Page 3
Preface Notebook Computer W650SC Service Manual...
Page 4
Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent ven- dor.
Page 5
Preface About this Manual This manual is intended for service personnel who have completed sufficient training to undertake the maintenance and inspection of personal computers. It is organized to allow you to look up basic information for servicing and/or upgrading components of the W650SC se- ries notebook PC.
Page 6
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock and injury to per- sons when using any electrical equipment: 1. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer Do not place it on an unstable Do not place anything heavy...
Preface Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong mag- netic fields. These can hinder proper performance and damage your data. Take care when using peripheral devices. Use only approved brands of Unplug the power cord before peripherals.
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Related Documents You may also need to consult the following manual for additional information: User’s Manual on CD/DVD This describes the notebook PC’s features and the procedures for operating the computer and its ROM-based setup pro- gram. It also describes the installation and operation of the utility programs provided with the notebook PC. System Startup 1.
Preface Contents Introduction ..........1-1 Part List Illustration Location ............A-2 Top ....................A-3 Overview ..................1-1 Bottom ................... A-4 Specifications ..................1-2 DVD DUAL .................. A-5 External Locator - Top View with LCD Panel Open ......1-4 HDD ....................A-6 External Locator - Front & Right Side Views .........1-5 2nd HDD ..................
Page 12
Preface Lynx 4/9 ..................B-24 Lynx 5/9 ..................B-25 Lynx 6/9 ..................B-26 Lynx 7/9 ..................B-27 Lynx 8/9 ..................B-28 Lynx 9/9 ..................B-29 Mini PCIE, Fan Con ..............B-30 USB Charge, CCD, TPM, Power Con ......... B-31 eSATA/USB3.0, LED ..............B-32 Card Reader (RTL8411B) ............
Chapter 1: Introduction Overview This manual covers the information you need to service or upgrade the W650SC series notebook computer. Information about operating the computer (e.g. getting started, and the Setup utility) is in the User’s Manual. Information about dri- vers (e.g.
Introduction Specifications Processor Options LCD Options Intel® Core™ i7 Processor 15.6" (39.62cm) HD / FHD i7-4910MQ (2.90GHz) Video Adapter 8MB L3 Cache, 22nm, DDR3L-1600MHz, TDP 47W i7-4810MQ (2.80GHz), i7-4710MQ (2.50GHz) Intel® Integrated GPU and NVIDIA® Discrete GPU Latest Specification Information 6MB L3 Cache, 22nm, DDR3L-1600MHz, TDP 47W Supports Microsoft Hybrid Graphics The specifications listed here are correct at the...
Page 15
Introduction Interface Communication Dimensions & Weight One USB 2.0 Port Built-In Gigabit Ethernet LAN 374mm (w) * 252mm (d) * 14 - 31.4mm (h) Two USB 3.0 Ports 1.0M HD PC Camera Module One eSATA Port (USB 3.0 Combo) (Factory Option) 2.0M FHD PC Camera Module 374mm (w) * 249.5mm (d) * 14.8 - 32.8mm (h) One HDMI-Out Port (Factory Option) 3G or 4G M.2 Module...
Introduction External Locator - Top View with LCD Panel Open Figure 1 Top View 1. PC Camera 2. Built-In Microphone 3. *PC Camera LED *When the PC camera is in use, the LED will be illuminated in red. 4. LCD 5.
Introduction External Locator - Front & Right Side Views Figure 2 Front View 1. LED Indicator 2. Multi-in-1 Card Reader FRONT VIEW Figure 3 Right Side View 1. Microphone-In RIGHT SIDE VIEW Jack 2. Headphone-Out Jack 3. USB Ports 4. Optical Device Drive Bay 5.
Introduction External Locator - Left Side & Rear View Figure 4 Left Side View 1. DC-In Jack 2. Vent 3. External Monitor LEFT SIDE VIEW Port 4. RJ-45 LAN Jack 5. Combined eSATA/ USB 3.0 Port 6. HDMI-Out Port 7. USB 3.0 Ports Figure 5 REAR VIEW Rear View...
Introduction External Locator - Bottom View Figure 6 Bottom View 1. Battery 2. Component Bay Cover 3. Vent 4. Multi-in-1 Card Reader 5. Speakers Overheating To prevent your com- puter from overhea- ting, make sure no- thing blocks any vent while the computer is in use.
Introduction Mainboard Overview - Top (Connectors) Figure 9 Mainboard Top Connectors 1. CRT Port 2. RJ-45 LAN Jack 3. ESATA + USB 3.0 4. HDMI-Out Port 5. USB Port 3.0 Connector 6. Speaker Connector 7. Keyboard Cable Connector 8. TP Connector 9.
