Used for instructions intended to alert the user to the risk of death or severe injury should the unit be used improperly. Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly.
Page 5
• Protect the product from strong impact. (Do not drop it!) • Before installing the ARX-01, you must first always turn off the unit (Fantom-G6/G7/G8) and unplug its power cord. • Install the circuit board only into the specified unit (Fantom-G6/G7/ G8).
ARX-01. Reproduction or duplication of this collection or any of the sound recording contained in the ARX-01, either as they exist on this expansion board or by any means of reformatting, mixing, filtering, re-synthesizing, processing or otherwise editing for use in another product or for re-sale, is strictly prohibited without the express written consent of Roland.
Introduction ... 17 Main Features...17 ARX series SuperNATURAL expansion boards... 17 Roland SuperNATURAL Technology ... 17 ARX-01 Drums... 17 The structure of ARX-01 Drums...18 Creating a Kit ... 19 The basic screen ...19 Selecting a kit ... 19 Group Fader... 19 Saving a kit (on the Fantom-G) ...
2. Orient the board with the slot of your product as shown in the illustration. Slot of the product Latched holders Board (expansion board) Roland logo Non-latched holders Holes that engage the non-latched holders...
Page 9
3. Insert the board into the product’s non-latched board 4. Gently lower the board into place. holders until you hear a click. Connector of board Align board’s holes with holders Connector of product Board Non-latched holders...
Page 10
5. From above, press down on the board at the three locations indicated in the illustration until the latched board holders lock into place. Edge of the board where the logo is affixed Near the cutouts in the board 6. Verify that the latched board holders are locked. 7.
Confirmation after installation After you’ve finished installing the expansion board, you will need to perform the following procedure to confirm the installation. This installation procedure needs to be performed only the first time you power up your device after installing the expansion board. 1.
To remove the board from the product 1. As described in your product’s owner’s manual, expose the slot in which the expansion board was installed. 2. Unlatch the latched board holders. 3. Verify that the two latched board holders are unlocked, then gently pull up the board and disconnect the connector.
être installée. 2. Orienter la carte de façon à ce qu’elle s’aligne avec la vente de l’appareil, comme le montre l’illustration. Fente de l’appareil Supports bloqués Carte (carte d’expansion) Logo Roland Supports non bloqués Trous de retenue des supports non bloqués...
Page 14
3. Insérer la carte dans les supports non bloqués jusqu’à 4. Abaisser la carte délicatement. ce qu’un clic se fasse entendre. Connecteur de la carte Aligner les trous de la carte et les supports Connecteur de l’appareil Carte Supports non bloqués...
Page 15
5. Appuyer sur la carte aux trois points indiqués sur l’illustration jusqu’à ce que les supports se bloquent en place. Bord de la carte où se trouve le logo Près des découpes de la carte 6. S’assurer que les supports de carte sont bien bloqués. 7.
Retirer la carte de l’appareil 1. Suivre les instructions données dans le guide d’utilisation de l’appareil pour dégager la fente où la carte d’expansion a été installée. 2. Débloquer les supports de carte. 3. Vérifier que les deux supports de carte sont débloqués puis tirer délicatement sur la carte et déconnecter le connecteur.
The ARX series SuperNATURAL expansion boards represent a further evolution for Roland’s line of expansion solutions, which began with the SR-JV80 series and SRX series–-they are a completely new type of expansion board. SuperNATURAL technology delivers natural, richly...
Tones A tone is the smallest unit of sound on the ARX-01 Drums board. A tone corresponds to one of the individual instruments (e.g., bass drum or cymbal) that makes up a drum set.
Creating a Kit About this manual • The screen images used in this manual are taken from a Fantom-G with the ARX-01 installed. The various procedures described also assume that you are using the ARX-01 installed in a Fantom-G. • For details on how to move the cursor or edit a value, refer to the owner’s manual for the device in which you’ve actually installed the ARX-01.
