Hangar 9 40-Size Floats Assembly Manual
  1. Manuals
  2. Brands
  3. Hangar 9 Manuals
  4. Toy
  5. 40-Size Floats
  6. Assembly manual

Hangar 9 40-Size Floats Assembly Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
40-Size Floats
Assembly mAnuAl

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 40-Size Floats and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Hangar 9 40-Size Floats

Summary of Contents for Hangar 9 40-Size Floats

  • Page 1 40-Size Floats Assembly mAnuAl...

  • Page 2: Table Of Contents

    Table of Contents Instructions for Disposal of WEEE by Users in the European Union . . . . . . . . . . . . . . . . . . . . . . . . . . . . Contents of Kit .

  • Page 3: Contents Of Kit

    Contents of Kit HAN4016 Hardware Set HAN4017 Steel Strut Set HAN4018 Pushrod & Tube, Nylon Horn, EZ Connector HAN4019 Float w/o Servo Mount HAN400 Float w/Servo Mount Required Tools and Adhesives Tools • Drill • Hobby knife • Covering iron •...

  • Page 4: Warranty Period

    Warranty Period Exclusive Warranty- Horizon Hobby, Inc ., (Horizon) warranties that the Products purchased (the "Product") will be free from defects in materials and workmanship at the date of purchase by the Purchaser . Limited Warranty (a) This warranty is limited to the original Purchaser ("Purchaser") and is not transferable . REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER .

  • Page 5: Questions, Assistance, And Repairs

    Questions, Assistance, and Repairs Your local hobby store and/or place of purchase cannot provide warranty support or repair . Once assembly, setup or use of the Product has been started, you must contact Horizon directly . This will enable Horizon to better answer your questions and service you in the event that you may need any assistance .

  • Page 6: Safety, Precautions, And Warnings

    Before Starting Assembly Before beginning the assembly of the 40-size floats, remove each part from its bag for inspection . Closely inspect the contents for damage . If you find any damaged or missing parts, contact the place of purchase .

  • Page 7: Fuselage Preparation

    Fuselage Preparation Required Parts  Step 2 • Assembled fuselage • Main Strut Test fit the rear strut support inside the fuselage . The • Rear strut support • Gear strap () curved plywood will fit tight against the bottom of the fuselage .
  • Page 8 Fuselage Preparation   Step 4 Step 6 Once the epoxy has fully cured, use a covering iron and Install one end of a Y-harness into the Ernst charge the supplied covering to cover over the rear strut support . receptacle .

  • Page 9: Float Installation

    Float Installation Required Parts  Step 2 • Assembled fuselage • Float (right and left) Install the rudder servo into the right float using the • Strut mount (4) • Rudder hardware provided with the servo . • Pushrod wire •...
  • Page 10 Float Installation   Step 5 Step 7 Install the pushrod connector to the center hole of the Use the radio to move the rudder servo fully to the right . steering arm using the connector backplate . Make sure the With the steering arm almost touching the float, secure the hole for the screw in the arm is facing toward you and the brass pushrod connector and pushrod wire using a 3mm x...
  • Page 11 Important: If installing on a model other  Step 9 than the Hangar 9 J-3 Cub, the floats Attach the floats to the strut using four 5/3-inch wheel should be installed such that the step collars and a 1 .5mm hex wrench .
  • Page 12 Float Flying Flying from floats can be great fun . There are a few things Once in the air, you will find the plane to behave slightly to remember when you hit the lake . First, make sure you different than before . The added weight below the model pick a location where you can take off and land parallel to acts similar to a pendulum effect in flight .
  • Page 13 Notes...

  • Page 14: 007 Official Ama National Model Aircraft Safety Code

    2007 Official AMA National Model Aircraft Safety Code GENERAL 7) I will not operate models with pyrotechnics (any device that explodes, burns, or propels a projectile 1) I will not fly my model aircraft in sanctioned of any kind) including, but not limited to, rockets, events, air shows or model flying demonstrations until explosive bombs dropped from models, smoke it has been proven to be airworthy by having been...

  • Page 15: 007 Official Ama National Model Aircraft Safety Code

    2007 Official AMA National Model Aircraft Safety Code 5) Flying sites separated by three miles or more Organized RC Racing Event are considered safe from site-to site interference, 10) An RC racing event, whether or not an AMA Rule even when both sites use the same frequencies . Any Book event, is one in which model aircraft compete circumstances under three miles separation require in flight over a prescribed course with the objective of...
  • Page 16 © 007 Horizon Hobby, Inc . 4105 Fieldstone Road Champaign, Illinois 618 (877) 504-033 horizonhobby.com 10490...

Table of Contents