Netum NT-W3 Quick Setup Manual
  1. Manuals
  2. Brands
  3. Netum Manuals
  4. Barcode Reader
  5. NT-W3
  6. Quick setup manual

Netum NT-W3 Quick Setup Manual

Hide thumbs

Advertisement

Table of Contents

NT-W3
Quick Setup Guide
This is a plug and play model if you use a US keyboard. If you use other type of keyboard, plug the
USB cable on your device , setup keyboard language before you use it. (refer to below Keyboard
Language Type) after that the scanner can start to work.
If you want to do other configurations please refer to below programming barcodes.

Barcode Programming

Netum barcode scanners are factory programmed for common terminal and communications
settings. If you need to change these settings, programming is accomplished by scanning the bar
codes in this guide. An asterisk (*) next to an option indicates the default setting.

Firmware Version

Read below command barcode to check scanner firmware version.
If you have any questions about the scanner, please scan above barcode
Keyboard Language
In order to let scanner upload the codes in a correct way, you have to set the keyboard
language.
For example
000A0
Firmware Version

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the NT-W3 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Netum NT-W3

Summary of Contents for Netum NT-W3

  • Page 1: Barcode Programming

    If you want to do other configurations please refer to below programming barcodes. Barcode Programming Netum barcode scanners are factory programmed for common terminal and communications settings. If you need to change these settings, programming is accomplished by scanning the bar codes in this guide.
  • Page 2 If you use French Keyboard, scan below barcode of “French keyboard” then scanner will upload barcodes according to France keyboard layout. American Keyboard is set by default, if you use a US keyboard you can skip this step. American Keyboard Portugal Keyboard French Keyboard Spanish Keyboard...

  • Page 3: Scanning Mode

    Scanning Mode · Key Holding Press the button to trigger the reading, release the button to end the reading. Reading success or reading time over a single reading time will end the reading. 013300 By trigger · Continuous Mode Under continuous mode scanner performs continuous work. Reading success or reading time over a single reading time will end the reading.

  • Page 4: Default Configuration

    Reader Beep Tone 014201 014200 Beep Tone ON Beep Tone OFF Default Configuration If you want to cancel all the configuration that you have done to the scanner. Scan below barcodes to the restore factory. 000B0 Factory Default Common Function Barcodes EAN-8 00371 00370...

  • Page 5: Transmit Check Digit

    Transmit Check Digit EAN-8 is 8 digits in length with the last one as its check digit used to verify the integrity of the data. The default mode opens “transmit EAN-8 Check Digit”. Users can scan the code below to choose it.
  • Page 6 00461 00460 Transmit EAN-13 Check Digit* Do Not Transmit EAN-13 Check Digit Add-On Code And EAN-8/EAN-13 Barcode can be augmented with a two-digit or five-digit add-on code form a new one. In the example below, the part surrounded by blue line is an EAN-8 barcode while the part circled by red line is add-on code.
  • Page 7 EAN-13 Transfer to ISSN An International Standard Serial Number (ISSN) is used to uniquely identify a serial publication. When you scan “EAN-13 Transfer to ISSN”programming code, the output code will be 10 digits long ISSN code. The default closes this mode. 01501 01500 Enable EAN-13 Transfer to ISSN...
  • Page 8 Full ASCII 00231 00230 Enable Full ASCII* Disable Full ASCII Code 93 00621 00620 Enable Code 93* Disable Code 93 Code128 00691 00690 Enable Code 128* Disable Code 128 GS1 DataBar Limited (RSS Limited) 01771 01770 Enable RSS Limited Disable RSS Limited* GS1 DataBar Ominidirectional (RSS Ominidirectional) 01671 01670...
  • Page 9 UPC-A 00341 00340 Enable UPC-A * Disable UPC-A Transmit Check Digit UPC-A is 12 digits in length with the last one as its check digit used to verify the integrity of the data. The default mode opens “Transmit UPC-A Check Digit”. Users can choose to send it or not. 00421 Transmit UPC-A Check Digit* 00420...
  • Page 10 UPC-A Transfer to EAN-13 00391 00390 Enable UPC-A Transfer to EAN-13 Disable UPC-A Transfer to EAN-13 UPC-E 00351 00350 Enable UPC-E Disable UPC-E Add –On Code Setting In the example below ,the part surrounded by blue line is a UPC-A barcode while the part circled by red line is add-on code.
  • Page 11 Industrial 2 of 5 01061 01060 Enable Industrial 2 of 5* Disable Industrial 2 of 5 Standard 2 of 5 01871 01870 Enable Standard 2 of 5 Disable Standard 2 of 5 Matrix 2 of 5 01461 01460 Enable Matrix 2 of 5* Disable Matrix 2 of 5 01151 01150...
  • Page 12 Plessey 01161 01160 Enable Plessey Disable Plessey* Add-On Code Setting Users can scan the code below to open or close the setting of UPC/EAN/JAN. 00551 00552 Enable 2-Digit Add-On Code Enable 5-Digit Add-On Code 00553 00550 Enable2&5 Digit Add-On Code Disable Digit Add-On Code*...

