Table of Contents
Advertisement
18 EVEP611SB, EVEP614BB
OPERATING SEQUENCE
Select the oven function
•
Turn the oven function selector clockwise to select the
desired oven function.
Note: each oven function has a default temperature
which can then be adjusted as outlined below.
Selecting the oven temperature
–
•
Toggle the temperature selector (left
or right
required to set the desired cooking temperature in °C.
Note: the temperature can be adjusted at any time
throughout the cooking time.
IMPORTANT!
Pre-heating
For best cooking results , pre-heat the oven. Pre-heating
allows the oven to reach the required temperature
quickly and efficiently as well as cook food at the correct
temperature for the entire cook time.
1. With 'Rapid Heat' function
This function allows the oven to reach preset
temperature quicker than any other cooking function.
Turn the function selector to 'Rapid Heat', then set the
desired temperature, by rotating the oven temperature
selector. When the heating light goes out, the oven
has reached the desired temperature. Select the oven
function required and place the food in the oven.
2. With other oven functions
Set the desired temperature by rotating the oven
temperature selector. When the indicator light
goes out the oven has reached the desired preset
+
) as
temperature, place the food in the oven, close the
door and set the timer if you desire.
3. With 'Grill' function
Pre-heat the grill for at least 3 minutes to obtain best
results. This will help to seal the natural juices of steak,
chops and other meats for a better flavour.
IMPORTANT!
Cooling / Vent fan
The appliance is fitted with a cooling fan. This prevents
the kitchen cabinet from overheating and reduces the
condensation inside the oven. It will operate whenever
the oven is in use and blow warm air across the top of the
oven door.
Note: If the oven is still hot from cooking, the cooling fan
will keep running to cool the oven down and will switch
off by itself once cool.
Condensation
Excess condensation may fog the oven door. This may
happen when cooking large quantities of food from a
cold start. Minimise condensation by:
– Keeping the amount of water used whilst cooking to
a minimum.
– Making sure the oven door is firmly closed.
– Baking custard in a baking dish that is slightly
smaller than the water container.
– Cooking casseroles with the lid on.
Note: If using water in cooking, this will turn to steam
and may condense outside the appliance. This is not
a problem or fault with the oven.
USING THE APPLIANCE
Cooking with the timer
1
2
13
12
11
10
9
8
7
6
1
On when the timer is set
2
On when oven warming up
3
3 bars displayed when oven reaches set
temperature
4
On when oven cooling down
5
Oven door locked
6
Press to display current oven temperature
7
Press to increase hours/minutes
8
Press to start timer mode.
Hold to turn oven light on/off
9
Press to decrease hours/minutes
10
Press to toggle through the timer modes
11
End time icon
12
Cook time icon
Time of day icon
13
Adjusting the clock
To change the time, press and hold the 'TIME' button
until the clock symbol begins to flash. The hour
display will be ready to change.
+
–
•
Press
or
, then press 'TIME' when you have the
right hour.
•
The minutes will flash and can be set in the same
manner.
•
5 seconds after the last change, the clock display will
stop flashing, confirming that the time has been set.
Note: The clock has a 24 hour display.
The timer can be used to turn the oven off in two ways by
setting the cooking time (duration) or by setting the end
time (time of day you want the oven off).
EVEP611SB, EVEP614BB 19
Setting the cook time
1.
Use the knobs to select the desired oven function and
cooking temperature.
2. Press the 'TIME' button as often as necessary, until
the 'cook time'
symbol appears.
3. Set the desired cooking time commencing with
3
+
–
minutes by using the
or
buttons, whilst the
symbol is flashing, then press the 'TIME' button
4
again and set the hours by using the
2 5
After 5 seconds from the last time adjustment the
symbol will stop flashing. The appliance is now
programmed and the display will countdown to zero.
4. When the set time has elapsed, a signal will sound
and the appliance will turn off. To stop the signal,
press any button on the clock and then turn the oven
function selector to OFF.
Note: Cooking time cannot be set for the Rapid Heat
function. The feature can be cancelled at any time by
returning the function selector to off.
Setting the end time
1.
Use the knobs to select the desired oven function and
cooking temperature.
2. Press the 'TIME' button as often as necessary, until
the 'end time'
symbol appears.
3. Set the desired end time commencing with hours using
+
–
the
or
buttons whilst the
symbol is flashing,
then press the 'TIME' button again and set the minutes
+
–
by using the
or
buttons. After 5 seconds from the
last time adjustment the
symbol will stop flashing
and the appliance is now programmed.
4. When the set time has elapsed, a signal will sound
and the appliance will turn off. To stop the signal,
press any button on the clock and then turn the oven
function selector to OFF.
Note: Stop time cannot be set for the Rapid Heat function.
Setting the delayed start cooking time
The 'cook time' and 'end time' functions can be
combined to switch the oven on and off at a specific
time during the day.
1.
Select the desired oven function and cooking
temperature.
2. Press the 'TIME' button as often as necessary, until
the 'cook time'
symbol appears.
3. Set the desired cooking time by using
whilst the
symbol is flashing.
4. Press the 'TIME' button as often as necessary, until
the 'end time'
symbol appears flashing.
5. Set the desired switch-off time using the
the 'end time'
symbol is flashing.
6. 5 seconds after the last change the 'cook time' and
'end time' arrows are lit to confirm that the oven has
been programmed.
7. When the delayed start cooking time has elapsed,
a signal will sound and the appliance will turn off. To
stop the signal, press any button on the clock and
then turn the oven function selector to OFF.
Note: Delayed start cooking time cannot be set for the
Rapid Heat function. The feature can be cancelled at
any time by returning the function selector to off.
+
–
or
buttons.
+
–
or
buttons,
+
–
or
whilst
Hide quick links:
Advertisement
Table of Contents