Saving a kit (on the Fantom-G) A kit you’ve created is temporary; it will be lost if you select a different kit. If you want to save the kit you’ve edited, proceed as follows. Press [WRITE] on the Fantom-G. Assign a name to the kit. For details on how to assign a name, refer to the Fantom-G owner’s manual.
Selecting a Tone (Tone screen) In the Tone screen you can select the tones that make up the kit. * The Mute Switch in this screen is linked with the Mute Sw (p. 27) of the Tone/Output screen. * The Comp Switch in this screen is linked with the Comp Sw (p. 26) of the Tone/ Comp/EQ screen.
Tone Settings Customizing a tone (Tone/Customize screen) fig.02-001.eps In the Tone/Customize screen you can adjust the sound in the same ways as on an acoustic drum; for example, by choosing the desired shell depth, and by installing muffling (muting). The customizable parameters vary depending on the instrument type to which the tone belongs.
Page 23
E.SNARE Parameter Value Tune -100–+100 Tone -100–+100 Attack Level -100–+100 Snpy Decay -100–+100 Cutoff 0–127 Resonance 0–127 E.TOM, E.HIHAT, E.RIDE, E.OTHER Parameter Value Tune -100–+100 Decay -100–+100 Cutoff 0–127 Resonance 0–127 E.CYMBAL Parameter Value Tune -100–+100 Tone -100–+100 Decay -100–+100 Cutoff 0–127 Resonance...
Flam/Roll settings (Tone/Flam/Roll screen) fig.02-002.eps Here you can apply a fram or roll effect to each tone. You can use note velocity to switch the flam or roll effect on/off. Parameter Value Flam/Roll Velocity 0–127 Boundary between Upper and Lower Threshold Selects the way in which the tone will OFF,...
Page 25
Roll-related parameters fig.roll.eps Delay Rate Rate Offset Note On 2nd Note Parameter Value Description 1–100, Rate Time interval between roll notes note Delay 1–100 Time interval until roll notes begin -100– Difference in strength between note on and the first Offset +100 roll note...
Volume change and tone adjustments (Tone/Comp/EQ screen) fig.02-003.eps Here you can adjust the compressor and equalizer for each tone. * The Tone Level in this screen is linked with the Tone Level param- eter of the Tone/Output screen (p. 27). Compressor This reduces high levels and boosts low levels, making the overall volume more consistent.
Volume adjustment (Tone/Output screen) fig.signal-flow.eps Here you can make settings related to the output of each tone. Signal Flow Input Tone Inst Level Level COMP/EQ Reverb Send Level Parameter Tone Level Output Level Output Assign Reverb Send Level Output Output Mute Sw Level Assign...
Adjusting the volume balance of the tones (Mixer screen) fig.01-006.eps Here you can specify each tone’s Comp Sw (p. 26), Mute Sw (p. 27), Reverb Send Level (p. 27), Pan (p. 27), Tone Level (p. 27), and EQ gain (p. 26). Applying effects (Effects/Routing screen) In the Effects/Routing screen you can make settings for multi-effect...
Effects Parameters” (p. 35). This ability to use MIDI messages to vary the multi-effect parameters in real time is called “multi-effect control.” The ARX-01 expansion board allows you to use four multi-effect controls simultaneously. To use multi-effect control, you need to specify the MIDI message (Source 1–4) that will control the desired parameter (Control Assign...
Page 30
MFX Control Source 1–4 Value Multi-effect control CC01–31, 32(OFF), 33–95 Control Change. PITCH BEND Pitch Bend. AFTERTOUCH Afttertouch. Volume level that is input to the AUDIO Multi-effect MFX Control Sens 1–4 Specifies the depth to which multi-effect control will affect the parameter.
