Oce TDS100 User Manual
  1. Manuals
  2. Brands
  3. Oce Manuals
  4. Printer
  5. TDS100
  6. User manual

Oce TDS100 User Manual

Hide thumbs Also See for TDS100:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual, Quick Reference Manual
Océ TDS100
User manual

Advertisement

Table of Contents
loading

Related Manuals for Oce TDS100

Summary of Contents for Oce TDS100

  • Page 1 Océ TDS100 User manual...
  • Page 2 Océ-Technologies B.V. Copyright © 2005, Océ-Technologies B.V. Venlo, The Netherlands All rights reserved. No part of this work may be reproduced, copied, adapted, or transmitted in any form or by any means without written permission from Océ. Océ-Technologies B.V. makes no representation or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose.

  • Page 3: Notes For The Reader

    Notes for the reader Introduction This manual helps you to use the Océ TDS100. The manual contains a description of the Océ TDS100 and guidelines to use and operate the Océ TDS100. There are also tips to increase your knowledge of the Océ TDS100 and to help you manage the workflow even better.
  • Page 4 User manual...

  • Page 5: Table Of Contents

    The operator panel of the sheet feed, single copy configuration 20 Chapter 2 Use the Océ TDS100 Turn on and off the Océ TDS100 24 Turn on and off the optional dew preventer 26 Copy on a media roll (automatic roll feed) 27...
  • Page 6 Appendix B Miscellaneous 61 Reader's comment sheet 62 Addresses of local Océ organisations 64 User manual...

  • Page 7: Introduction To The Océ Tds100

    Océ TDS100 User manual Chapter 1 Introduction to the Océ TDS100...

  • Page 8: The Documentation Set

    A short description on how to operate the ■ Quick Paper book Océ TDS100. reference guide A complete description on how to operate ■ User CD-ROM and maintain the Océ TDS100. manual Visit Océ on the internet at www.oce.com for more information. Note: User manual...

  • Page 9: The Configurations

    The configurations Introduction The Océ TDS100 is a wide format copier to copy large drawings. The Océ TDS100 is available in four different configurations. The following table displays these configurations with their functions and options. Functions and options per configuration [1] The Océ...

  • Page 10: The Components

    The components Introduction The following illustration displays the most complete configuration of the Océ TDS100, the automatic 2 roll feed configuration. Some options may not be available on your TDS100 due to the differences between the configurations. Illustration [1] The automatic 2 roll feed configuration of the Océ TDS100 [1] The automatic 2 roll feed configuration of the Océ...
  • Page 11 Middle cover Give access to the underside of the manual feed table. Some items may not be available on your Océ TDS100 due to the Note: differences between the configurations. Introduction to the Océ TDS100...

  • Page 12: The Operator Panel Of The Automatic 1 Roll And 2 Roll Feed Configuration

    The operator panel of the automatic 1 roll and 2 roll feed configuration Introduction You can identify your configuration by its operator panel. The following illustration displays the operator panel of the 1 roll and 2 roll configuration. User manual...
  • Page 13 1 2 3 4 toner media jam paper media film manual roll 1 feed roll 2 trailing strip leading synchro standard [2] The operator panel of the automatic 1 roll feed and 2 roll feed configuration Introduction to the Océ TDS100...
  • Page 14 The indicators Indicator Function 'Toner' Indicate that the Océ TDS100 has run out of toner. Green light Indicate that the copier is ready. A blinking green light indicates that the copier runs a copy job. Red light Indicate that an error has occurred.
  • Page 15 'Synchro' enables you to cut the copy to the same ■ size as the original. 'Standard' enables you to cut the copy to the same ■ size as a standard size. Use the adjustment key to set the standard size. Introduction to the Océ TDS100...
  • Page 16 Function Copies Adjust the number of copies. You can select a number of copies from 1 up to 9. When you press the stop key while the copier runs a ■ Stop copy job, the copy job will stop. When you press the stop key once while you set up ■...

  • Page 17: The Operator Panel Of The Sheet Feed, Multi Copy Configuration

    Illustration [3] The operator panel of the sheet feed, multi copy configuration 1 2 3 4 toner media jam paper media film trailing strip [3] The operator panel of the sheet feed, multi copy configuration Introduction to the Océ TDS100...
  • Page 18 The indicators Indicator Function 'Toner' Indicate that the Océ TDS100 has run out of toner. Green light Indicate that the copier is ready. A blinking green light indicates that the copier runs a copy job. Red light Indicate that an error has occurred.
  • Page 19 ■ a copy job, the number of copies returns to 1. When you press the stop key twice while you set up ■ a copy job, the default values return. Start Start the copy job. Introduction to the Océ TDS100...

