Table of Contents
Related Manuals for Titan ControlMax 1500
Summary of Contents for Titan ControlMax 1500
- Page 1 OperAting mAnuAl - F - guiDe D’utilisAtiOn - e - mAnuAl Del usO ControlMax ™ Airless, high-pressure sprAying unit AppAreil De pulVÉrisAtiOn À hAute pressiOn sAns Air uniDAD De pulVeriZACiÓn sin Aire y De AltA presiÓn • Form No. 0580356C 0617...
- Page 2 Notes give important information which should be given special attention. When the sprayer is used with a generator or uncontrolled line voltage, the use of Titan’s “Line Surge Protector” (P/N 800-935) is recommended. Attention Make sure to check for grounding continuity after service is performed on any electrical components.
- Page 3 Inspect hose before each use. Replace • Keep area clean and free of paint or solvent containers, any damaged hoses or parts. Only use TITAN original-high- rags, and other flammable materials. pressure hoses in order to ensure functionality, safety and •...
-
Page 4: Table Of Contents
IMPORTANT SAFETY INFORMATION • • Always engage the trigger lock when not spraying. Verify Do not operate the unit when fatigued or under the the trigger lock is functioning properly. influence of drugs or alcohol. • • Verify that all connections are secure before operating the Do not kink or over-bend the hose. -
Page 5: General Information
0.55 150 feet all models: 100 feet Power requirement 15 amp minimum circuit on 115 VAC, 60 Hz current Titan Tool accessory extension cords recommended: generator power 5000 Watt P/N 0090241 20 foot extension cord requirement (disable idle-down feature) P/N 0090242... -
Page 6: Assembly
ASSEMBLY Do not plug in the power cord until assembly is complete. TOOLS NEEDED • Two 6” adjustable wrenches Attach the tool box doors to the top of the sprayer as shown. Snap one peg into one of the orifices, and then snap the other peg into the other orifice. - Page 7 ASSEMBLY (CONTINUED) The spray gun included with the sprayer will have one of two types of hose restraint: 1) the “C” type where the hose is clamped, or 2) the circular type where the hose gets threaded through a hole in the restraint. When attaching the hose to the spray gun, follow the appropriate steps to properly secure the spray hose.
-
Page 8: Parts And Components
PARTS AND COMPONENTS PRIME SPRAY SPRAY PRIME ITEM DESCRIPTION Hose wrap The hose wrap allows for easy storage of the spray hose (cart models only). Tool box The Tool Box provides a place for items such as extra spray tips or wrenches. Pressure control knob / The pressure control knob regulates the amount of force the pump uses to push the fluid and can be ON/OFF switch... -
Page 9: Before You Begin
BEFORE YOU BEGIN This section contains instructions that will be repeated throughout this manual. Read and understand this section before using the equipment. SPRAY GUN TRIGGER LOCk Be careful when handling the spray gun so you do not accidently spray yourself. The high pressure paint stream could pierce your skin causing serious injury. -
Page 10: Load Material
LOAD MATERIAL These steps will prime the system and get it ready to spray. YOU wILL NEED • The material you plan to spray • Extension cord • Waste bucket recommendation: It is good practice to perform the steps on this page using water to familiarize yourself with the function of the unit as well as to ensure the unit is set up properly. -
Page 11: Spraying
SPRAYING Follow these steps to deliver spray material from the material container to the spray gun. YOU wILL NEED • Waste bucket • Scrap material / cardboard • Drop cloths to protect floors and furnishings from overspray Make sure the tip guard is removed. Point the spray gun into a separate waste container. -
Page 12: Practice Spraying
PRACTICE SPRAYING Prior to spraying, it is important that you are using the spray tip / spray material combination that it suitable for your spraying job. Refer to the chart below for a list of recommendations regarding spray tip size, spray material and pressure settings. - Page 13 PRACTICE SPRAYING If the spray pattern becomes distorted or stops spraying completely while the gun is triggered, follow any or all the procedures listed on pages 12-13. If you plan to be away from your spray project for more than one hour, follow the Short Term Storage instructions on page 15.