Setting of Reverb (Effects/Reverb screen) In the Effects/Reverb screen you can set the parameters of the reverb. Parameter Value 0 (OFF), 1 (REVERB), Type 2 (SRV ROOM), Type of reverb 3 (SRV HALL), 4 (SRV PLATE) Type: 1 (REVERB) Type of reverb/delay ROOM1: short reverb with high density ROOM2: short reverb with low density ROOM1,...
Choking/muting the drum sound (Ctrl screen) Note number 58 (B 3) is assigned the Choke/Mute function; by pressing this key, you can stop the sound of certain types of instrument that are currently sounding. In the Ctrl screen you can specify the instrument that will be choked/ muted.
3. When the confirmation screen appears, press [F7 (OK)] button. If you decide to cancel, press [F8 (EXIT)] button. * If you’ve installed the ARX-01 in a Fantom-G6/G7/G8, executing a Factory Reset for the Fantom-G6/G7/G8 will reset the expan- sion boards to their factory-set condition.
Multi-Effects List Multi-Effects Types There are 47 types of multi-effect. FILTER (9 types) STEREO EQ p. 35 SPECTRUM p. 36 ENHANCER p. 36 ISOLATOR p. 37 LOW BOOST p. 37 SUPER FILTER p. 38 STEP FILTER p. 39 AUTO WAH p.
Multi-Effects Parameters Each multi-effect has “Control Assign” parameters. These indicate the parameters that can be controlled via “Multi-effect control (Effects/MFX Ctrl screen)” (p. 29). For details on the “note” that can be selected for some parameter, refer to “About Note” (p. 67) In the parameter list below, an indication of “#1”–“#4”...
Page 36
02: SPECTRUM This is a type of filter that modifies the timbre by boosting or cutting the level of specific frequencies. It is similar to an equalizer, but has eight frequency points fixed at locations most useful for adding character to the sound. fig.MFX02 L in Spectrum...
Page 37
04: ISOLATOR This is an equalizer that radically cuts the volume of selected frequencies, allowing you to create special effects cutting the volume in various ranges. fig.MFX04 L in Isolator Low Boost R in Isolator Low Boost Parameter Value Boost/Cut High #3 These boost and cut each of the High, Middle, and Low frequency ranges.
Page 38
06: SUPER FILTER This is a filter with an extremely sharp slope. The cutoff frequency can be varied cyclically. fig.MFX06 L in Super Filter R in Super Filter Parameter Value Filter type Frequency range that will pass through each filter LPF: frequencies below the cutoff LPF, BPF, HPF, Filter Type #1...
Page 39
07: STEP FILTER This is a filter whose cutoff frequency can be modulated in steps. You can specify the pattern by which the cutoff frequency will change. fig.MFX07 L in Step Filter R in Step Filter Parameter Value 0.05–10.00 Hz, Rate #1 Rate of modulation note...
Page 40
09: HUMANIZER Adds a vowel character to the sound, making it similar to a human voice. fig.MFX09 L in Overdrive Formant R in Parameter Value Drive Sw OFF, ON Drive 0–127 Vowel1 #1 a, e, i, o, u Vowel2 #2 a, e, i, o, u 0.05–10.00 Hz, Rate #3...
Page 41
11:STEREO PHASER This is a stereo phaser. fig.MFX11 L in Phaser Phaser R in Parameter Value Mode 4, 8 stage Number of stages in the phaser Selects whether the left and right phase of the modulation are the same or opposite each other.
Page 42
Parameter Value 0–127 Level of the phase-shifted sound Low Gain -15– +15 dB Gain of the low frequency range High Gain -15– +15 dB Gain of the high frequency range Level 0–127 Output level 13: RING MODULATOR Description This is an effect that applies amplitude modulation (AM) to the input signal, producing bell-like sounds.
