Below programming barcodes are applied for version - 2.4GWISX_20180514 Barcode Programming Netum barcode scanners are factory programmed for the most common terminal and communications settings. If you need to change these settings, programming is accomplished by scanning the bar codes in this guide. An asterisk (*) next to an option indicates the default setting.
Keyboard Language In order to let scanner upload the codes in a correct way, you have to set the keyboard language before you use it. For example If you use French Keyboard, first scan below barcode of “ Set Keyboard Language” then scan barcode of "French Keyboard", after that scanner will upload barcodes according to French keyboard layout.
Page 3
Scan Mode Trigger Mode (Default) Scanning this bar code will enable the scanner to enter manual trigger mode. Continuous Mode This mode enables the engine to scan/capture, decode and transmit over and over again. Auto Sense Mode Scanning this bar code will enable the scanner to enter auto sense mode. Terminator The scanner provides a shortcut for setting the terminating character suffix to CR or CRLF and enabling it by scanning the appropriate barcode below.
Working Mode If you are heading for a working area which lies outside the signal range, you may activate the offline mode of the scanner, following the steps described below. Under this enhanced offline mode, all scanned data will be stored directly into the buffer memory of the device.
Restore factory default Scanning the following barcodes one by one to restore the scanner to factory defaults. (Five steps included) 1. Factory Restore 2. Serial Port 3. Baud Rate 19200 4. Enter+LF 5. Setting Channel Scan channel 0, the scanner will have di di di di… sound. Take out the receiver and plug it again, later the di di sound will be stopped then you can start to scan the barcodes Channel 0...
Beep for Non-programming code Disables Scanner from beeping to indicate successful scans Enables to beep to indicate successful scan * Sleep Mode Enable Sleeping Immediately Prohibit Sleeping Idle Time Scanner will stay awake during the idle time that you set for it and turn to sleep if you haven't used it during the whole idle time.
Custom prefix and suffix Custom Prefix Custom Suffix 1 Custom Suffix 2 Please note previous prefix or suffix will be cleared once you start to add new prefix or suffix. Scan Data Transmission Format To change the Scan Data Transmission Format, scan one of the eight bar codes corresponding to the desired format.
Page 8
Appendix Numeric Bar Codes For parameters requiring specific numeric values, scan the appropriately numbered bar code(s). For Example Custom @ as prefix Step 1: scan “custom prefix”...
Page 9
Custom Prefix Step 2: To set these values, scan a four-digit number (i.e. four bar codes) that corresponds to ASCII values. See Numeric Bar Codes in appendix 1. Scan 1043(@) one by one. Step 4: Set Data Transmission Format <PREFIX> <DATA > Custom Suffix Step 1: scan “custom suffix”...
Page 10
<DATA><SUFFIX 1> Enable Keystroke*/ Functional Key Set Enable Keystroke* Enable functional Key For example if you scan value 1004, Keystroke will be “Up Down”. But if you scan Enable Functional Key Set after you scan the value ” 1004”, you will get functional key set Ctrl +D. For more details please refer to Appendix 1.
Page 11
Appendix Scan Value Hex Vaule Keystorkes Functional Key Set 1007 Enter Ctrl+G 1008 Left Arrow Ctrl+H 1003 Right Arrow Ctrl C 1004 Up Down Ctrl D 1010 Down Arrow Ctrl+J 1009 Horizontal Tab Ctrl+I 1011 Veritical Tab Ctrl+K 1012 Backspace Ctrl+L 1014 Insert...
Page 12
Common function Barcodes Enable/Disable UPC-E 1000021 1000020 *Enable UPC-E Disable UPC-E Enable/Disable EAN-8 1000041 1000040 *Enable EAN-8 Disable EAN-8 Enable/Disable EAN-13 1000031 1000030 *Enable EAN-13 Disable EAN-13 Enable/Disable Bookland EAN(ISBN) 1000231 1000230 Enable Bookland EAN *Disable Bookland EAN Decode UPC/EAN Supplementals UPC/EAN Supplementals are bar codes appended according to specific format conventions (e.g.UPC A+2, UPC E+2, EAN 13+2, EAN 13+5).
• Only read the barcode with supplementals- The scan engine can only read the barcode with supplementals. 2010E01 Decode UPC/EAN with Supplementals • Auto read supplementals- The scan engine can not only read the barcode with supplementals,but also read the barcode without supplementals. 2010E02 Auto discriminate UPC/EAN Supplementals Eable/Disable Code 128...
Page 16
Appendix Full ASCLL Code Scan Value Hex Value Keystroke 39 Encode Char CTRL 2 1000 CTRL A 1001 1002 CTRL B 1003 CTRL C CTRL D 1004 1005 CTRL E 1006 CTRL F CTRL G 1007 1008 CTRL H 1009 CTRL I CTRL J 1010...
Page 17
Full ASCLL Code Scan Value Hex Value Keystroke 39 Encode Char 1025 CTRL Y CTRL Z 1026 CTRL [ 1027 1028 CTRL \ CTRL ] 1029 1030 CTRL 6 1031 CTRL - Space Space 1032 1033 ‘ 1034 1035 1036 1037 &...
Page 20
Full ASCLL Code Scan Value Hex Value Keystroke 39 Encode Char 1118 1119 1120 1121 1122 1123 1124 1125 1126 Undefined 1127 Support For any inquiries concerning our products, please send an email to service@gzxlscan.com, and we will respond to you as soon as possible. Contact Information Tel.:+0086 20-6626-0708 Email:service@gzxlscan.com...