Table of Contents
Advertisement
MIDI Implementation
Vibrato Rate (Controller number 76)
Status
2nd byte
BnH
4CH
n = MIDI channel number:
0H - FH (Ch.1 - 16)
vv = Vibrato Rate value (relative change):
Vibrato Depth (Controller number 77)
Status
2nd byte
BnH
4DH
n = MIDI channel number:
0H - FH (Ch.1 - 16)
vv = Vibrato Depth Value (relative change):
Vibrato Delay (Controller number 78)
Status
2nd byte
BnH
4EH
n = MIDI channel number:
0H - FH (Ch.1 - 16)
vv = Vibrato Delay value (relative change):
Effect 1 (Reverb Send Level) (Controller number 91)
Status
2nd byte
BnH
5BH
n = MIDI channel number:
0H - FH (Ch.1 - 16)
vv = Reverb Send Level: 00H - 7FH (0 - 127)
Effect 3 (Chorus Send Level) (Controller number 93)
Status
2nd byte
BnH
5DH
n = MIDI channel number:
0H - FH (Ch.1 - 16)
vv = Chorus Send Level: 00H - 7FH (0 - 127)
RPN MSB/LSB (Controller number 100, 101)
Status
2nd byte
BnH
65H
BnH
64H
n = MIDI channel number:
0H - FH (Ch.1 - 16)
mm = upper byte (MSB) of parameter number specified by RPN
ll = lower byte (LSB) of parameter number specified by RPN
<<< RPN >>>
Control Changes include RPN (Registered Parameter Numbers), which are extended
When using RPNs, first the RPN (Controller numbers 100 and 101; they can be sent in any
This device receives the following RPNs.
RPN
Data entry
MSB, LSB
MSB, LSB
00H, 00H
mmH, llH
00H, 01H
mmH, llH
00H, 02H
mmH, llH
7FH, 7FH
---, ---
180
3rd byte
vvH
00H - 7FH (-64 - 0 - +63)
3rd byte
vvH
00H - 7FH (-64 - 0 - +63)
3rd byte
vvH
00H - 7FH (-64 - 0 - +63)
3rd byte
vvH
3rd byte
vvH
3rd byte
mmH
llH
Notes
Pitch Bend Sensitivity
mm:
00H - 18H (0 - 24 semitones)
ll:
ignored (processed as 00H)
Up to 2 octave can be specified in semitone steps.
* In Performance mode, the Part Pitch Bend
Range
parameter
(PERFORM/PART)
change.
Master Fine Tuning
mm, ll: 20 00H - 40 00H - 60 00H (-8192 x 50 /
8192 - 0 - +8192 x50 / 8192 cent)
* In Performance mode, the Part Fine Tune
parameter (PERFORM/PART) will change.
Master Coarse Tuning
mm:
10H - 40H - 70H (-48 - 0 - +48 semitones)
ll:
ignored (processed as 00H)
* In Performance mode, the Part Coarse Tune
parameter (PERFORM/PART) will change.
RPN null
RPN and NRPN will be set as "unspecified".
Once this setting has been made, subsequent
Parameter values that were previously set will
not change.
mm, ll: ignored
Program Change
Status
2nd byte
CnH
ppH
n = MIDI channel number:
pp = Program number: 00H - 7FH (prog.1 - prog.128)
System Exclusive messages
Universal Non-realtime System Exclusive Message" and Data Set 1 (DT1) are the only
System Exclusive messages transmitted by the XV-3080.
Universal Non-realtime System Exclusive Message
Identity Reply Message
Receiving Identity Request Message, the XV-3080 send this message.
Status
Data byte
F0H
7EH, dev, 06H, 02H, 41H, 10H, 01H, 00H, 00H, 00H, 00H, 00H, 00H
F7H
Byte
Explanation
FOH
Exclusive status
7EH
ID number (Universal Non-realtime Message)
dev
Device ID (use the same as the device ID of Roland)
06H
Sub ID#1 (General Information)
02H
Sub ID#2 (Identity Reply)
41H
ID number (Roland)
10H 01H
Device family code
00H 00H
Device family number code
00H 00H 00H 00H
Software revision level
F7H
EOX (End of Exclusive)
Data Transmission
Data set 1
DT1 (12H)
Status
Data byte
F0H
41H, dev, 00H, 10H, 12H, aaH, bbH, ccH, ddH, eeH, ... ffH, sum F7H
Byte Explanation
F0H
Exclusive status
41H
ID number (Roland)
dev
Device ID (dev: 00H - 1FH, Initial value is 10H)
00H
Model ID #1 (XV-3080)
10H
Model ID #2 (XV-3080)
12H
Command ID (DT1)
aaH
Address MSB: upper byte of the starting address of the data to be sent
bbH
Address: upper middle byte of the starting address of the data to be sent
ccH
Address: lower middle byte of the starting address of the data to be sent
ddH
Address LSB: lower byte of the starting address of the data to be sent.
eeH
Data: the actual data to be sent. Multiple bytes of data are transmitted in order
will
starting from the address.
:
:
ffH
Data
sum
Checksum
F7H
EOX (End Of Exclusive)
* The amount of data that can be transmitted at one time depends on the type of data, and
data will be transmitted from the specified starting address and size. Refer to the
Address and Size given in Section 3, "Parameter address map."
* Data larger than 256 bytes will be divided into packets of 256 bytes or less, and each
packet will be sent at an interval of about 20 ms.
0H - FH (Ch.1 - 16)
Status
Status
Advertisement
Table of Contents