Page 43
14: TREMOLO Cyclically modulates the volume to add tremolo to the sound. fig.MFX14 L in Tremolo 2-Band EQ R in Tremolo 2-Band EQ Parameter Value Modulation Wave TRI: triangle wave Modulation Wave TRI, SQR, SIN, SQR: square wave SAW1, SAW2 SIN: sine wave SAW1: sawtooth wave (upward) SAW2: sawtooth wave (downward)
Page 44
16: ROTARY The Rotary effect simulates the sound of the rotary speakers often used with the classic electric organs. Since the movement of the high-range and low- range rotors can be set independently, the unique characteristics of these speakers can be simulated quite accurately. This effect is most suitable for electric organ Patches.
Page 45
17: HEXA-CHORUS Uses a six-phase chorus (six layers of chorused sound) to give richness and spaciousness to the sound. fig.MFX17 L in Balance D Hexa Chorus R in Balance D Parameter Value Pre Delay 0.0–100.0 ms Adjusts the time until chorusing is heard. 0.05–10.00 Hz, Rate #1 Frequency of modulation...
Page 46
19: SPACE-D This is a multiple chorus that applies two-phase modulation in stereo. It creates no audible modulation, yet produces a transparent chorus effect. fig.MFX19 Balance D L in Space D Space D R in Balance D Parameter Value Adjusts the time until the chorus sound is Pre Delay 0.0–100.0 ms heard.
Page 47
21: STEREO FLANGER This is a stereo flanger. It produces a metallic resonance that rises and falls somewhat like a jet airplane taking off or landing. A filter is provided so that you can adjust the timbre of the flanged sound. fig.MFX21 Balance D L in...
Page 48
22: STEP FLANGER This is a flanger in which the flanger pitch changes in steps. The speed at which the pitch changes can also be specified in terms of a note value based on a specified tempo. fig.MFX22 Balance D L in Step Flanger Step Flanger...
Page 49
25: GUITAR AMP SIM (Guitar Amp Simulator) This is an effect that simulates the sound of a guitar amplifier. fig.MFX25 L in Pre Amp Speaker R in Parameter Value Pre Amp Sw OFF, ON Turns the amp switch on/off. JC-120, Clean Twin, Match Drive, BG Lead,...
Page 50
Specifications for each Speaker Type The speaker column indicates the diameter of each speaker unit (in inches) and the number of units. Type Cabinet Small1 small open-back enclosure Small2 small open-back enclosure Middle open back enclosure JC-120 open back enclosure Built In 1 open back enclosure Built In 2...
Page 51
27: LIMITER Compresses signals that exceed a specified volume level, preventing distortion from occurring. fig.MFX27 L in Limiter 2-Band EQ R in Limiter 2-Band EQ Parameter Value Adjusts the time after the signal volume Release #1 0–127 falls below the Threshold Level until com- pression is no longer applied.
Page 52
Parameter Value Shuffle 0–127 Level 0–127 Step 01–16 0–127 29: GATE Description Cuts the reverb’s delay according to the volume of the sound sent into the Timing of volume changes in levels for even-numbered steps (step 2, step 4, step effect.
Page 53
30: LOFI NOISE (Lo-Fi Noise) In addition to a lo-fi effect, this adds various types of noise such as white noise and disc noise. fig.MFX30 L in Lo-Fi Noise Gen. Lo-Fi R in Parameter Value Degrades the sound quality. The sound LoFi Type #1 1–9 quality grows poorer as this value is in-...
Page 54
31: LOFI COMPRESS (Lo-Fi Compress) This is an effect that intentionally degrades the sound quality for creative purposes. fig.MFX31 L in Compressor R in Compressor Parameter Value Pre Filter 1–6 Type #2 LoFi Type #1 1–9 Post Filter OFF, LPF, HPF Type Post Filter Cutoff 200–8000 Hz...
Page 55
33: TELEPHONE fig.MFX33 L in Telephone R in Telephone Parameter Value Voice Quality #1 0–15 Audio quality of the telephone voice Treble #2 -15– +15 dB Bandwidth of the telephone voice D100:0– Volume balance between the direct Balance #3 D0:100W sound (D) and the effect sound (W) Level 0–127...
