Start-Up And Use - Indesit I5TMH6AG Operating Instructions Manual

Start-up and use

Using the hob
GB
Lighting the burners
For each BURNER knob there is a complete ring showing
the strength of the flame for the relevant burner.
To light one of the burners on the hob:
1. Bring a flame or gas lighter close to the burner.
2. Press the BURNER knob and turn it in an anticlockwise
direction so that it is pointing to the maximum flame
setting .
3. Adjust the intensity of the flame to the desired level by
turning the BURNER knob in an anticlockwise direction. This
may be the minimum setting , the maximum setting  or
any position in between the two.
X
flame setting, until the burner is lit.The burner may be
extinguished when the knob is released. If this occurs,
repeat the operation, holding the knob down for a longer
period of time.
! If the flame is accidentally extinguished, switch off the
burner and wait for at least 1 minute before attempting
to relight it.
If the appliance is equipped with a flame failure safety
device*(C), press and hold the BURNER knob for
approximately 2-3 seconds to keep the flame alight and
to activate the device.
To switch the burner off, turn the knob until it reaches
the stop position •.
Practical advice on using the burners
For the burners to work in the most efficient way possible
and to save on the amount of gas consumed, it is
recommended that only pans that have a lid and a flat
base are used. They should also be suited to the size of
the burner:
Burner
Semi Fast (S)
Auxiliary (A)
Triple Crown (TC)
To identify the type of burner, please refer to the diagrams
contained in the "Burner and nozzle specifications".
! For models equipped with a reducer grid, the latter must
be used only for the auxiliary burner, when pans with a
diameter of less than 12 cm are used.
38
If the appliance is fitted with an
electronic lighting device* (X),
press the ignition button, marked

with the symbol , then hold
the BURNER knob down and
turn it in an anticlockwise
C
direction, towards the maximum
Cookware Diameter (cm)
16 - 20
10 - 14
24 - 26
Using the oven
! The first time you use your appliance, heat the empty
oven with its door closed at its maximum temperature
for at least half an hour. Ensure that the room is well
ventilated before switching the oven off and opening the
oven door. The appliance may emit a slightly unpleasant
odour caused by protective substances used during the
manufacturing process burning away.
! Never put objects directly on the bottom of the oven; this
will avoid the enamel coating being damaged.
! Should the appliance be equipped with an electronic
programmer, to use the electric oven, just press buttons
and at the same time (the
on the display) before selecting the desired cooking
function.
! Before operating the product, remove all plastic film
from the sides of the appliance.
1. Select the desired cooking mode by turning the
SELECTOR knob.
2. Select the recommended temperature for the
cooking mode or the desired temperature by turning the
THERMOSTAT knob.
A list detailing cooking modes and suggested cooking
temperatures can be found in the relevant table (see
Oven cooking advice table).
During cooking it is always possible to:
• Change the cooking mode by turning the SELECTOR
knob.
• Change the temperature by turning the THERMOSTAT
knob.
• Stop cooking by turning the SELECTOR knob to the
"0" position.
! Always place cookware on the rack(s) provided.
THERMOSTAT indicator light
When this is illuminated, the oven is generating heat.
It switches off when the inside of the oven reaches the
selected temperature. At this point the light illuminates
and switches off alternately, indicating that the thermostat
is working and is maintaining the temperature at a
constant level.
OPERATION indicator light
When this is illuminated, the oven is generating heat.
Oven light
This is switched on by turning the SELECTOR knob to
any position other than "0". It remains lit as long as the
oven is operating. By selecting
light is switched on without any of the heating elements
being activated.
*
Only available in certain models.
symbol will appear

with the knob, the