Chapter 2: Disassembly Overview This chapter provides step-by-step instructions for disassembling the W650SC series notebook’s parts and subsystems. When it comes to reassembly, reverse the procedures (unless otherwise indicated). We suggest you completely review any procedure before you take the computer apart.
Disassembly NOTE: All disassembly procedures assume that the system is turned OFF, and disconnected from any power supply (the battery is removed too). Maintenance Tools The following tools are recommended when working on the notebook PC: • M3 Philips-head screwdriver •...
Disassembly Maintenance Precautions The following precautions are a reminder. To avoid personal injury or damage to the computer while performing a re- moval and/or replacement job, take the following precautions: Power Safety Warning 1. Don't drop it. Perform your repairs and/or upgrades on a stable surface. If the computer falls, the case and other Before you undertake components could be damaged.
Disassembly Disassembly Steps The following table lists the disassembly steps, and on which page to find the related information. PLEASE PERFORM THE DISASSEMBLY STEPS IN THE ORDER INDICATED. To remove the Battery: To remove the 3G Module: 1. Remove the battery page 2 - 5 1.
Disassembly Removing the Battery Figure 1 Battery Removal 1. Turn the computer off, and turn it over. 2. Slide the latch in the direction of the arrow (Figure 1a a. Slide the latch and hold it 3. Slide the latch in the direction of the arrow, and hold it in place (Figure 1a in place.
Disassembly Removing the Keyboard Figure 2 Keyboard Removal 1. Turn off the computer, turn it over, remove the battery (page 2 - 2. Carefully press at point , from the bottom of the computer to unsnap the LED cover module (use the eject pin a.
Disassembly Removing the Hard Disk Drive Figure 3 HDD Assembly The hard disk drive can be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5mm Removal or 7mm (h). Follow your operating system’s installation instructions, and install all necessary drivers and utilities (as outlined in Chapter 4 of the User’s Manual) when setting up a new hard disk.
Page 32
Disassembly 4. Remove the component bay cover (Figure 4c Figure 4 5. Lift the HDD sponge up at point and grip the tab to slide the hard disk assembly in the direction of arrow HDD Assembly lift the hard disk assembly (Figure 4d Removal (cont’d.) 6.
Page 33
Disassembly Hard Disk Size Note (Foam Rubber Insert) Note that the hard disks pictured on the following pages are all 9.5mm(H) hard disk drives. In some cases 7mm(H) hard disk drives will be installed. For more information contact your distributor/supplier, and bear in mind your warranty terms.
Disassembly Removing the Optical (CD/DVD) Device Figure 6 Optical Device 1. Turn off the computer, and remove the battery (page 2 - Removal 2. Locate the component bay cover and remove screws (Figure 6a 3. Remove the component bay cover in the direction of the arrow (Figure 6b).
Page 35
Disassembly 6. Carefully pry the bezel off the optical device at point (Figure 7e Figure 7 7. Separate the bezel and the optical device. Optical Device 8. Reverse the process to attach the front bezel with the new optical device at point (Figure 7g).
Disassembly Removing the System Memory (RAM) Figure 8 RAM Module The computer has two memory sockets for 204 pin Small Outline Dual In-line Memory Modules (SO-DIMM) supporting Removal DDR3L up to 1600 MHz. The main memory can be expanded up to 16GB. The total memory size is automatically de- tected by the POST routine once you turn on your computer.
Page 37
Disassembly 5. Gently pull the two release latches ( & ) on the sides of the memory socket in the direction indicated by the Figure 9 arrows (Figure 9c). The RAM module will pop-up Figure 9d , and you can then remove it RAM Module 6.
Disassembly Removing and Installing a Processor Figure 10 Processor Removal Processor Removal Procedure 1. Turn off the computer, turn it over, remove the battery (page 2 - 5) and the component bay cover (page 2 - a. Locate the CPU heat sink.
Page 39
Disassembly 5. Turn the release latch towards the unlock symbol to release the CPU (Figure 11f). Figure 11 6. Carefully (it may be hot) lift the CPU up and out of the socket (Figure 11g). Processor Removal 7. Reverse the process to install a new CPU. (cont’d) 8.
Page 40
Disassembly Processor Installation Procedure Figure 12 Processor 1. Insert the CPU (Figure 12a), and pay careful attention to the pin alignment; it will fit only one way (DO NOT Installation FORCE IT!), and turn the release latch towards the lock symbol (Figure 12b).