Page 56
Description A virtual tape echo that produces a realistic tape delay sound. This Depth of distortion simulates the tape echo section of a Roland RE-201 Space Echo. Frequency response of the playback sys- Decreasing this value will produce the im-...
Page 57
Parameter Value Speed of wow/flutter (complex variation Wow/Flutter Rate 0–127 in pitch caused by tape wear and rota- tional irregularity) Wow/Flutter 0–127 Depth of wow/flutter Depth Echo Level 0–127 Volume of the echo sound Direct Level 0–127 Volume of the original sound 36: FBK PITCH SHIFTER (Feedback Pitch Shifter) Description This allows the pitch-shifted sound to be fed back into the effect.
Page 58
37: 2Vo PITCH SHIFTER (2-Voice Pitch Shifter) Shifts the pitch of the original sound. This 2-voice pitch shifter has two pitch shifters, and can add two pitch-shifted versions of the original sound. fig.MFX37 L in Level Balance A PanA R 2Voice Pitch Shifter PanB L Level Balance B...
Page 59
39: STEREO DELAY This is a stereo delay. When Feedback Mode is NORMAL: Balance D L in Delay Feedback Feedback Delay R in Balance D When Feedback Mode is CROSS: fig.MFX39b Balance D L in Delay Feedback Feedback Delay R in Balance D Parameter Feedback Mode...
Page 60
40: MODULATION DELAY Adds modulation to the delayed sound. When Feedback Mode is NORMAL: fig.MFX40a Balance D L in Delay Modulation Feedback Feedback Delay Modulation R in Balance D When Feedback Mode is CROSS: fig.MFX40b Balance D L in Delay Modulation Feedback Feedback...
Page 61
41: TRIPLE TAP DELAY Produces three delay sounds; center, left and right. fig.MFX41 Balance D L in Left Tap Triple Tap Delay Center Tap Feedback Right Tap R in Balance D Parameter Value Left #1 0–4000 ms, Adjusts the time until the delay sound is Center #2 note heard.
Page 62
Parameter Value 200–8000 HF Damp Hz, BYPASS D100:0W– Balance D0:100W Level 0–127 43: MULTI TAP DELAY Description This effect provides four delays. Each of the Delay Time parameters can be Adjusts the frequency above which sound fed back to the effect is filtered out. If you set to a note length based on the selected tempo.
Page 63
44: REVERSE DELAY Adds the reverse of the input sound as a delay. fig.MFX44 L in Rev. Delay Delay Feedback 1 Feedback 4 R in Parameter Value Volume level at which the reverse delay Threshold 0–127 begins Delay 1–4 0-2000 ms, Adjusts the time until Delays 1–4 are (Delay 1 #1) note...
Page 64
Parameter Value Low Gain -15– +15 dB High Gain -15– +15 dB D100:0W– Balance #4 D0:100W Level 0–127 46: TIME CONTROL DELAY Description This lets you smoothly vary the delay time. As the delay time is varied, the Gain of the low frequency range pitch will change correspondingly;...
Page 65
47: TIME SKIP DELAY A delay that changes the delay time in stair-step fashion. fig.MFX47 L in Balance D Time Skip Delay Feedback R in Balance D Parameter Value Delay #1 0–4000 ms, note Adjusts the time until the delay is heard. 0.05–10.0 Hz, Frequency at which the delay time will Skip Rate...
About the STEP RESET function 07:STEP FILTER 28:SLICER The above two types contain a sixteen-step sequencer. For these effect types, you can use multi-effect control (“Multi-effect control (Effects/MFX Ctrl screen)” (p. 29)) to reset the step sequence to its beginning. To do this, set the Control Assign setting for that effect type to “Step Reset.”...
