Canon imageFORMULA DR-X10C Service Manual page 6

11. Operation Panel .............................. 3-12
III. BASE UNIT-1 (ELECTRICAL SYSTEM)
.......................................................... 3-13
1. Control PCB...................................... 3-13
2. Power Supply PCB........................... 3-14
3. Main Motor........................................ 3-15
4. Main Motor PCB ............................... 3-16
5. Exhaust Fan ..................................... 3-17
6. Tray Detection PCB.......................... 3-17
7. Tray Drive Unit.................................. 3-18
8. Pickup Tray Motor ............................ 3-19
9. Separation Motor .............................. 3-19
10. Ultrasonic Drive PCB ...................... 3-20
11. Eject Unit......................................... 3-21
12. Eject Motor ...................................... 3-21
13. Eject PCB........................................ 3-22
14. Platen Motor (Lower) ...................... 3-22
IV. BASE UNIT-2 (FEED SYSTEM) ........... 3-24
1. Entrance Lower Guide Unit .............. 3-24
2. Platen Roller (Lower)........................ 3-24
3. Registration Roller............................ 3-25
4. Reading Roller (Front)...................... 3-26
5. Reading Roller (Center) ................... 3-27
6. Reading Roller (Rear) ...................... 3-28
7. U-Turn Roller A................................. 3-28
8. U-Turn Roller B................................. 3-29
9. Eject Roller ....................................... 3-30
10. Belt (Right) ...................................... 3-30
11. Belt (Left)......................................... 3-31
V. BASE UNIT-3 (READING SYSTEM) .... 3-32
1. Reading Unit (Lower) ....................... 3-32
2. Reading PCB.................................... 3-33
3. Shading Motor .................................. 3-35
4. CIS Unit ............................................ 3-36
5. Reading Holder ................................ 3-38
6. Blower............................................... 3-38
7. Frame Detection Unit ....................... 3-39
VI. UPPER UNIT-1 (EXTERNAL COVERS)
.......................................................... 3-40
1. Entrance Upper Unit......................... 3-40
COPYRIGHT © CANON ELECTRONICS INC. 2008
VII. UPPER UNIT-2 (ELECTRICAL SYSTEM)
VIII. UPPER UNIT-3 (FEED SYSTEM)......... 3-51
IX. UPPER UNIT-4 (READING SYSTEM).. 3-58
X.
I.
CANON DR-X10C FIRST EDITION
2. Pickup Roller Cover.......................... 3-40
3. Upper Front Cover............................ 3-41
4. Entire Upper Unit .............................. 3-42
.......................................................... 3-46
1. Main Drive PCB ................................ 3-46
2. Staple PCB ....................................... 3-47
3. Ultrasonic Sensor PCB..................... 3-48
4. Pickup Unit Motor ............................. 3-49
5. Platen Motor ..................................... 3-50
1. Platen Roller ..................................... 3-51
2. Registration Roller ........................... 3--51
3. Reading Roller (Front) ...................... 3-52
4. Reading Roller (Center) ................... 3-53
5. Reading Roller (Rear)....................... 3-53
6. U-Turn Rollers .................................. 3-54
7. Eject Roller ....................................... 3-55
8. Pickup Unit ....................................... 3-55
9. Reverse Roller.................................. 3-56
10. Roller Holder ................................... 3-56
1. Reading Unit..................................... 3-58
2. Reading PCB.................................... 3-59
3. Blower............................................... 3-60
4. Reading Holder................................. 3-61
OPTION................................................. 3-62
1. Post-Imprinter ................................... 3-62
2. Pre-Imprinter..................................... 3-64
CHAPTER 4
INSTALLATION &
MAINTENANCE
INSTALLATION ....................................... 4-1
1. Choosing Location.............................. 4-1
2. Unpacking And Installation ................. 4-2
3. Pre-imprinter Installation Procedure... 4-9
4. Post-imprinter Installation Procedure
........................................................ 4-12