2 Mega Pixel Water-Proof IR Network Camera User Manual Please read this instruction carefully for correct use of the product...
Page 2
Before use this product Before operation, we strongly advise users to read this manual and keep it properly for using later. This is product instructions not quality warranty. We may reserve the rights of amending the typographical errors, inconsistencies with the latest version, software upgrades and product improvements, interpretation and modification.
Page 1 IP CAMERA USER MUANUAL 1 Introduction 1.1 Summarization This IP-CAMERA (short for IP-CAM) is designed for high performance CCTV solutions. It adopts state of the art video processing chips. It utilizes most advanced technologies, such as video encoding and decoding technology, complies with the TCP/IP protocol, SoC, etc to ensure this system more stable and reliable.
Page 6
Page 2 IP CAMERA USER MUANUAL F o c u s Z o o m Step 1: Remove the sun shade and lens case from the device as shown above. Step 2: Loosen the screws of the lens for focusing. Then rotate the lens left or right to adjust the focus.
Page 3 IP CAMERA USER MUANUAL 2 Installation 2.1 Install IP-CAM to Ethernet Network The connection of digital video server is show below. Figure 2-1 Connection Please connect the PC and IP-CAMERA in accordance with the above picture. The connection steps are shown as below: Step 1: Connect the monitor, microphone and network to the device.
Page 8
Page 4 IP CAMERA USER MUANUAL Item Specification Intel Pentium 3.0 GHz or AMD 3000+ Memory 160GB Recommended PC Specification -9 channels: Item Specification Intel Core 2 Duo 1.8 GHz or AMD Dual core 3800+ Memory 250GB Recommended PC Specification -16 channels: Item Specification Intel Core 2 Duo 2.2 GHz or AMD Dual core 3800+...
Page 5 IP CAMERA USER MUANUAL 3 IE Remote Access IP-Cam can be connected through LAN or WAN. Here only take IE browser (6.0) for example. The details are as follows: 3.1 LAN In LAN, there are two ways to access IP-Cam: 1. Access through IP-Tool; 2. Directly access through IE browser.
Page 10
Page 6 IP CAMERA USER MUANUAL For example, the network segment of this computer is 192.168.13.x under the local config table. So, please modify the IP address, Gateway of IP-Cam which must be in the same network segment with the computer. Modifying the network, you have to input the password and click “OK”...
Page 7 IP CAMERA USER MUANUAL 3.1.2 Directly Access through IE The default network settings are as shown below: IP address: 192.168.226.201 Subnet Mask: 255.255.255.0 Gateway: 192.168.226.1 HTTP: 80 Data port: 9008 The first time you used the IP-CAM, you should connect the device with the above default settings.
Page 8 IP CAMERA USER MUANUAL download Active X control, please refer to Q4 of chapter 9. Step 3: After downloading Active X control, the login dialog box will pop up. Step 4: Input user name and password in the login dialog box and click “OK” button to enter into the live interface.
Page 9 IP CAMERA USER MUANUAL 4 Remote Preview 4.1 The Remote Preview Interface Fig 4-1 Remote Preview People icon Fix size Zoom in Zoom in Zoom out Full screen Start record Playback Snap Enable audio When motion detection alarm is triggered, the people icon turns red. ...
Page 10 IP CAMERA USER MUANUAL Fig 4-2 record playback interface After selecting the record date, the record files will be displayed in the record file list box. User can double click a certain record file to playback or check a certain file. Then click Play button to do playback.
Page 15
Page 11 IP CAMERA USER MUANUAL scroll bar to view all snapped pictures. Fig 4-4 Single Snap Fig 4-5 Multi-picture Snap...
Page 12 IP CAMERA USER MUANUAL 5 Remote Live Surveillance Functions of remote configurations include: System Configuration, Video Configuration, Alarm Configuration, Network Configuration and Advanced Configuration. User should firstly select the menu on the left, and then setup the relative parameters. When a user setup parameters of a certain device, other users can not setup this device.