About Note Some parameters (such as Rate or Delay Time) can be set in terms of a note value instead of a time value. Such parameters provide a Sync switch (Sync SW) that allows you to switch between setting the parameter as a note value or as a numerical value. If you want to set it as a note value, set the Sync SW to ON.
Specifications ARX-01 DRUMS Maximum Polyphony 128 voices (varies according to the sound generator load) Parts 1 part User Memory Drum Kits: 50 (including pre-loaded kits) Effects EQ/COMP: 24 systems (1 system par instrument) Multi-Effects(MFX): 1 system, 47 types Reverb: 1 system, 4 types...
Page 71
Tone Customize ... 22 Select ... 21 Tone Init ... 33 Tone screen ... 21 Tone/Comp/EQ screen ... 26 Tone/Customize screen ... 22 Tone/Output screen ... 27 Type ... 31 Utility screen ... 33...
Page 72
This product complies with the requirements of EMC Directive 2004/108/EC. FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 73
For the USA DECLARATION OF CONFORMITY Compliance Information Statement Model Name : ARX-01 Type of Equipment : Expansion Board Responsible Party : Roland Corporation U.S. Address : 5100 S. Eastern Avenue, Los Angeles, CA 90040-2938 Telephone : (323) 890-3700...
Page 76
Information When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as shown below. AFRICA ASIA EGYPT CHINA Al Fanny Trading Office Roland Shanghai Electronics 9, EBN Hagar Al Askalany Co.,Ltd. Street, 5F.
Page 77
Bldg., Achrafieh, P.O.Box: 16- 5857 No. 14, Ground Floor, Dubai, Beirut, LEBANON U.A.E. TEL: (01) 20-1441 TEL: (04) 3360715 As of Oct. 1, 2007 (ROLAND) NORTH AMERICA CANADA Roland Canada Ltd. (Head Office) 5480 Parkwood Way Richmond B. C., V6V 2M4...
トーンを選ぶ(Tone 画面) fig.01-004.eps Tone 画面では、キットを構成するトーンを選びます。 ※ この画面にある MUTE スイッチは、Tone/Output 画面の Mute Sw(P.99)に連動しています。 ※ この画面にある COMP スイッチは、Tone/Comp/EQ 画面 の Comp Sw(P.98)に連動しています。 Tone 画面が表示されている状態で鍵盤を弾くと、Current Tone が自動的に切り替わります。 パラメーター 設定値 トーン番号を表示します。設定 Current Tone Tone 01 ∼ 値を変更してカレント・トーン (カレント・トーン) Tone 24 を変えることができます。 パラメーター Inst Type Inst Number Fader Group Layer Tone...
マルチエフェクト・パラメーター 各マルチエフェクトには「Control Assign」 (コントロール・アサイ ン)というパラメーターがあります。これは『マルチエフェクト・コ ントロール (Effects / MFX Ctrl 画面) 』 (P.101)によってコント ロールされるパラメーターを指定します。 設定値「音符」について、詳しくは、 『音符について』 (P.139)を参 照してください。 以下のパラメーター・リストで、初期状態でコントロール・アサイン に指定されているパラメーターには、パラメーター名の後ろに「#1」 ∼「#4」が付いています。 01:STEREO EQ(ステレオ・イコライザー) 低域、中域× 2、高域の音質を調節します。 fig.02-001m L in 4-Band EQ R in 4-Band EQ パラメーター 設定値 Low Freq 200、400Hz 低域の基準周波数 Low Gain #1 -15 ∼...
Page 108
02:SPECTRUM(スペクトラム) 特定の周波数のレベルを増減させて音色を変えます。 音色のクセをつけるのに最適な 8 つの周波数が決められているので、 イ コライザーより特徴のある音が作れます。 fig.02-005m L in Spectrum R in パラメーター 設定値 0.5、1.0、2.0、 4.0、8.0 L64 ∼ 63R Level 0 ∼ 127 Band 1 (250Hz) Band 2 (500Hz) #1 Band 3 (1kHz) #2 Band 4 (1.25kHz) -15 ∼ +15dB Band 5 (2kHz) #3 Band 6 (3.15kHz) Band 7 (4kHz) #4...
