Advertisement
TEL: +86 20 82679969*816 FAX: +86 20 82684887 E-mail: scottchiu@gzxlscan.com
Address:
Unit137, the Pacific Industry Area, Xintang Town, Zengcheng District, Guangzhou, China
This Wireless Bar Code Scanner is an ingenious device with unique triggger
design and excellent performance. It is produced under advanced techniques, with
finest chipsets and fully conforms with ergonomics requirements. It is fast and
accurate in all 1D codes reading and programmed to better read incomplete or fuzzy
codes. It can be widely used in domains including commercial POS system,
supermarkets, warehousing and logistics, libraries, banks, transportation, postal
service, industrial and manufacturing process management.
It is represents an optical combination of proven high property scanning
technology and state-of-the-art ergonomics, featuring
-- Long-distant and fast transmission,
-- Scan number display,
-- Network construction, and
-- Application of Anti-jamming Frequency Hopping Technology.
NT-9600 brings convenience, comfort, high-speed and stability into your bar code
Guangzhou Netum Electronic Technology Co., Ltd
NT-9600 Wireless Barcode Scanner
Introduction
1
Advertisement
Table of Contents
Related Manuals for Netum NT-9600
Summary of Contents for Netum NT-9600
- Page 1 It is represents an optical combination of proven high property scanning technology and state-of-the-art ergonomics, featuring -- Long-distant and fast transmission, -- Scan number display, -- Network construction, and -- Application of Anti-jamming Frequency Hopping Technology. NT-9600 brings convenience, comfort, high-speed and stability into your bar code...
-
Page 2: Unpacking The Scanner
scanning. Features and Advantages 1. Never lose data, clear warning. 2. Intelligent uploading; can choose to upload data of last scans and resume uploading from breakpoints. 3. No-messy-code programmed, data counting, repeated code and out of the base range warning, ID display. 4. -
Page 3: Understanding The Features
4. If connection fails, unplug the base and repeat the above steps. Starting wireless scanning Scan the code “start wireless scanning” on the association cards or page 11 of the guide book. Understanding the features Audio and visual indications during data transmission: Successful communication Sound (beeper) Blue light... -
Page 4: Configuring The Scanner
transmits barcode message to the Host. 4. To instantly upload data, please make sure that the terminal is in range and associated to the base, or program will automatically turn into storage mode. The terminal communicates with the base at long distance of 150 meters indoor or 300 meters outdoor. - Page 5 Scan this code to enter Under this mode, the red light is Storage mode. on. The blue light will flash when a code is successfully read Under this mode, scans will Storage Mode and stored. be stored in the scanner. Scan this code to uploading stored data.
- Page 6 Scan this code to show total number of stored Show total number of scans. scans This counts by the number of Scan this code to show carriage return. number last stored scans. Note: this counter shows Show number of last scans new scan number after “uploading data of last operation”.
- Page 7 Set transmitter reporting to a named receiver. 1#, 2#... …100#, … e.g.: NT 122=200#, Set corresponding receiver 254# set corresponding receiver ID 200. Range: 1-254, end with #. Activate deactivate beeper function to indicate whether or not the signals are received during uploading data.
- Page 8 Display scanner ID at the receiving end. Enable scanner ID report Do not display scanner ID at Disable scanner ID the receiving end. report Set the delimiter between ID e.g.: scanner and barcode a Tab when ID ID=10, barcode= Set Tab between ID and report is enabled.
- Page 9 scanned. Disable repeated code detection. Note: this setting will automatically saved Disable repeated code remain detection effective after power failure. The above detecting time can be adjusted by scanning the following codes: (default: 6 seconds) Enter setting Set detecting time 6 seconds Set detecting time 5 seconds Set detecting time 4 seconds Set detecting time 3 seconds...
-
Page 10: Troubleshooting The Scanner
TEST 1234567890 Restore All Original Scanner Settings Start Wireless Scanning Display version information Troubleshooting the scanner This table lists potential problems and their solutions. Symptom Cause Solution The base does not When the reader is To restore normal mode, scan the normal upload data. - Page 11 associated to the base, cards or 6 page of this book. On the storage mode will be other hand, when instant uploading is automatically not needed, scan the storage mode code activated to replace below it to store scans. normal instant upload mode.
- Page 12 The battery pack Charge it. Full charging needs 3-5 hours power is lower than until the light turns into red. Clean the window with a cotton cloth The scanning moistened with an ammonia and water window solution. Dry with a soft cotton cloth or Scanner does not read dirty allow to air dry.
- Page 13 To construct a “many to one” network. 1) scan the code “enter setting” on the top of page 2) scan the code “display transmitter ID” on page 9, the reader will emit beeps. 3) put the reader close to the base and unplug the base for a few seconds and then plug back.
-
Page 14: Maintaining The Scanner
8) unplug the base for a few seconds then plug back. The flashing light and sounding beeper will stop. If they do not stop, the above setting is not successful. Scan the code “restore all original scanner settings” then the code “start wireless scanning”... - Page 15 by the Tel: Model: Series NO.: Seller Add: Purchase Date: Warranty Terms: a. This product is warranted against manufacturing defects in materials for a period of 1 year and workmanship for a period of 2 years from date of Manufacture, under normal use.