Page 13 IP CAMERA USER MUANUAL 5.1.2 Date & Time Configuration Setting steps: 1. Enter into "System Configuration" “Date & Time”. Refer to Fig 5-2: 2. Select “Modify Time " to self-define time. Choose "Time Zone" according to user‟s location. 3.
Page 14 IP CAMERA USER MUANUAL 2. User can adjust Brightness, Contrast, Hue and saturation of the picture. 3. Select white balance mode. 4. Sharpen, denoise , white balance, frequency, CVBS format and Day-Night mode are adjustable. 5. User also can enable the image mirror and image overturn function. 6.
Page 15 IP CAMERA USER MUANUAL 5.2.4 Video Mask You can set 4 mask area at most. Fig 5-6 Video Mask Enable the mask, select color and transparent of the mask area and then drag the mouse to set the mask area. This will take you see a gridding area. After that, click “Save” button to save the settings.
Page 16 IP CAMERA USER MUANUAL Fig 5-7 Motion Detection Area 5.3.2 Motion Detection Trigger 1. Enter into “Alarm Configuration" "Motion Detection Trigger" to display a interface as shown in Fig 5-8: 2. Check "Enable alarm" check box. Then all functions under this interface will be activated.
Page 17 IP CAMERA USER MUANUAL 5.3.3 Motion Detection Schedule Enter into “Alarm configuration" "Motion Detection schedule" interface as shown in Fig 5-9: Week schedule User could set the alarm time from Monday to Sunday for alarm everyday in one week. Note: The lengthwise means one day of a week;...
Page 18 IP CAMERA USER MUANUAL Fig 5-10 Port Config 2. Input port number for IE access in the "HTTP Port" textbox. 3. Input the port number for audio & video transmission in the "Data Port" textbox. 5.4.2 Wired Enter into "Network Configuration"...
Page 19 IP CAMERA USER MUANUAL Fig 5-12 Transit 2. Check “transit enable”. Then save the setting. 3. Input www.upnpicp.com in IE address; download and install Active X. Then a window shows up as Fig 5-13: Fig 5-13 Login 4. Input the only device ID of the IP-CAM or user-defined name. And then input user name and password.
Page 20 IP CAMERA USER MUANUAL 1. Check “Do you want IP Camera to connect Server. 2. Check the IP address and port of the transfer media server in the ECMS/NVMS. Then enable the auto report in the ECMS/NVMS when adding a new device. Then input the remaining information of the device in the ECMS/NVMS.
Page 25
Page 21 IP CAMERA USER MUANUAL Parameter Meaning Address of the website which provided by domain name supplier. The optional: www.dns2p.net , www.88ip.net ,www.meibu.com , DDNS server www.dyndns.com,www.no-ip.com,www.3322.org and mintdns type. User name Log in the website of domain name supplier Log in the website of domain name supplier Password 1.
Page 22 IP CAMERA USER MUANUAL Step 1: Click "Domain Management" on the left to set the domain. Domain setup Step 2: Input the domain in the textbox. For example, you set „IP-CAMERA‟ as the domain. Step 3: Click "Submit" button, the system will pop up a dialog box to show that the domain is added successfully.
Page 23 IP CAMERA USER MUANUAL Fig 5-17 RTSP 1. Select “Enable RTSP server. 2. RTSP Port: Access Port of the streaming media. The default number is 554. 3.RTSP Address: The RTSP address you need to input in the media player. 4.
Page 24 IP CAMERA USER MUANUAL If “Show icons for networked UPnP devices” can‟t display in the “Network Tasks” list box, please follow the below operation: Click “Tools”-- “Folder options” Check the “Show common tasks in folders” in the “Tasks” check box, UPnP icon will display.
