Roland JUNO-G Owner's Manual page 132

Adding Effects
01: EQUALIZER
This is a four-band stereo equalizer (low, mid x 2, high).
fig.MFX-01
L in
4-Band EQ
R in
4-Band EQ
Parameter Value
Low Freq 200, 400 Hz
Low Gain # -15– +15 dB
Mid1 Freq 200–8000 Hz
Mid1 Gain -15– +15 dB
Mid1 Q 0.5, 1.0, 2.0, 4.0, 8.0
Mid2 Freq 200–8000 Hz
Mid2 Gain -15– +15 dB
Mid2 Q 0.5, 1.0, 2.0, 4.0, 8.0
High Freq 2000, 4000, 8000 Hz
High Gain # -15– +15 dB
Level # 0–127
02: SPECTRUM
This is a stereo spectrum. Spectrum is a type of filter which modifies
the timbre by boosting or cutting the level at specific frequencies.
fig.MFX-02
L in Spectrum
R in
Spectrum
Parameter Value
Band1 (250Hz) -15– +15 dB
Band2 (500Hz)
Band3 (1000Hz)
Band4 (1250Hz)
Band5 (2000Hz)
Band6 (3150Hz)
Band7 (4000Hz)
Band8 (8000Hz)
Q 0.5, 1.0, 2.0, 4.0, 8.0
Level # 0–127
03: ISOLATOR
This is an equalizer which cuts the volume greatly, allowing you to
add a special effect to the sound by cutting the volume in varying
ranges.
fig.MFX-03
L in Low Boost
Isolator
R in
Isolator Low Boost
132
L out
R out
Explanation
Frequency of the low range
Gain of the low range
Frequency of the middle
range 1
Gain of the middle range 1
Width of the middle range 1
Set a higher value for Q to
narrow the range to be af-
fected.
Frequency of the middle
range 2
Gain of the middle range 2
Width of the middle range 2
Set a higher value for Q to
narrow the range to be af-
fected.
Frequency of the high range
Gain of the high range
Output Level
L out
R out
Explanation
Gain of each frequency band
Simultaneously adjusts the
width of the adjusted ranges for
all the frequency bands.
Output Level
L out
R out
Parameter Value
Boost/ -60– +4 dB
Cut Low #
Boost/
Cut Mid #
Boost/
Cut High #
Anti Phase OFF, ON
Low Sw
Anti Phase 0–127
Low Level
Anti Phase OFF, ON
Mid Sw
Anti Phase 0–127
Mid Level
Low Boost Sw OFF, ON
Low Boost 0–127
Level
Level 0–127
04: LOW BOOST
Boosts the volume of the lower range, creating powerful lows.
fig.MFX-04
L in
Low Boost 2-Band EQ
R in
Low Boost
2-Band EQ
Parameter Value
Boost 50–125 Hz
Frequency #
Boost Gain # 0– +12 dB
Boost Width WIDE, MID,
NARROW
Low Gain -15– +15 dB
High Gain -15– +15 dB
Level 0–127
05: SUPER FILTER
This is a filter with an extremely sharp slope. The cutoff frequency
can be varied cyclically.
fig.MFX-05
L in
Super Filter
R in
Super Filter
Parameter Value
Filter Type LPF, BPF,
HPF, NOTCH
Explanation
These boost and cut each of the High,
Middle, and Low frequency ranges.
At -60 dB, the sound becomes in-
audible. 0 dB is equivalent to the
input level of the sound.
Turns the Anti-Phase function on and
off for the Low frequency ranges.
When turned on, the counter-
channel of stereo sound is inverted
and added to the signal.
Adjusts the level settings for the Low
frequency ranges.
Adjusting this level for certain fre-
quencies allows you to lend em-
phasis to specific parts. (This is
effective only for stereo source.)
Settings of the Anti-Phase function
for the Middle frequency ranges
The parameters are the same as for
the Low frequency ranges.
Turns Low Booster on/off.
This emphasizes the bottom to cre-
ate a heavy bass sound.
Increasing this value gives you a
heavier low end.
* Depending on the Isolator and fil-
ter settings this effect may be hard
to distinguish.
Output Level
L out
R out
Explanation
Center frequency at which the lower
range will be boosted
Amount by which the lower range
will be boosted
Width of the lower range that will be
boosted
Gain of the low frequency range
Gain of the high frequency range
Output level
L out
R out
Explanation
Filter type
Frequency range that will pass
through each filter
LPF: frequencies below the cutoff
BPF: frequencies in the region of the
cutoff
HPF: frequencies above the cutoff
NOTCH: frequencies other than the
region of the cutoff