  • Page 13: Code Id Setting

    Code ID Setting Users usually need to know barcode type in the process of scanning, you can use Code ID prefix to recognize the barcode type. Please read “Appendix A” for the reference of the Code ID corresponding barcode type. No Code ID default setting. 01400 Enable Code ID* 01401...
  • Page 14 Custom Prefix 02240 02220 Custom Prefix Clear all prefix Custom Suffix 02241 02220 Custom Suffix Clear all suffix 02242 Exit Custom Prefix and Suffix Custom Prefix Step 1 : Scan code of 02240 ( add prefix ) Note: This step will clear all previous setting. Maximum you can add 32 character. 02240 Step 2 : Scan relevant barcode of the prefix that you want to add from Appendix For example: If you want to add “MG”as the prefix...
  • Page 15 Step2: Scan “M”, then scan “G” 1077 1071 Clear all prefix Scan clear all prefix (02220), then all previous prefix configuration will be cleared. 02220 Add Suffix Step 1 : Scan code of 02241 ( add suffix ) 02241 Note: This step will clear all previous setting. Maximum you can add 32 characters.
  • Page 16 Appendix A Code ID Type of Code(For Prefix &Suffix) Symbology All Symbologies CODE 128 EAN 8 EAN 13 UPC-A UPC-E CODE 93 GS1 Omnidirectional GS1 Limited CODE 39 Interleaved 2 of 5 Industrial 2 of 5 Standard 2 of 5 Matrix 2 of 5 Plessey CODE 11...

  • Page 17: Appendix B（Ascii Table

    Appendix B（ASCII Table） 1001 1002 1003 SOH（01） STX（02） ETX（03） 1004 1005 1006 EOT（04） ENQ（05） ACK（06） 1007 1008 1009 BEL（07） Backspace（08） HT （09） 1010 1011 1012 LF（0A） VT（0B） FF（0C） 1013 1014 1015 CR（0D） SO（0E） SI（0F） 1016 1017 1018 DEL（10） DC1（11） DC2（12） 1019 1020 1021...
  • Page 18 1025 1026 1027 EM（19） SUB（1A） ESC（1B） 1028 1029 1030 FS（1C） GS（1D） RS（1E） 1031 1032 1033 US（1F） Space（20） !（21） 1034 1035 1036 #（23） $（24） “（22） 1037 1038 1039 %（25） &（26） ‘（27） 1040 1041 1042 (（28） )（29） *（2A） 1043 1044 1045 +（2B） ,（2C）...
  • Page 19 1049 1050 1051 1（31） 2（32） 3（33） 1052 1053 1054 4（34） 5（35） 6（36） 1055 1056 1057 7（37） 8（38） 9（39） 1058 1059 1060 ;（3B） <（3C） :（3A） 1061 1062 1063 =（3D） >（3E） ?（3F） 1064 1065 1066 @（40） A（41） B（42） 1067 1068 1069 C（43） D（44）...
  • Page 20 1073 1074 1075 I（49） J（4A） K（4B） 1076 1077 1078 L（4C） M（4D） N（4E） 1079 1080 1081 O（4F） P（50） Q（51） 1082 1083 1084 S（53） T（54） R（52） 1085 1086 1087 U（55） V（56） W（57） 1088 1089 1090 X（58） Y（59） Z（5A） 1091 1092 1093 [（5B） \（5C）...
  • Page 21 1097 1098 1099 a（61） b（62） c（63） 1100 1101 1102 d（64） e（65） f（66） 1103 1104 1105 g（67） h（68） i（69） 1106 1108 k（6B） l（6C） j（6A） 1109 1110 1111 m（6D） n（6E） o（6F） 1112 1113 1114 p（70） q（71） r（72） 1115 1116 1117 s（73） t（74） u（75）...
  • Page 22 1121 1122 1123 y（79） z（7A） {（7B） 1124 1125 1126 |（7C） }（7D） ~（7E） 1127 Delete（7F）...

Table of Contents