Page 25 IP CAMERA USER MUANUAL Fig 5-20 FTP Setting 1. Add: Click Add button to input FTP server‟s server name, address, port number, user name, password, and upload path, click OK to confirm the setting. Refer to Fig 5-21: 2.
Page 30
Page 26 IP CAMERA USER MUANUAL Fig 5-22 User Configuration Fig 5-23 Add User Note: After bind physical address to the IP-CAM, user can access the device on this PC in network only. If the MAC address was ““00:00:00:00:00:00” which means it can be connected to any computers.
Page 27 IP CAMERA USER MUANUAL Note: The default super administrator cannot be deleted. Parameter Meaning User Name User name to operate the logon client end User Type Type of users, normal user, advanced user and super administrator The MAC addresses of user access the server which should setup Binding MAC address according to actual MAC address of server.
Page 28 IP CAMERA USER MUANUAL Fig 5-26 Security Configuration 5.5.4 Configure Backup & Restore Enter into Advanced configurationConfigure Backup & Restore Interface. to Fig 5-27. Import & Export Configuration: User can import or export the setting information from PC or to device. 1.
Page 29 IP CAMERA USER MUANUAL Fig 5-28 Reboot device interface 5.5.6 Upgrade Enter into Advanced Configuration—Upgrade interface shown as Fig 5-29: 1. Click “Browse” button to select the save path of the upgrade file 2. Click “Upgrade server firmware” button to start upgrading the application program 3.
Page 30 IP CAMERA USER MUANUAL 6 Mobile Surveillance This IP-CAM supports mobile surveillance by phones with Windows mobile, iPhone, Android and Blackberry OS. Please check the operation system version of mobile before use; and connect the IP-CAM to Internet. 6.1 Network Configuration ...
Page 35
Page 31 IP CAMERA USER MUANUAL Step 3: Click “Install App” button as shown in the figure on the left. Step 4: Input iTunes Store password and then click “OK”. The software will be installed automatically. Install Software through PC Step 1: Install iTunes store in PC and then login.
Page 36
Page 32 IP CAMERA USER MUANUAL Step 3: Search “SuperLivePro” and select it. Step 4: Click “Download” button. Step 5: Input username and password.
Page 37
Page 33 IP CAMERA USER MUANUAL Step 6: Synchronously apply SuperLivePro software to iPhone/iPad. SuperLivePro Instruction Login Step 1: Choose network type. There are two network connection ways:...
Page 38
Page 34 IP CAMERA USER MUANUAL 3G/3G +WIFI, well video quality. This network supports main stream and sub stream. The real-time image will be displayed by using sub stream. 3G-, poor video quality contrast to the above mentioned network. Step 2: Input server, account and password. Server: WAN IP address (or domain name) plus HTTP port of the device.
Page 39
Page 35 IP CAMERA USER MUANUAL :Help button. Help you know about the use of this software quickly. :CMS button. Make you preview the live image of multi-devices. :Log off button. Click this button to return to the login interface. :Screen mode button.
Page 40
Page 36 IP CAMERA USER MUANUAL Delete device: Click button behind the device name to delete this device. Edit device: Click button behind the device name to edit the information of this device. Backup & restore: It is recommended to click【Backup】button to reserve the information of all devices.
Page 41
Page 37 IP CAMERA USER MUANUAL Fig 1 Fig 2 Fig 3 Fig 4 Fig 5 CMS Function This function makes multi-device managements and preview come true. Step 1: Click to enable CMS function. When this icon turns green, it means this function is enabled.
Page 42
Page 38 IP CAMERA USER MUANUAL If channels have been added into the group, you can see the images by clicking the group name. On viewing the group channel images, click button and select channels to check other channel images. Click 【...
Page 43
Page 39 IP CAMERA USER MUANUAL Playback Interface Click “Playback” button to enter the playback interface. Then click “Search” button to search the file. To play the record by click this file name. Image View Click button to view the captured pictures.