  • Page 20: The Operator Panel Of The Sheet Feed, Single Copy Configuration

    The operator panel of the sheet feed, single copy configuration Introduction You can identify your configuration by its operator panel. The following illustration displays the operator panel of the single copy configuration. Illustration [4] The operator panel of the sheet feed, single copy configuration 1 2 3 4 toner media jam...
  • Page 21 The indicators Indicator Function 'Toner' Indicate that the Océ TDS100 has run out of toner. Green light Indicate that the copier is ready. A blinking green light indicates that the copier runs a copy job. Red light Indicate that an error has occurred.
  • Page 22 User manual...

  • Page 23: Use The Océ Tds100

    Océ TDS100 User manual Chapter 2 Use the Océ TDS100...

  • Page 24: Turn On And Off The Océ Tds100

    [5] The On / off switch at the back of the Océ TDS100 How to turn on the Océ TDS100 Set the On / off switch at the back of the Océ TDS100 to position 1. Result The green light at the operator panel illuminates and indicates that the Océ...
  • Page 25 How to turn off the Océ TDS100 Set the On / off switch at the back of the Océ TDS100 to position 0. Result The green light of the On / off switch is off and the green light at the operator panel is off.

  • Page 26: Turn On And Off The Optional Dew Preventer

    Turn on and off the optional dew preventer Introduction You are advised to use the optional dew preventer in an extreme humid environment to improve the copy quality in this condition. Illustration [6] The On / off switch of the dew preventer [6] The On / off switch of the dew preventer How to turn on the dew preventer Set the On / off switch at the back of the dew preventer to position 1.

  • Page 27: Copy On A Media Roll (Automatic Roll Feed)

    Set up your copy job at the operator panel Press the green start button. Before you begin Turn on the Océ TDS100. (see ‘Turn on and off the Océ TDS100’ on page 24). Feed strongly curled originals carefully, because the Océ Attention: TDS100 pulls in the original.
  • Page 28 Use the 'Cut' key to select the cut method. ■ Use the copies key to set the number of copies. ■ Press the green start button to start the copy job. Result The Océ TDS100 runs the copy job with automatic media feed. User manual...

  • Page 29: Copy On Cut Sheet Media (Manual Sheet Feed)

    Set up your copy job at the operator panel Press the green start button. Before you begin Turn on the Océ TDS100. (see ‘Turn on and off the Océ TDS100’ on page 24). Feed strongly curled originals carefully, because the Océ Attention: TDS100 pulls in the original.
  • Page 30 Use the copies key to set the number of copies ■ Press the green start button to start the copy job. Not available on the single copy configuration. Note: Result The Océ TDS100 runs the copy job with manual media feed. User manual...

  • Page 31: Adjust Leading And Trailing Strips

    Adjust leading and trailing strips Introduction Both originals and copies can contain a strip to file it. The Océ TDS100 allows you to handle strips as follows. Remove a strip ■ Add a strip. ■ You can adjust the following strips.
  • Page 32 How to add or remove a leading strip Place the original centrally and face down on the original feed table. The Océ TDS100 moves the original to the back. [10] Feed the original with leading strip centrally and face down...
  • Page 33 Use the adjustment key to add or remove a trailing strip. A positive value adds a strip, a negative value removes a strip. Press the green start button to start the copy job. Result The Océ TDS100 adds or removes a leading or a trailing strip. Use the Océ TDS100...

  • Page 34: Improve The Copy Quality Of Dark And Light Originals

    Improve the copy quality of dark and light originals Introduction You can use the exposure setting to improve the copy quality of a dark or light original. How to correct a dark original Use the exposure key to select a value between 0 and +4 to lighten the copy. How to correct a light original Use the exposure key to select a value between 0 and -4 to darken the copy.

  • Page 35: Check The Copy Quality With A Test Strip

    Press the 'Cut' key to select 'Standard' Press the upper side of the adjustment key The text 'TEST' appears on the display. Press the green start button to copy a strip. Result The Océ TDS100 copies only a strip of the original. Use the Océ TDS100...

  • Page 36: Straighten The Edge Of A Media Roll

    Straighten the edge of a media roll Introduction You can use the 'Cut' function to make the edge of a roll straight. Before you begin Remove the original from the original feed table. How to cut the edge of a roll Use the 'Feed' key to select a roll Use the 'Cut' key to select 'Standard' Press the upper side of the adjustment key.

