ps Low Gain
-15– +15 dB
Ps Hi Freq
2000–20000 Hz
Ps Hi Gain
-15– +15 dB
32: Enh→Delay (Enhancer→Delay)
This effect connects an Enhancer and a Delay in series.
Parameter
Value
Enhan Sens
0–127
Enhan Fre-
0–127
quency
Enhan Mix
0–127
Level
Enhan Level
0–127
Delay Time
0–1300 ms,
note
56
Description
Sensitivity of the enhancer
Sets the lower limit of the frequen-
cies to which the enhancement ef-
fect is added.
Level of the overtones generated by
the enhancer
Volume of the enhancer sound
Selects whether to use chorus or
flanger.
Adjusts the speed of modulation
for the chorus or flanger.
Adjusts the depth of modulation
for the chorus or flanger.
Sets how the chorus or flanger
sound is spread.
Adjusts the delay time from the di-
rect sound until the chorus or
flanger sound is heard.
Adjusts the proportion of the effect
sound that is fed back into the ef-
fect. Negative (-) settings will in-
vert the phase.
Attenuates the effect in the range
below the specified frequency.
Specifies how greatly the low range
will be attenuated.
Attenuates the effect in the range
above the specified frequency.
Specifies how greatly the high
range will be attenuated.
Volume of the chorus or flanger
sound.
Frequency of the low range
Gain of the low range
Frequency of the high range
Gain of the high range
Description
Sensitivity of the enhancer
Sets the lower limit of the frequen-
cies to which the enhancement ef-
fect is added.
Level of the overtones generated by
the enhancer
Volume of the enhancer sound
Adjusts the delay time from the di-
rect sound until the delay sound is
heard.
Parameter
Value
Delay Feed-
-98– +98%
back
Low Damp
50–4000 Hz
Freq
Low Damp
-36–0 dB
Gain
Hi Damp
2000–20000 Hz
Freq
Hi Damp
-36–0 dB
Gain
Delay Level
0–127
Ps Low Freq
50–4000 Hz
Ps Low Gain
-15– +15 dB
Ps Hi Freq
2000–20000 Hz
Ps Hi Gain
-15– +15 dB
33: Vocal Multi
A limiter/de-esser, enhancer, 3-band equalizer, and delay are
connected in series.
A limiter holds down high signal levels to prevent distortion.
A de-esser cuts the sibilant sounds of a voice, producing a
gentler tone.
Parameter
Value
Limtr Mode
LIMITER,
DE-ESSER
Limtr
-60–0 dB
Threshold
Limtr Re-
0–127
lease
Limtr Gain
-60– +12 dB
DE Sens
0–127
DE Frequen-
1000–10000 Hz
cy
Description
Adjusts the proportion of the delay
sound that is fed back into the ef-
fect. Negative (-) settings will in-
vert the phase.
Adjusts the frequency below which
sound fed back to the effect will be
cut.
The Low Damp function damps the
low frequency band of the delay
sound quicker than other bands,
which makes for a clearer delay ef-
fect.
Degree of Low Damp
Adjusts the frequency above which
sound fed back to the effect will be
cut.
High Damp, by attenuating the
higher frequencies first, makes the
delay sound more natural.
Degree of High Damp
Volume of the delay sound.
Frequency of the low range
Gain of the low range
Frequency of the high range
Gain of the high range
Description
Selects whether the effect will
function as a limiter or as a de-ess-
er.
* If the Limtr Mode is DE-ESSER,
the limiter settings are ignored.
Conversely, if the Limtr Mode is
LIMITER, the de-esser settings are
ignored.
Adjusts the level (Threshold Lev-
el) at which the limiter will begin
to operate.
Adjusts the time until when the
limiter will turn off after the input
level falls below the threshold lev-
el.
Adjusts the gain of the sound that
passes through the limiter.
Adjusts the sensitivity relative to
the input volume, which controls
how the effect is applied.
Adjusts the frequency at which the
de-esser effect will apply.

Advertisement

Table of Contents
loading

This manual is also suitable for:

V-card vc-1

Table of Contents