Accessories; Labels - Titan 340 Owner's Manual

Item Part # Description
1 704-274 Fluid section, bare (excludes items 23–37) .1
2 704-090 Piston assembly (includes items 9–15) ......1
3 730-508 Retainer ......................................................1
4 700-587 Piston guide ................................................1
5 700-072 Upper packing w/tool ..................................1
6 704-180 Pump block .................................................1
7 227-006 Outlet fitting.................................................1
8 700-601 Lower packing ...........................................2
9 704-089 Piston rod....................................................1
10 762-111 Upper seal ..................................................1
11 762-135 Upper cage .................................................1
12 762-144 Outlet valve ball ..........................................1
13 762-134 Outlet valve seat.........................................1
14 762-057 O-ring..........................................................1
15 762-073 Outlet vavle retainer ...................................1
16 704-289 Bushing.......................................................1
17 700-821 Lower seal ..................................................1
18 730-510 Lower cage .................................................1
19 762-145 Foot valve ball ............................................1
20 762-137 Foot valve seat ...........................................1
21 762-058 O-ring..........................................................1
22 704-054 Foot valve housing .....................................1

Accessories

Airless Tip Selection
Tips are selected by the orifice size and fan width. The proper
selection is determined by the fan width required for a specific
job and by the orifice size that will supply the desired amount
of fluid and accomplish proper atomization.
For light viscosity fluids, smaller orifice tips generally are
desired. For heavier viscosity materials, larger orifice tips are
preferred. Please refer to the chart below.
NOTE: Do not exceed the sprayer's recommended tip
size.
The following chart indicates the most common sizes and the
appropriate materials to be sprayed.
Tip Size Spray Material
.011 – .013 Lacquers and stains
.015 – .019 Oil and latex
.021 – .026 Heavy bodied latex and blockfillers
Fan widths measuring 8" to 12" (20 to 30 cm) are preferred
because they offer more control while spraying and are less
likely to plug.
Liquid Shield Plus
Cleans and protects spray systems
against rust, corrosion and premature
wear. Now with -25º anti-freeze
protection.
Part # Description
314-483 ...........4 ounce bottle
314-482 ...........1 quart bottle
© Titan Tool Inc. All rights reserved.
Quantity Item
23
24 500-200-03 Filter............................................................1
25
26
27
28
29
30
31
32
33
34
35
36
37
38
NOTE: When using "HOT" solvents, replace Viton o-
Piston Lube
Specially formulated to prevent materials
from adhering to the piston rod, which
becomes abrasive to the upper seals.
Piston Lube will break down any material
that may accumulate in the oil cup and
keep it from drying.
Part #
314-481 ...........4 ounce bottle
314-480 ...........8 ounce bottle
Miscellaneous
Part No.
490-012 ...........Hose Coupling, 1/4" x 1/4"
730-397 ...........High Pressure Fl. Gauge
314-171 ...........Lubriplate, 14 ounce individual
Filter Type 314-172 ...........Lubriplate, 6 lb. can
700-1037 ..........Electrostatic discharge (ESD) wrist strap
100 mesh filter
60 mesh filter
30 mesh filter

Labels

Part #
313-2320
313-2418
313-1673
313-1847
23
Part # Description
700-421 Filter housing ..............................................1
560-038 Seal.............................................................1
700-258 PRIME/SPRAY valve assembly
(includes items 27—37)..............................1
700-537 Gasket ........................................................1
221-012 O-Ring, Viton ..............................................1
O-Ring, PTFE.............................................1
222-012
700-246 Valve housing .............................................1
700-721 O-Ring, Viton ..............................................1
O-Ring, PTFE (optional).............................1
700-897
700-250 Valve stem ..................................................1
700-244 Spring .........................................................1
700-248 Valve retainer..............................................1
700-252 Cam base ...................................................1
700-697 Valve handle ...............................................1
700-759 Groove pin ..................................................1
762-202 Packing tool (not shown) ............................1
ring (item 31) with optional PTFE o-ring (700-
897). Install with o-ring tool (700-890).
Description
Description
Description
Front cover label
"340" motor cover label
Warning label
(injection/explosion)
Shock hazard label
Quantity