Timer Recording - Panasonic OmniVision PV-DF2035-K Operating Instructions Manual

Timer Recording

Set up to 8 Programs
You can set up to 8 programs to be recorded while you are
away.
1
Press PROG to display SET
PROGRAM screen.
2
Press ▲▼ to select "TIMER
PROGRAMMING."
3
Press SET to display screen.
• If a program is already in memory, press ▲▼, and SET to select an
unused program number.
4
Press ▲▼ to select and SET or
◄► to set the recording DATE.
• 1~31 = One time
• DAILY (day) = Monday~Friday
• WEEKLY (SU~SA) = Same time once a
week
Repeat step 4 to set:
• Start time, stop time
• Channel (or LINE for outside source)
• Speed (SP, SLP)
Today's Date
5
Press PROG to set the
program. To Enter More
Programs, press ▲▼ to select
and SET to set a blank program
number, and then repeat step
4.
6
Press PROG twice to exit this mode.
• If you're using a cable box, make sure that it is tuned to the desired
channel and the power is left on for timer recording.
• PROG TIMER indicator lights up on the unit.
26
Review, Replace or
Clear Program Con tents :
(Recording is not in progress)
1
2
SET PROGRAM
TIMER PROGRAMMING
ON TIMER
SLEEP TIMER: 0
3
SELECT: SET:SET
END :PROG
4
P DT START STOP CH SPD
1 -- --:-- --:-- -- --
2 -- --:-- --:-- -- --
3 -- --:-- --:-- -- --
4 -- --:-- --:-- -- --
SELECT: SET:SET
END :PROG
Example:
7 8
WEEKLY
(SA)
5
WEEKLY
(MO)
31 Notes:
• 2 minutes before Timer recording is performed, "PLEASE PREPARE FOR
WEEKLY
1
(SU)
• If the start times of two programs overlap, the lower numbered program
• If the start time for a Timer Recording comes up during a normal recording
DAILY
(day)
6
• If there is a power interruption of more than one minute, the recording may
• If "INCOMPLETE" appears after all items have been set, check all entries
P DT START STOP CH SPD
1 10 9:00a12:00p 08 SP
2 -- --:-- --:-- -- --
3 -- --:-- --:-- -- --
4 -- --:-- --:-- -- --
Cancel a Timer Re cord ing:
SET COMPLETED
CANCEL:ADD/DLT
(Recording is in progress)
SELECT: SET:SET
END :PROG
1
Press PROG to display SET
PROGRAM screen.
Press ▲▼ to select "TIMER
PROGRAMMING."
Press SET to display screen.
Press ▲▼ to select the desired
program.
To Replace program...
a. Press SET to display.
b. Press ▲▼ to select and press
SET or ◄► to set new program
contents.
c. Press PROG.
To Clear program...
Press ADD/DLT.
Press PROG twice to exit this mode.
TIMER REC" appears. Be sure a cassette with record tab is loaded and
the unit is in Stop mode.
will have priority.
or One Touch Recording (page 25), the Timer Recording will not be
performed.
not be performed or continued.
and make necessary corrections.
Hold down STOP for a few seconds to cancel the
Timer Recording.
• Any future daily or weekly recordings will be performed as
programmed.
SET PROGRAM
TIMER PROGRAMMING
ON TIMER
SLEEP TIMER: 0
SELECT: SET:SET
END :PROG
P DT START STOP CH SPD
1 10 9:00a12:00p 08 SP
2day 11:00a11:30a125 SP
3 12 8:00p 9:30p L1 SLP
4 -- --:-- --:-- -- --
CANCEL:ADD/DLT
SELECT: SET:SET
END :PROG
P DT START STOP CH SPD
1 10 9:00a12:00p 08 SP
2day 11:00a11:30a125 SP
3 12 8:00p 9:30p L1 SLP
4 -- --:-- --:-- -- --
CANCEL:ADD/DLT
SELECT: SET:SET
EXIT :PROG
P DT START STOP CH SPD
1 -- --:-- --:-- -- --
2day 11:00a11:30a125 SP
3 12 8:00p 9:30p L1 SLP
4 -- --:-- --:-- -- --
SELECT: SET:SET
END :PROG