Towing Hitch; Tyre Pressure; Steering Wheel - Castelgarden XM130 Instructions For Use Installation And Servicing

EN
The machine may not be operated un-
less the engine casing is folded down.
Risk of burns and crushing injuries.
2.3 Battery
See "6.8 Battery".
2.4 Seat
Release the catch (2:S) and fold up the seat brack-
et.
Install the mounting in the rear (upper) holes as
follows:
1. Install the shoulder washers (2:F) on the screws
(2:G).
2. Insert the screws through the slots in the brack-
et. Place a washer (2:E) between the seat and
the bracket.
3. Tighten the screws in the seat. Tightening
torque: 9±1.7 Nm.
If the screws are tightened more than
9±1.7 Nm, the seat will be damaged.
4. Check that the seat moves easily in the slots in
the bracket.
Install the mounting in the front (lower) holes as
follows:
1. Install a washer (2:E) on each screw (2:G).
2. Insert the screws through the slots in the bracket
and tighten by hand in the seat.
3. Fold the seat down and place it in the desired
position.
4. Tighten the screws in the seat. Tightening
torque: 9±1.7 Nm.
If the screws are tightened more than
9±1.7 Nm, the seat will be damaged.
The seat can be folded. If the machine is parked
outside when it is raining, fold the seat forward to
protect the seat cushion from getting wet.
The seat is locked. To fold the seat up or down, re-
lease the catch (2:S).

2.5 Steering wheel

In order to minimise the axial play in the steering
column, the shim washers (4:K) and/or (4:L) must
be installed on the steering column between the
steering column jacket and the bracket as follows.
1. Install the steering column jacket on the steer-
ing column and secure by knocking in the cotter
pin (4:J) approximately 1/3 of its length.
2. Pull the steering column jacket and the steering
column up.
42
ENGLISH
3. From the outside, check whether no washers,
the 0.5 mm washer, the 1.0 mm washer or both
washers can be inserted into the gap. The wash-
er/washers must not be forced in, as there must
be a little axial play.
4. Pull out the cotter pin and dismantle the steering
wheel jacket.
5. Install the washer/washers in accordance with
point 3 above.
6. Install the steering column jacket on the steer-
ing column and secure by knocking in the cotter
pin fully. Use a counterhold.

2.6 TOWING HITCH

Screw the towing hitch (5:A) into the two holes on
the underside of the rear axle using screws 5:B).
Tighten the screws properly.
Tightening torque: 22 Nm.
2.7 Deck mount
This only describes installation on the right-hand
axle. The same procedure must be carried out on
the left-hand axle.
1. Remove the circlip (17:M) and the outer washer
(17:N).
2. Install the deck mount (17:O).
The washer (17:N) with an inner lug
must always be placed against the cir-
clip. Otherwise there is a risk of the cir-
clip coming loose.
3. Install the outer washer (17:N) and the circlip
(17:M).
4. Lubricate the deck mount's lubricating cup us-
ing a grease gun until grease penetrates along
side the axle.
The screws (1:P) and the nuts (1:Q) must be used
to install the work tool in the deck arms (17:O).

2.8 TYRE PRESSURE

Check the air pressure in the tyres. Correct air
pressure:
Front: 0.4 bar (6 psi)
Rear: 1.2 bar (17 psi)
2.9 ACCESSORIES
For the installation of accessories, see separate in-
stallation guide supplied with each accessory.
Note: The cutting deck is regarded as an accessory
here.