Setting The Cleaning Level; After Cleaning; Care And Cleaning; Cleaning Agents - Siemens HB36LB.60 Instruction Manual

Setting the cleaning level

Press the button.
s
1.
Cleaning level 3 is suggested.
If you wish to change the cleaning level:
Select the desired cleaning level using the rotary selector.
2.
Start the cleaning operation with
3.
Once cleaning has finished
: appears in the display. The oven stops heating.
‹ ‹‹
Cancelling cleaning
Press and hold the † button until
appears. You can make new settings.

Care and cleaning

With good care and cleaning, your oven will remain clean and
fully-functioning for a long time to come. Here we will explain
how to maintain and clean your oven correctly.
Notes
Slight differences in the colours on the front of the oven are
■
caused by the use of different materials, such as glass,
plastic and metal.
Shadows on the door panel which look like streaks, are
■
caused by reflections made by the oven light.
Enamel is baked on at very high temperatures. This can
■
cause some slight colour variations. This is normal and does
not affect their function. The edges of thin trays cannot be
completely enamelled. As a result, these edges can be
rough. This will not impair the anti-corrosion protection.

Cleaning agents

To ensure that the different surfaces are not damaged by using
the wrong cleaning agent, observe the information in the table.
Do not use
sharp or abrasive cleaning agents,
■
cleaning agents with a high concentration of alcohol,
■
hard scouring pads or sponges,
■
high-pressure cleaners or steam cleaners.
■
Wash new sponge cloths thoroughly before use.
Area Cleaning agents
Oven front Hot soapy water:
Clean with a dish cloth and dry with a
soft cloth. Do not use glass cleaners or
glass scrapers.
Stainless steel Hot soapy water:
Clean with a dish cloth and dry with a
soft cloth. Remove flecks of limescale,
grease, starch and albumin (e.g. egg
white) immediately. Corrosion can form
under such residues.
Special stainless steel cleaning prod-
ucts suitable for warm surfaces are avail-
able from our after-sales service or from
specialist retailers. Apply a thin layer of
the cleaning product with a soft cloth.
Door panels Glass cleaner:
Clean with a soft cloth. Do not use a
glass scraper.
Glass cover for the Hot soapy water:
oven light Clean with a dish cloth.
Seal Hot soapy water:
Do not remove. Clean with a dish cloth. Do not scour.
† .
: 3D hot air, 160 °C
Adjusting the cleaning level
Once cleaning starts, the cleaning level can no longer be
changed.
Setting cleaning to run overnight
So that you can use your oven throughout the day, delay the
end of the cleaning process to during the night. See the Time-
setting options section, setting a later end time.

After cleaning

When the cooking compartment has cooled down completely,
wipe the salt residues off the self-cleaning surfaces with a
damp cloth.
Area Cleaning agents
Shelves Hot soapy water:
Soak and clean with a dish cloth or
brush.
Telescopic shelves Hot soapy water:
Clean with a dish cloth or a brush. Do
not soak or clean in the dishwasher.
Accessories Hot soapy water:
Soak and clean with a dish cloth or
brush.
Cleaning the self-cleaning surfaces in the cooking
compartment
The back wall in the cooking compartment is coated with a
highly porous ceramic layer. This coating absorbs and
disintegrates splashes from baking and roasting while the oven
is in operation. The higher the temperature and the longer the
oven is in operation, the better the result will be.
If splashes are still visible even after repeated use, proceed as
follows:
Clean the floor, ceiling and side panels of the cooking
1.
compartment thoroughly.
Set : 3D hot air.
2.
With the door closed, heat up the empty oven for
3.
approximately 2 hours at maximum temperature.
The ceramic coating is regenerated. When the cooking
compartment has cooled down, remove the brown or white
residue with water and a soft sponge.
Light discolouration of the coating does not affect automatic
self-cleaning.
If you buy the "self-cleaning ceiling and side panels" optional
accessory at a later stage, you can regenerate the self-cleaning
surfaces with the cleaning system. For this, please see the
Cleaning system section.
Caution!
Never use abrasive cleaning agents. You will scratch or
■
destroy the highly porous coating.
Never treat the ceramic coating with oven cleaner. If oven
■
cleaner accidentally gets onto it, remove it immediately with a
sponge and plenty of water.
Cleaning the cooking compartment floor, ceiling and side
walls
Use a dish cloth and hot soapy water or a vinegar solution.
If there are heavy deposits of dirt, use a stainless steel scouring
pad or oven cleaner. Only use when the cooking compartment
is cold. Never treat the self-cleaning surfaces with a scouring
pad or oven cleaner.
15