Spectra T50e Quick Start Manual

Power cord
1
Ethernet cable
U
NPACK AND
V
ERIFY THE
C
OMPONENTS
Rubber feet
Remove the library from its shipping box.
Warning!
2
people or a lift to move or lift the library.
Warnung!
müssen zwei Personen oder einen Aufzug zu bewegen oder heben Sie
die Bibliothek.
I
NSTALL THE
Important!
L
IBRARY
The library can be used either installed in a rack or placed on a tabletop.
Rack-mount Installation.
Installation Guide
Important!
Tabletop Installation.
1.Carefully place the library on its side, but do not damage the bracket.
2.Remove the paper backing from the six feet and install as shown.
3.Place the library on a level surface in a well ventilated location.
Caution!
robot movement.
Follow these steps to remove the shipping key:
Caution!
3
library can cause damage to the internal components.
Caution!
can cause damage to the internal components. Make sure the library
R
EMOVE THE
is installed using one of the methods described in
S K
HIPPING EY
before removing the shipping key.
1.Remove the tape securing the shipping key and pull the key straight up
and out of the library.
2.Place the tape back over the opening in the top of the library.
3.Store the key in the tab at the back of the library.
Install the tape drives in the back of the library, from bottom to top.
1.Loosen the finger screws securing the cover plate (or plates), which must
4
be removed to install the drives. Remove one cover plate for each half-
height drive.
Important!
2.Remove the plate and set it aside.
I
NSTALL THE
T D 3.Remove the tape drive and sled from its protective packaging.
APE RIVES
4.While supporting the bottom of the drive sled, slide it into the empty
drive bay. Push the drive sled in until it fits flush against the chassis.
5.Tighten the finger screws to secure the drive to the library.
6.Repeat for any additional drives.
If your library shipped with optional expansion slots, see the
Library User Guide
Power
library shipped with the optional redundant power supply, connect a
5
power cord to the redundant supply and to an outlet.
Fibre Channel Drives
1.Remove the protective plugs from the optical connector.
C
ONNECT THE
2.Insert one end of the FC cable into the tape drive.
C
ABLES
3.Insert the other end of the cable into the FC switch or host HBA.
SAS Drives
drive and the other end into the host SAS HBA.
Ethernet
back of the library and connect the other end to the host network.
© 2010 — 2015 Spectra Logic Corporation. All rights reserved worldwide. BlueScale, CC, Spectra, SpectraGuard, Spectra Logic, TeraPack, and TranScale are registered trademarks of Spectra Logic Corporation. ArchiveGrade,
BlackPearl, IntraCloud, nTier Verde, and Verde are trademarks of Spectra Logic Corporation. All rights reserved worldwide. All other trademarks and registered trademarks are the property of their respective owners.
S
PECTRA
Q
UICK
Document Kit
Open This First
USB device
(in document kit)
The library weighs approximately 34.4 lb. You may need two
Die Bebliothek hat ein Gewicht vonungefähr 15,6 kg. Sie
Lift the library only by the sides—not by the front and back.
Refer to the Spectra T50e Rack-mount Kit
on the Technical Support portal.
Do not install the feet if you are rack-mounting the library.
You do not need to remove the brackets.
Do not stack items on top of the library, as they can restrict
Failure to remove the shipping key before powering on the
Removing the shipping key and then moving the library
Cover plates must remain installed over any empty drive bays.
for installation instructions.
Connect the power cord to the library and to an outlet. If the
(not shown) Insert one end of the SAS cable into the tape
Connect an Ethernet cable into the Ethernet connector on the
T50e L
IBRARY
S G
TART UIDE
Half Height (HH) tape drive in drive sled*
* The tape drives, the (optional) redundant power
supplies, and the library may ship and
arrive at your site separately.
Alignment
mark (6x)
1 Access bottom
2 Attach six feet
1 Remove tape
and key

Install the Library

2 Replace tape
3 Store key
1
Loosen screws
2 Remove plate
Remove tape drive
3
from packaging
4 Install tape drive
Spectra T50e
5 Tighten screws
Remove plugs
1
Connect
2
FC
Connect cables
3
to FC switch or host HBA
E Ethernet
Rack-mount kit
Important! If you remove the brackets, replace the
black screws; do not replace the silver screws.
Bottom of library
P Power
cables
Do not set
the library on
the brackets