13:RING MODULATOR (リング・モジュレーター) 入力信号に振幅変調(AM 変調)をかけることによりベルのような音を 出すことができます。入力音の音量により、変調周波数を変化させるこ ともできます。 fig.02-044m L in Ring Mod 2-Band EQ R in Ring Mod 2-Band EQ パラメーター 設定値 Frequency #1 0 ∼ 127 Sens #2 0 ∼ 127 Polarity UP、DOWN Low Gain -15 ∼ +15dB High Gain -15 ∼...
Page 115
15:AUTO PAN(オート・パン) 音の定位を周期的に変化させます。 fig.02-063am L in Auto Pan 2-Band EQ R in Auto Pan 2-Band EQ パラメーター 設定値 定位の変化のしかた TRI:三角波 Modulation TRI、SQR、SIN、 SQR:矩形波 Wave #1 SAW1、SAW2 SIN:正弦波 SAW1:のこぎり波(上昇) SAW2:のこぎり波(下降) 0.05 ∼ Rate # 2 エフェクトのかかる周期 10.00Hz、音符 Depth #3 0 ∼ 127 エフェクトのかかる深さ...
Page 116
17:HEXA-CHORUS(ヘキサ・コーラス) 音に厚みと広がりを与える 6 相コーラス(ディレイ・タイムの異なる 6 つのコーラス音が重なる)です。 fig.02-011m L in Balance D Hexa Chorus R in Balance D パラメーター 設定値 Pre Delay 0.0 ∼ 100.0ms 0.05 ∼ Rate #1 10.00Hz、音符 Depth #2 0 ∼ 127 Pre Delay 0 ∼ 20 Deviation Depth Deviation -20 ∼...
19:SPACE-D(スペース D) 2 相のモジュレーションをステレオでかける多重コーラスです。変調感 はありませんが、透明感のあるコーラス効果が得られます。 fig.02-013m Balance D L in Balance W Space D Balance W Space D R in Balance D パラメーター 設定値 原音が鳴ってからコーラス音が鳴るま Pre Delay 0.0 ∼ 100.0ms での遅延時間 0.05 ∼ Rate #1 揺れの周期 10.00Hz、音符 Depth #2 0 ∼ 127 揺れの深さ...
21:STEREO FLANGER (ステレオ・フランジャー) ステレオ仕様のフランジャーです。 ジェット機の上昇音/下降音のような金属的な響きが得られます。フィ ルターを使ってフランジャー音の音質を調節できます。 fig.02-015m Balance D L in Flanger Flanger R in Balance D パラメーター 設定値 Filter Type OFF、LPF、HPF Cutoff Freq 200 ∼ 8000Hz Pre Delay 0.0 ∼ 100.0ms 0.05 ∼ Rate #1 10.00Hz、音符 Depth #2 0 ∼ 127 Phase 0 ∼...
Page 119
22:STEP FLANGER (ステップ・フランジャー) フランジャー音 のピッチが段階的 に変化します。ピッチ 変化の周期は、 特定のテンポに対する音符の長さで設定することもできます。 fig.02-016m Balance D L in Step Flanger Feedback Feedback Step Flanger R in Balance D パラメーター 設定値 原音が鳴ってからフランジャー音が鳴 Pre Delay 0.0 ∼ 100.0ms るまでの遅延時間 0.05 ∼ Rate #1 揺れの周期 10.00Hz、音符 Depth 0 ∼ 127 揺れの深さ...
