Programming Batch Transmission - Muratec MFX-1500 Operating Instructions Manual

Beyond the bas cs
9.
There's a choice to make. Instruct your fax to carry out this delayed
command in one of the following ways:
Option 1:
Perform the command once at a certain time on a certain day of
the month (For example, "Do this at 5:05
To select this option, use the numeric keypad to enter the
date and time when the fax should perform the command:
Delayed
Enter Time: 30/17:05
Option 2:
Perform the command at a certain time each day you press
the key. (For example, "Do this at 5:05
To select this option, use the numeric keypad to enter 0, 0
(i. e., 00), and then the time when the fax could perform
the command:
Delayed
Enter Time: 00/17:05
10.
Press , .
ENTER ENTER
11. The display now shows the next programmable one-touch key.
If you do not wish to enter or change any other key's programming, press
to return your machine to its usual standby mode.
STOP
If you do wish to enter or change this key's programming, go back to step 3.
If you wish to enter or change another key's programming, go back to step 2.

Programming batch transmission

Note: To erase a programmable one-touch key, refer to page 2.70.
Note: For this operation to work, two things must be true:
The batch box must exist on your machine. (If necessary, see "Creating
or modifying a batch box," pages 2.24–2.25.)
You must know the batch box's one-digit number (1–5).
To program a batch transmission into a programmable one-touch key:
1. Change to the Fax mode then press
either shows:
Select Program No.
73:No Number Stored
. . . or indicates a command already is programmed into this key.
Note: To program a key into which a command other than batch
transmission has already been programmed, you must first erase
the key (see page 2.70). Then, return to these instructions and
select that key.
2.66
on the 30th.")
PM
today.")
PM
, , 1, . The display
PROGRAM C ENTER
If a batch transmission is already programmed into this key, you
can change the batch box number, in step 6. (But you can't
change the key to another kind of command. To do that, you must
first erase the key and then program that key as described
elsewhere in this section.)
If 73 is the key you want to program, skip to step 4. (However, our
examples from here will say "75" rather than "73. "
2. Select the key in which you want to program a command or change a
previously stored command — if necessary, turn the fliptab to see it, as
described earlier — and then press it. Here, we've selected 75.
Select Program No.
75:No Number Stored
3. If you change your mind and wish to select a different programmable one-
touch key, go back to step 2 before going on to step 4.
4.
Do not enter any characters here (if you do, you can't program a batch
transmission into this key). Instead, only press
step 5.
75:Fax Number
_
Note: Again, do not enter any characters here. If you have already
accidentally entered any characters here, press
times as needed to erase all of them before proceeding to step 5.
Note: If this key already holds a batch transmission, skip to step 6.
5.
Press
COMMUNICATION OPTIONS
display shows:
Batch Tx
Enter Box No. _
6.
Use the numeric keypad to enter the one-digit number for the batch box
you wish to assign to this key. Here, we've entered 5:
Batch Tx
Enter Box No. 5_
Note: To change an identifier already entered, press
Then re-enter until the number is just as you want it.
7. Press .
ENTER
and then proceed to
ENTER
as many
CANCEL
five times and then press . The
ENTER
to erase it.
CANCEL