-
Page 14: Clear The Spray Tip
SPRAYING TROUBLEShOOTING - CLEAR ThE SPRAY TIP If the spray pattern becomes distorted or stops spraying completely while the gun is triggered, the spray tip could be clogged. Follow the steps below. YOU wILL NEED • Scrap material / cardboard Do not attempt to unclog or clean the tip with your finger. -
Page 15: Clean The Inlet Filter
SPRAYING TROUBLEShOOTING - CLEAN ThE INLET FILTER If the spray pattern becomes distorted or stops spraying completely while the gun is triggered, the inlet filter could be clogged. Follow the steps below. YOU wILL NEED • Warm, soapy water for latex material •... -
Page 16: Short Term Storage
ShORT-TERM STORAGE This procedure should be used when taking a short term break or when ending your project for the day. If your break is longer than 16 hours follow cleanup instructions, pages 17-18. YOU wILL NEED • Water • Plastic bag •... -
Page 17: Cleanup
CLEANUP CLEANING NOTES - READ BEFORE CLEANING Follow these steps whenever cleaning with mineral spirits: • When using latex material, clean sprayer and components • If spraying or cleaning with oil-based materials, the spray with warm, soapy water. For oil based material use gun must be grounded while preparing the spray hose mineral spirits. - Page 18 CLEANUP - CONTINUED Point the spray gun at the side of a waste container. Ground the gun against the side of a metal waste container if flushing with mineral spirits. SPRAY While squeezing the trigger, turn the pressure control knob to ‘2’, and turn the PRIME/SPRAY knob to SPRAY.
-
Page 19: Long Term Storage
LONG TERM STORAGE Follow these steps to prepare your sprayer for long- term storage. YOU wILL NEED • Light household oil / Piston Lube • HOUSEHOLD Rags • Two adjustable wrenches The suction tube should still be removed from the end of the previous section and the PRIME/SPRAY knob should be in the PRIME position. -
Page 20: Cleaning The Inlet Valve
CLEANING ThE INLET vALvE Cleaning or replacing the inlet valve may be required if the unit has priming problems. Priming problems may be prevented by properly cleaning the sprayer and following the long-term storage steps. YOU wILL NEED • Adjustable wrench or 10 mm allen wrench •... -
Page 21: Cleaning The Outlet Valve
CLEANING ThE OUTLET vALvE Cleaning or replacing the outlet valve may be necessary if spray performance remains poor after following the steps in the Troubleshooting section. Call Technical Service (1-866-848-2698) to order a new outlet valve assembly. YOU wILL NEED •... -
Page 22: Troubleshooting
TROUBLEShOOTING PROBLEM CAUSE SOLUTION A. The sprayer does not turn on. 1. The sprayer is not plugged in. 1. Plug the sprayer in. 2. Pressure control knob is set to OFF. 2. Turn pressure control knob to recommended setting. 3. The sprayer shuts off while under pressure. 3. -
Page 23: Warranty
This warranty does not cover damage resulting from improper use, accidents, user’s negligence or normal wear. This warranty does not cover any defects or damages caused by service or repair performed by anyone other than a Titan Authorized Service Center. -
Page 24: Parts List
Parts List • Liste de Pièces • Lista de Piezas Main asseMbLy (stand ModeLs) • enseMbLe PrinciPaL (ModèLes de suPPort) • Montaje PrinciPaL (ModeLos de soPorte) 1500 1700 1500 1700 Description Description Descripción 0580389 --------- Base assembly Ensemble de la base Conjunto de la base --------- 0580163... - Page 25 Parts List • Liste de Pièces • Lista de Piezas Main asseMbLy (cart ModeLs) • enseMbLe PrinciPaL (ModèLes de chariot) • Montaje PrinciPaL (ModeLos de carro) 1700 Pro / 1900 Pro replacement parts available by calling customer service On peut obtenir des pièces de rechange en appelant le Service à...
- Page 26 Parts List • Liste de Pièces • Lista de Piezas sPray gun asseMbLy • PistoLet de PuLvérisation • PistoLa de rociadora 1700 Pro 1500 1700 1900 Pro Description Description Descripción 353-700 ------- ------- Spray gun assembly, Ensemble du pistolet de Conjunto de la pistola ControlMax (includes pulvérisation, ControlMax...
- Page 27 Parts List • Liste de Pièces • Lista de Piezas suction set asseMbLy • enseMbLe d’asPiration • conjunto de succiÓn 1700 Pro 1500 1700 1900 Pro Description Description Descripción ------- ------- ------- Suction tube Tube d’aspiration Tubo de succión 0580487 0580487 0580208 Return tube...
- Page 28 accessories• accessoires • accesorios PART NO. DESCRIPTION DESCRIPTION DESCRIPCIóN SPRAY GUNS PISTOLETS DE PULvéRISATION PISTOLAS DE PULvERIzACIóN 353-700 ControlMax spray gun Pistolet de pulvérisation ControlMax Pistola de pulverización de ControlMax 353-701 ControlMax Pro spray gun Pistolet de pulvérisation ControlMax Pro Pistola de pulverización de ControlMax Pro SPRAY TIPS AND ACCESSORIES EMBOUTS DE PULvéRISATION ET ACCESSOIRES...