Total Bandwidth; Communication Bit Rate - Sony IPELA PCS-XG100 Operating Instructions Manual

On: Select to configure the IP settings for a
point-to-point connection and
multipoint connection individually.
Note
The setting items and page numbers in the IP:
Mode page vary according to the setting of
"Individual Settings".
Communication
IP: Mode

Total Bandwidth

Allows you to select the total bandwidth to
be used with this system.
In multipoint connection, the total
bandwidth of all points is displayed.
You can select from among 128Kbps,
384Kbps, 512Kbps, 768Kbps, 1Mbps,
2Mbps, 3Mbps, 4Mbps, 5Mbps, 6Mbps,
7Mbps, 8Mbps, 9Mbps, 10Mbps, 11Mbps,
12Mbps, 13Mbps, 14Mbps, 15Mbps,
16Mbps, and Other.
Notes
• In multipoint connection, the actual
Communication Bit Rate for each point is
automatically adjusted so as not to exceed
"Total Bandwidth".
• The 5Mbps, 6Mbps, 7Mbps, 8Mbps, 9Mbps,
10Mbps, 11Mbps, 12Mbps, 13Mbps,
14Mbps, 15Mbps, and 16Mbps settings are
not available on the PCS-XG77/XG77S.

Communication Bit Rate

Allows you to select the communication bit
rate per point.
When "Individual Settings for
Transmission/Reception" or "Individual
Settings for Point-to-Point/Multipoint" on
the IP page is set to "On", you can set this
item for transmission and reception, and
point-to-point and multipoint connections
individually.
You can select from among 128Kbps,
384Kbps, 512Kbps, 768Kbps, 1Mbps,
2Mbps, 3Mbps, 4Mbps, 5Mbps, 6Mbps,
7Mbps, 8Mbps, 9Mbps, 10Mbps, 11Mbps,
12Mbps, 13Mbps, 14Mbps, 15Mbps,
16Mbps, and Other.
Note
The 5Mbps, 6Mbps, 7Mbps, 8Mbps, 9Mbps,
10Mbps, 11Mbps, 12Mbps, 13Mbps, 14Mbps,
15Mbps, and 16Mbps settings are not available
on the PCS-XG77/XG77S.
Audio Mode
Allows you to select the compression format
of audio to be sent to a remote party. When
"Individual Settings for Transmission/
Reception" or "Individual Settings for Point-
to-Point/Multipoint" on the IP page is set to
"On", you can set this item for transmission
and reception, and point-to-point and
multipoint connections individually.
You can select multiple formats from among
G.711, G.722, G.728 and MPEG4 (MPEG4
AAC).
Note
When the remote system does not support the
audio mode selected by the local site, the mode
automatically becomes "G.711".
Far End Camera Control
Allows you to select whether to enable the
control of each other's cameras from each
other's site.
When "Individual Settings for Point-to-
Point/Multipoint" for IP is set to "On", you
can set this item individually for point-to-
point and multipoint connections.
On: Enables the control of each other's
cameras. Normally, set to "On".
Off: Disables the control of each other's
cameras.
H.239
Use of the presentation mode complying
with H.239 allows you to transmit the
presentation data and picture from the
camera simultaneously.
This item allows you to select whether to use
the presentation mode based on the H.239
presentation standard.
On: Enables the presentation mode based on
the H.239 presentation standard.
Off: Disables the presentation mode based
on the H.239 presentation standard.
Registering Local Information
69