Disassembly Removing the Wireless LAN Module Figure 13 Wireless LAN 1. Turn off the computer, turn it over, remove the battery (page 2 - 5) and the component bay cover (page 2 - Module Removal 2. The Wireless LAN module will be visible at point on the mainboard (Figure 13a).
Disassembly Wireless LAN, Combo, 3G & LTE Module Cables Note that the cables for connecting to the antennae on WLAN, WLAN & Bluetooth Combo, 3G and LTE modules are not labelled. The cables/covers (each cable will have either a black or transparent cable cover) are color coded for iden- tification as outlined in the table below.
Disassembly Removing the 3G Module Figure 14 3G Module Removal 1. Turn off the computer, turn it over, remove the battery (page 2 - 14) and the component bay cover (page 2 - 12). 2. The 3G module will be visible at point on the mainboard (Figure 14a).
Disassembly Removing and Installing the MSATA Module Figure 15 MSATA Removal Procedure MSATA Module Removal 1. Turn off the computer, remove the battery (page 2 - 14), and component bay cover (page 2 - 2. Locate the module, it is visible at point Figure 15a a.
Page 45
Disassembly MSATA Installation Procedure Figure 16 1. Place the thermal pad as shown (Figure 16a). MSATA Module 2. Insert the module in the computer Figure 16b Installation 3. Tighten the screw to secure it in place (Figure 16c). a. Place the thermal pad. b.
Disassembly Removing the CCD Figure 17 CCD Removal 1. Turn off the computer, turn it over, and remove the battery (page 2 - 14). 2. Run your fingers around the inner frame of the LCD panel at the points as indicated by the arrows a.
Page 47
Disassembly 5. Disconnect the cable (Figure 18d). Figure 18 6. Remove the CCD module (Figure 18e). CCD Removal 7. Reverse the process to install a new CCD module. (cont’d) d. Disconnect the cable. e. Remove the CCD mod- ule. 7.
Appendix A:Part Lists This appendix breaks down the W650SC series notebook’s construction into a series of illustrations. The component part numbers are indicated in the tables opposite the drawings. Note: This section indicates the manufacturer’s part numbers. Your organization may use a different system, so be sure to cross-check any relevant documentation.
Part List Illustration Location The following table indicates where to find the appropriate part list illustration. Table A - 1 Part List Illustration Part Location page A - 3 Bottom page A - 4 page A - 5 DVD Dual Drive page A - 6 page A - 7 2nd HDD...
Schematic Diagrams Appendix B: Schematic Diagrams This appendix has circuit diagrams of the W650SC notebook’s PCB’s. The following table indicates where to find the appropriate schematic diagram. Diagram - Page Diagram - Page Diagram - Page Table B - 1 System Block Diagram - Page B - 2 VGA I/O - Page B - 18 HDD, TP, Audio, USB - Page B - 34...
Schematic Diagrams VGA Frame Buffer Interface Frame Buffer Interface Term Description U33C U33C U33B U33B The total trace length measured BGA_0908_P080_P085_P100_290X290 BGA_0908_P080_P085_P100_290X290 Under GPU from GPU ball to capacitor is COMMON COMMON BGA_0908_P080_P085_P100_290X290 BGA_0908_P080_P085_P100_290X290 no more than 150 mil FBC_CMD[31:0] COMMON COMMON FBC_CMD[31:0]...
Schematic Diagrams VGA I/O U33M U33M U33K U33K U33L U33L BGA_0908_P080_P085_P100_290X290 BGA_0908_P080_P085_P100_290X290 COMMON COMMON BGA_0908_P080_P085_P100_290X290 BGA_0908_P080_P085_P100_290X290 BGA_0908_P080_P085_P100_290X290 BGA_0908_P080_P085_P100_290X290 COMMON COMMON COMMON COMMON Term Description 8/17 IFPEF 8/17 IFPEF 6/17 IFPC 6/17 IFPC 7/17 IFPD 7/17 IFPD The total trace length measured ALL PINS NC FOR GF117 ALL PINS NC FOR GF117 Under GPU...
BIOS Update Appendix C:Updating the FLASH ROM BIOS BIOS Version To update the FLASH ROM BIOS, you must: Make sure you down- • Download the BIOS update from the web site. load the latest correct version of the BIOS ap- •...
BIOS Update Use the flash tools to update the BIOS 1. Make sure you are not loading any memory management programs such as HIMEM by holding the F8 key as you see the message “Starting MS-DOS”. You will then be prompted to give “Y” or “N” responses to the programs being loaded by DOS.
Need help?
Do you have a question about the W650SC series and is the answer not in the manual?
Questions and answers