Page 2
Precaucion calificado. En el interior no hay partes a las que el usuario deba acceder. Para particular use. In no event will Extron Electronics be liable for direct, indirect, or evitar riesgo de electrocución, no intentar personalmente la reparación/ Leer las instrucciones • Leer y analizar todas las instrucciones de...
Page 4
Step 3 Attach output cables to the rear (CVEQ1)/bottom (CVEQ1 AAP)/ side (CVEQ1 WM) panel of the line driver and to the output devices. See “Rear/Bottom/Side Panel Features and Cabling” in chapter 2. Step 4 Attach input cables to the input devices and to the line driver’s front panel connectors.
Disconnect the input and output devices’ power. Rear/Bottom/Side Panel Features and Cabling ..2-6 C. For the CVEQ1 WM, secure the faceplate onto the UL-approved Top/Side Panel Features and Adjustments ....2-8 electrical wall box in the wall or furniture.
Vertrieb von CAMBOARD Electronics Table of Contents, cont’d CVEQ1, CVEQ1 WM, CVEQ1 AAP Chapter One Introduction About the CVEQ1, CVEQ1 WM, and CVEQ1 AAP Features www.camboard.de Tel. 07131 911201 ce-info@camboard.de CVEQ1 Series • Table of Contents Fax 07131 911203...
five-pole captive screw connector provides for stereo audio output. The Extron CVEQ1 AAP is identical to the CVEQ1, except that it is designed to be mounted in a double-space height architectural adapter plate bracket (in a device’s faceplate or in an AAP wallplate) for installation into a wall or furniture.
Insert the wall box into the opening, and attach it to the • The CVEQ1 AAP can be installed in an Extron two-gang, four- wall stud or furniture with nails or screws, leaving the gang, or half rack width AAP Architectural Adapter Plate or in front edge flush with the outer wall or furniture surface.
(Signal) Sleeve (Gnd) right. Faceplate screws (CVEQ1 WM and CVEQ1 AAP only) — These screws fasten the line driver’s faceplate to the rest of the line driver. Do not remove these faceplate screws while the line driver is attached to the wall/furniture or the detached line driver may fall down into the electrical box.
Rear/Bottom/Side Panel Features and Cabling Video output connector — Using a coaxial cable, connect a display device to this female BNC connector. For the CVEQ1 WM and CVEQ1 AAP, the BNC is at the end of a short pigtail on the circuit board. CVEQ1...
Adjust the gain and equalization before installing the CVEQ1 AAP or CVEQ1 WM into a wall or furniture, as the gain and equalization adjustment Stereo Audio controls will be inaccessible after installation.
The CVEQ1 WM must have output cables connected before it to a device’s faceplate or an AAP wallplate and cabled before the is installed in a wall or furniture. Secure the CVEQ1 WM to the device or wallplate is installed in a wall or furniture. The screws wall box as shown below.
Video Connectors Gain ........... -6 dB to +6 dB, adjustable: 0.5 V to 2.0 V CVEQ1 ........(1) 3.5 mm captive screw connector, 5 pole ±10% with input at 1 volt CVEQ1 AAP......(1) 3.5 mm direct insertion captive screw Equalization/peaking gain ...
CVEQ1, CVEQ1 WM, CVEQ1 AAP All nominal levels are at ±10%. Specifications are subject to change without notice. Included Parts These items are included in each order for a CVEQ1, CVEQ1 AAP, or CVEQ1 WM: Included parts Part number CVEQ1...
Circuit Board C'SINK NEAR SIDE 0.000 (2 PLACES) Cut Out Line for Installing the Electrical Box TEMPLA TE IS NOT FULL SIZE. www.camboard.de Tel. 07131 911201 ce-info@camboard.de CVEQ1 Series • Dimensions, Templates CVEQ1 Series • Dimensions, Templates Fax 07131 911203...
Need help?
Do you have a question about the CVEQ1 and is the answer not in the manual?
Questions and answers