Hangar 9 Tribute 4D 36 Plug-N-Play Assembly Manual

Advertisement

Quick Links

Specifications
Wingspan: ............................... 44
Fuselage length: ........................... 48" (1219.2mm)
Wing area: ........................ 690 sq. in. (44.5 sq dm)
Tribute 4D 36
Plug-N-Play
ASSEMBLY MANUAL
5
/
" (1133.4mm)
8
��
Weight: ................................ 4–4.5 Lbs (1.8–2 kg)
Engine: .................... Evolution™ .36 NT (Included)
Radio: ................................. 4 channel w/ 5 servos

Advertisement

Table of Contents
loading

Summary of Contents for Hangar 9 Tribute 4D 36 Plug-N-Play

  • Page 1 � �� Tribute 4D 36 Plug-N-Play ™ ASSEMBLY MANUAL Specifications Wingspan: ....... 44 " (1133.4mm) Weight: ........ 4–4.5 Lbs (1.8–2 kg) Fuselage length: ......48" (1219.2mm) Engine: ....Evolution™ .36 NT (Included) Wing area: ......690 sq. in. (44.5 sq dm) Radio: .........
  • Page 2: Table Of Contents

    Table of Contents Replacement Parts Layout............3 Additional Required Equipment.
  • Page 3: Replacement Parts Layout

    Replacement Parts Layout Large Parts: A. Fuselage HAN2926 B. Wing HAN2927 C. Side Force Generator HAN2928 D. Elevator/Stabilizer HAN2933 E. Rudder HAN2934 Items Not Shown: Fuel Tank Tail Wheel Assembly HAN2913 Decal Set HAN2932 Pushrod Set HAN2935 Landing Gear HAN2929 Wheels HAN2930 Additional Required Equipment...
  • Page 4: Additional Required Tools And Adhesives

    Additional Required Tools and Adhesives Tools Other Required Items • Flat blade screwdriver • Felt-tipped pen or pencil • Phillips screwdriver (small) • Measuring device (e.g. ruler, tape measure) • Crescent wrench • Covering Iron (HAN101) • Threadlock • Covering Glove (HAN150) •...
  • Page 5: Before Starting Assembly

    Before Starting Assembly Before beginning the assembly of your Tribute™ 36, remove each part from its bag for inspection. Closely inspect the fuselage, wing panels, rudder, stabilizer and side force generators for damage. If you find any damaged or missing parts, contact the place of purchase.
  • Page 6: Section 1: Receiver Installation

    Section 1: Receiver Installation Required Parts • Wing assembly • Radio hatch • 3mm x 12mm sheet metal screw (4) Required Tools and Adhesives • Phillips screwdriver (small)  Step 1 Wrap your receiver in foam to protect it from vibration. Place the receiver into the opening in the wing.
  • Page 7: Section 2: Installing The Stabilizer

    Section 2: Installing the Stabilizer Required Parts  Step 3 • Stabilizer assembly • Fuselage Attach the clevis to the elevator horn. With the radio on, • Stabilizer fixing screw (2) center the elevator servo. Thread the clevis in or out so the elevator is in neutral.
  • Page 8: Section 3: Landing Gear Installation

    Section 3: Landing Gear Installation Required Parts  Step 2 • Fuselage assembly • 3mm x 40mm bolt Slide the remaining landing gear half onto the bolts. • 3mm wing nut • Landing gear (2) Secure the gear using three 3mm wing nuts. Required Tools and Adhesives •...
  • Page 9: Section 4: Propeller And Spinner

    Section 4: Propeller and Spinner Required Parts  Step 3 • Fuselage • Propeller Locate the two #4 x 5/8" sheet metal screws. Position the • Spinner spinner cone onto the spinner backplate, making sure it keys into the backplate. Use the screws and a Phillips •...
  • Page 10: Section 5: Wing Installation

    Section 5: Wing Installation Required Parts  Step 3 • Wing • Fuselage Slide the side force generators into the wing. The one • 1/4-20 x 2" nylon bolt • Canopy hatch with the threaded rod slides in from the top. Secure the generators using the 3mm wing nuts.
  • Page 11: Adjusting The Engine

    Adjusting the Engine   Step 1 Step 3 Completely read the instructions included with your Before you fly, be sure that your engine idles reliably, engine and follow the recommended break-in procedure. transitions and runs at all throttle settings. Only when this is achieved should any plane be considered ready for ...
  • Page 12: Balancing The Model

    Balancing the Model Caution: Do not inadvertently skip this step! The recommended Center of Gravity (CG) range for the Tribute™ is 4 " behind the leading edge of the An important part of preparing the aircraft for flight is wing against the fuselage. It is suggested to start at the properly balancing the model.
  • Page 13: Notes

    Notes:...
  • Page 14: 2005 Official Ama National Model Aircraft Safety Code

    2005 Official AMA National Model Aircraft Safety Code GENERAL 7) I will not operate models with pyrotechnics (any device that explodes, burns, or propels a projectile 1) I will not fly my model aircraft in sanctioned of any kind) including, but not limited to, rockets, events, air shows or model flying demonstrations until explosive bombs dropped from models, smoke it has been proven to be airworthy by having been...
  • Page 15 2005 Official AMA National Model Aircraft Safety Code 5) Flying sites separated by three miles or more Organized RC Racing Event are considered safe from site-to site interference, 10) An RC racing event, whether or not an AMA Rule even when both sites use the same frequencies. Any Book event, is one in which model aircraft compete circumstances under three miles separation require in flight over a prescribed course with the objective of...
  • Page 16 � �� © 2005 Horizon Hobby, Inc. 4105 Fieldstone Road Champaign, Illinois 61822 (877) 504-0233 horizonhobby.com 7905...

Table of Contents