Page 40 IP CAMERA USER MUANUAL Settings Interface In this interface, you can configure the local settings. 10. Information Interface In this interface, you can view system information. 6.3 By Phones with Android OS Software Installation Step 1: Run “Play Store” (or Google market) program. Step 2: Search “SuperLivePro”.
Page 45
Page 41 IP CAMERA USER MUANUAL Step 3: Press “Install” button. Step 4: Install the software subject to the notes. Once the downloading is done, the software will install automatically. Login Step 1: Configure the network of your device and mobile phone.
Page 46
Page 42 IP CAMERA USER MUANUAL Step 2: Input the WAN IP address/domain name and port of your device in the sever column. The port should be HTTP port of your device. The default http port of the device is 80. If you have changed your http port, please enter the new port here. For example: 210.21.228.183:89 or 123.dvrdydns.com:89.
Page 47
Page 43 IP CAMERA USER MUANUAL The first picture The previous picture Next picture The last picture Zoom in Zoom out Delete Record Playback Click “Playback” in the main menu interface to enter playback interface. Then choose the channel you want to playback. This will take you to see the record file. Click this file to play.
Page 48
Page 44 IP CAMERA USER MUANUAL In the main menu interface, click “Server list” to see the above picture on the left hand. Add Server: Click button to pop up a window as shown in the above picture on the right hand.
Page 49
Page 45 IP CAMERA USER MUANUAL Storage: Setup the relevant parameters of mobile video. Information View...
Page 46 IP CAMERA USER MUANUAL 7 Use method for IP-TOOL Updating through IP-Tool Note: Do not cut off power supply and internet when updating; If the device is unable to start because of the failure of upgrade, it needs to retrofit. First,...
Page 51
Page 47 IP CAMERA USER MUANUAL Modify IP address and click OK button to exit the dialog box, IP-Tool will display the new IP address. Upgrading Software Select the device and right click to choose “Update software” menu. Input the username and password.
Page 52
Page 48 IP CAMERA USER MUANUAL Enter into Kernel upgrade dialog box, input user name and password, click “Browse” to select the Update file (mboot8180-8180) and click “Update” button to start updating. When upgrading, please do not disconnect PC to device and make sure the power is on. The update progress bar will display as below: After finishing upgrading, a message box will pop up.
Page 53
Page 49 IP CAMERA USER MUANUAL 8 Q & A Q: How to find my password if I forget it? A:Joint the default line and GND line to reset. Default IP: 192.168.226.201 User name: admin Password: 123456 Q:Fail to connect devices through IE browser, why? A: Network doesn‟t connect well.
Page 54
Page 50 IP CAMERA USER MUANUAL Fig 4-1 Fig 4-2 ④ then click ok to finish setup. b. Other plug-ins or anti-virus blocks ActiveX. Please uninstall or close them. Q:No sound can be heard, why? A:Without connect audio input device. Please connect and try again. B: Without enable audio function at the corresponding channel.
Page 51 IP CAMERA USER MUANUAL 9 Specification Model 1.3Mega Pixel Water-Proof IR Camera Video Compression H.264 Audio Compression G711A Image Resolution 720P, VGA, QVGA Shutter 1/25s~1/100000s Low illumination 0 Lux (LED ON) Lens 4mm, (options: 6mm/8mm) 3.3-12 mm (varifocal lens) White Balance Supports many modes, such as, auto, manual, indoor, outdoor Display Resolution...
Page 56
3. IE Network Connection User can connect IP-CAM through LAN or WAN. Here only take IE browser(6.0) for example. The details are as follows: 3.1 LAN In LAN, there are two ways to access IP-CAM: 1. access through IP-Tool; 2. directly access through IE browser.
Page 57
Step1: Here we take 192.168.13.51 for example as shown below . Please modify the IP Connecting according to above steps in LAN; Enter into the System Congfig→Network Config address of your device according to practical situation. After finishing, please input →Port to set up the port number.