  • Page 37: Maintain The Océ Tds100

    Océ TDS100 User manual Chapter 3 Maintain the Océ TDS100...

  • Page 38: Understand Message Codes

    Understand message codes Introduction The Océ TDS100 displays a message code when the copier is not ready to use. The following table shows a summary of the messages codes, the possible cause and the action to take. What the message code describes...

  • Page 39: Add Toner

    Add toner Introduction The Océ TDS100 illuminates the toner low indicator when the toner level is low. When the toner low indicator illuminates, you need to do the following. Add toner ■ Replace the waste toner bag. ■ If you ignore the toner low indicator, the copy quality will decrease.
  • Page 40 How to add toner and replace the waste toner bag Loosen the nut at the left back side. Open the left cover. [13] Open the left cover [13] Open the left cover Before you open the bottle, shake the bottle thoroughly. Put the toner bottle in the bottle holder.
  • Page 41 Close the left cover and tighten the nut at the left back side. Result The toner level of the Océ TDS100 is high, the toner low indicator is off and the wasted toner bag is removed. The Océ TDS100 is ready to copy.

  • Page 42: Clear An Original Jam

    Clear an original jam Introduction The media jam indicator blinks and the message code 'E 0' displays to indicate that an original jam occured. The type of original determines how to clear the original jam. The types of originals are divided into the following. Fragile originals ■...
  • Page 43 Check on a media jam also and clear the media jam if necessary. (see ‘Clear a media jam’ on page 44) Result The original jam is cleared and the media indicator is off. The Océ TDS100 is ready to copy. Maintain the Océ TDS100...

  • Page 44: Clear A Media Jam

    Clear a media jam Introduction The media jam indicator blinks and the message code 'E 3' displays to indicate that a media jam occured. A media jam can occur in one of the following sections The manual media feeder ■ The fuser section.
  • Page 45 Lift the manual feed table until you hear or feel a click Close the middle cover Check on an original jam also and clear the original jam if necessary.(see ‘Clear an original jam’ on page 42) Maintain the Océ TDS100...
  • Page 46 The fuser section can be hot. Caution: The jammed media can contain loose toner. Attention: Turn off the Océ TDS100 Loosen the nut at the left back side. Open the left cover. [20] Open the left cover [20] Open the left cover...
  • Page 47 Check on an original jam also and clear the original jam if necessary (see ‘Clear an original jam’ on page 42) Turn on the Océ TDS100. Result The media jam is cleared and the media indicator is off. The Océ TDS100 is ready to copy. Maintain the Océ TDS100...

  • Page 48: Replace A Media Roll

    Replace a media roll Introduction The media jam indicator blinks and the message code 'E 5' displays to indicate that a media roll is empty. When you replace a media roll, you need to check or set the following before you close the roll section. The media type ■...
  • Page 49 [24] Remove the roll holder Press the knob of the roll holder to remove the old media roll from the roll holder [25] Press the knob of the roll holder [25] Press the knob of the roll holder Maintain the Océ TDS100...
  • Page 50 Press the knob of the roll holder and slide the roll holder into the new roll. Press the knob of the roll holder to align the new roll with the correct media size on the roll holder. Place the roll holder with the new media roll in the drawer. Make sure you put the loose end of the media roll in the correct position.
  • Page 51 Press the knob of the roll holder and slide the roll holder into the new roll. Press the knob of the roll holder to align the new roll with the correct media size on the roll holder. Maintain the Océ TDS100...
  • Page 52 Place the roll holder with the new media roll in the drawer. Make sure you put the loose end of the media roll in the correct position. [30] Place the roll holder [30] Place the roll holder Feed the media as far as the wheels. Turn the wheels to feed the media as far as the arrow on the sticker.

  • Page 53: Clean The Transparent Plate

    'Océ cleaner A', part of cleaning kit with codenumber 1068117. 2 lint-free cloths Use 'Océ cleaner A' to reach the best results. Attention: Make sure you do not damage the sensor at the centre of the Attention: transparent plate. Maintain the Océ TDS100...
  • Page 54 How to clean the transparent plate Turn off the Océ TDS100 Pull the top cover towards you and lift the top cover to open it. [32] Open the top cover [32] Open the top cover Clean the transparent plate with a lint-free cloth and a small quantity of the...

  • Page 55: Overview And Tables

    Océ TDS100 User manual Appendix A Overview and tables...