Page 120
24:DISTORTION(ディストーション) ディス トーションはオーバ ードライブよりも 激しい歪みが得られ ます。 設定項目は「23:OVERDRIVE」と同じです。 fig.02-003m L in Distortion Simulator R in 25:GUITAR AMP SIM (ギター・アンプ・シミュレーター) ギター・アンプをシミュレートします。 fig.02-078m L in Pre Amp Speaker R in パラメーター 設定値 Pre Amp Sw OFF、ON 1 1 1 1 2 2 2 2 0 0 0 0 L out Pan L Pre Amp Type...
Page 122
27:LIMITER(リミッター) 指定の音量より大きな音を圧縮し、音の歪みを抑えます。 fig.02-056m L in Limiter 2-Band EQ R in Limiter 2-Band EQ パラメーター 設定値 Release #1 0 ∼ 127 Threshold #2 0 ∼ 127 1.5:1、2:1、 Ratio #3 4:1、100:1 Post Gain #4 0 ∼ 18dB Low Gain -15 ∼ +15dB High Gain -15 ∼...
30:LOFI NOISE(ローファイ・ノイズ) ローファイ効果に加えて、ホワイト・ノイズ、ディスク・ノイズなどの ノイズを発生させます。 fig.02-051m L in Lo-Fi Noise Gen. Lo-Fi R in パラメーター 設定値 LoFi Type #1 1 ∼ 9 Post Filter Type OFF、LPF、HPF Post Filter 200 ∼ 8000Hz Cutoff W/P Noise Type WHITE、PINK 200 ∼ W/P Noise LPF 8000Hz、...
31:LOFI COMPRESS (ローファイ・コンプレス) 音質を荒くします。 fig.02-051m L in Compressor Lo-Fi R in Compressor Lo-Fi パラメーター 設定値 Pre Filter Type 1 ∼ 6 LoFi を通る前のフィルターの種類 音質を粗くします。値が大きいほど音 LoFi Type #1 1 ∼ 9 質が粗くなります。 LoFi を通った後のフィルターの種類 OFF:フィルター未使用 Post Filter Type OFF、LPF、HPF LPF:高域をカット HPF:低域をカット Post Filter 200 ∼...
Page 129
37:2Vo PITCH SHIFTER (2 ボイス・ピッチ・シフター) 原音のピッチをずらします。 ピッチをずらした 2 つの音を原音に重ねて 鳴らすことができます。 fig.02-022m Balance D L in Level Balance A PanA L PanA R 2Voice Pitch Shifter PanB L PanB R Level Balance B R in Balance D パラメーター 設定値 値を大きくすると反応が遅くなり、 Mode 1、2、3、4、5 音揺れが少なくなります。...
38:GATED REVERB(ゲート・リバーブ) リバーブ音を途中でカットするリバーブです。 fig.02-025m L in Balance D Gated Reverb R in Balance D パラメーター 設定値 NORMAL、 Type #1 REVERSE Pre Delay #2 0.0 ∼ 100.0ms Time #3 5 ∼ 500ms L64 ∼ 63R Low Gain -15 ∼ +15dB High Gain -15 ∼...
Page 133
42:QUADRUPLE TAP DELAY (クアドラプル・タップ・ディレイ) 4 つのディレイ音を鳴らせます。 fig.02-020am L in Delay 1 Feedback Delay 2 Quadruple Tap Delay Delay 3 Delay 4 R in 各ディレイ音の定位 fig.02-020bm パラメーター Delay 1 ∼ 4 #1 ∼ # 4 Level 1 ∼ 4 Balance D Feedback L out Balance W...
Page 134
43:MULTI TAP DELAY (マルチ・タップ・ディレイ) 4 つのディレイ音を鳴らせます。ディレイ・タイムは指定のテンポに対 する音符の長さで設定することもできます。また、各ディレイ音の定位 やレベルを設定することができます。 fig.02-045m Balance D L in Feed Delay 1 back Delay 3 Multi Tap Delay Delay 4 Delay 2 R in Balance D 1 1 1 1 3 3 3 3 4 4 4 4 パラメーター...