  • Page 56: Default Values

    Introduction The default values of the settings are active in the following situations. Turn on the Océ TDS100 ■ Use the Océ TDS100 after sleep mode ■ Press the red stop key twice. ■ The default values of the settings of the sheet feed, single copy configuration...

  • Page 57: Product Specifications

    Product specifications Product specifications [2] The product specifications of the Océ TDS100 Feature Specification Copy process Dry indirect electrostatic Organic photo conductor Closed binary toner system Instant heating system Warm-up time None Copy speed 3 metres per minute Maximum media width 914 mm (36”)

  • Page 58: Supported Original Types And Sizes

    Supported original types and sizes Overview of supported original types and sizes [3] The supported original types and sizes of the Océ TDS100 Parameter Minimum value Recommended maximum value Width 210 mm (8.5”) 1000 mm (40”) Length 279 mm (10”) 3000 mm (10”)

  • Page 59: Supported Media Types And Sizes

    Océ systems and materials are matched for optimal quality and performance. You are therefore recommended to use only approved Océ materials in the Océ TDS100. A full list of Océ materials is suitable for use in the Océ TDS100. The list includes plain paper, transparent paper, coloured papers and different polyester films is available from your Océ...
  • Page 60 Overview of supported media The copy quality on the supported media can be less than on the recommended media. [6] The supported media types of the Océ TDS100. Media Supported type Remark Plain paper 100/110 g/m Transparent paper 60 g/m...

  • Page 61: Miscellaneous

    Océ TDS100 User manual Appendix B Miscellaneous...

  • Page 62: Reader's Comment Sheet

    Reader's comment sheet Questions Have you found this manual to be accurate? O Yes O No Were you able to operate the product, after reading this manual? O Yes O No Does this manual provide sufficient background information? O Yes O No Is the format of this manual convenient in size, readability and arrangement (page layout, chapter order, etc.)?
  • Page 63 Country: Please return this sheet to: Océ-Technologies B.V. For the attention of ITC User Documentation. P.O. Box 101, 5900 MA Venlo The Netherlands Send your comments by E-mail to: itc-userdoc@oce.nl For the addresses of local Océ organisations see: http://www.oce.com Miscellaneous...

  • Page 64: Addresses Of Local Océ Organisations

    Océ-Australia Ltd. Océ-Osterreich GmbH P.O. Box 363 Postfach 95 Ferntree Gully MDC 1233 Vienna Vic 3165 Austria Australia http://www.oce.at/ http://www.oce.com.au/ Océ-Belgium N.V./S.A. Océ-Brasil Comércio e Indústria Ltda. J. Bordetlaan 32 Av. das Nações Unidas, 11.857 1140 Brussel Brooklin Novo Belgium São Paulo-SP 04578-000...
  • Page 65 Océ-Deutschland GmbH Océ-Hong Kong and China head Solinger Straße 5-7 office 45481 Mülheim/Ruhr 12/F 1202 The Lee Gardens Germany 33 Hysan Avenue http://www.oce.de/ Causeway Bay Hong Kong http://www.oce.com.hk/ Océ-Hungaria Kft. Océ-Ireland Ltd. 1241 Budapest 3006 Lake Drive Pf.: 237 Citywest Business Campus...
  • Page 66 The addresses of local Océ organisations for information about the Wide Note: Format Printing Systems and the Production Printing Systems can be different from the addresses above. Refer to the web site http://www.oce.com for the addresses you need. User manual...
  • Page 67 cut (method, 1 & 2 roll configuration) 12 cut length (1 & 2 roll configuration) 12 Index dark original 34 default settings 56 default values 56 add toner 39 display (1 & 2 roll configuration) 12 adjustment key (1 & 2 roll configuration) 12 display (multi copy configuration) 17 adjustment key (multi copy configuration) 17 display (single copy configuration) 20...
  • Page 68 number of copies (1 & 2 roll configuration) 12 media jam 44 number of copies (multi copy configuration) 17 original jam 42 on / off switch 10 leading strip 31 operator panel 10 left cover 10 operator panel 1 & 2 roll configuration 12 light original 34 adjustment key 12 cut (method) 12...
  • Page 69 red light 20 start 20 stop 20 test strip 35 toner indicator 20 toner 39 options overview 9 toner indicator (1 & 2 roll configuration) 12 original feed table 10 toner indicator (multi copy configuration) 17 original jam 42 toner indicator (single copy configuration) 20 original sizes 58 top cover 10 original types 58...

Table of Contents