Advertisement
Quick Links
IMPORTANT: RETAIN THIS MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE.
Broiler area must be kept free of combustible materials, and the flow of combustion and ventilation air
must not be obstructed. Operating personnel must not perform any maintenance or repair functions.
Contact your Nieco Authorized Dealer.
Do not store or use gasoline or other flammable vapors or
liquids in the vicinity of this or any other appliance.
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
CONTROLS AND INDICATORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
PARTS AND LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
CLEANING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
CONVEYOR BELT REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
TROUBLE SHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
AUTOMATIC
FOODSERVICE
EQUIPMENT
FLEXI-CHEF SYSTEM
AUTOMATIC ELECTRIC BROILER
MODEL 615E
OPERATING
INSTRUCTIONS
FOR YOUR SAFETY:
TABLE OF CONTENTS
®
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Nieco Flexi-Chef System 615E
Summary of Contents for Nieco Flexi-Chef System 615E
-
Page 1: Table Of Contents
Broiler area must be kept free of combustible materials, and the flow of combustion and ventilation air must not be obstructed. Operating personnel must not perform any maintenance or repair functions. Contact your Nieco Authorized Dealer. FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance. -
Page 2: Installation
INSTALLATION PRE-INSTALLATION Uncrate the broiler, and inspect for shipping damage. Contact the factory if there is obvious damage. Remove the tape securing the machine parts, and install the parts in their proper location. If you find concealed damage to any part of this unit, contact your freight carrier immediately. -
Page 3: Controls And Indicators
CONTROLS AND INDICATORS MODEL 615E OR 815E A. 5 Amp fuse D. Digital Speed Controller (2 - 615, 3 - 815) B. Power On Indicator Light (Red) E. Motor On/Off Switches (White) (2 - 615, 3 - 815) C. Main Power On/Off Switch (Red) STARTING PROCEDURE Before starting broiler, ensure that all parts are installed in the proper location, the plug is properly inserted in the socket, and the ventilation hood is turned on. -
Page 4: Parts And Location
PARTS AND LOCATION MODEL 615E - FEED END VIEW... - Page 5 PARTS AND LOCATION MODEL 615E - FRONT SIDE VIEW...
-
Page 6: Cleaning Instructions
• The motors contain carbon brushes which will eventually need to be replaced. If you notice that your motor is running loud, occasionally tripping the breaker switch, or causing the conveyor to move erratically, replace the motor brushes. Contact your Nieco Authorized Distributor for replacement brushes. -
Page 7: Conveyor Belt Removal
CONVEYOR BELT REMOVAL 1. Run the conveyor belt until the master link is located near the drive shaft. (The master link has a BELT shorter knuckle, to allow CONVEYOR BELT DIRECTION it to be uncoupled easily.) MASTER LINK FEED END 2. -
Page 8: Wiring Diagram
WIRING DIAGRAM... -
Page 9: Trouble Shooting Guide
TROUBLE SHOOTING GUIDE Identify the problem in the left column, and look for probable causes and solutions in the right hand columns. Probable causes are listed in “most likely to happen” order. This sequence should be used to isolate the problem. Once the cause is found, refer to OPERATION and PARTS AND LOCATION sections for explanation of function or repair part needed. - Page 10 PROBLEM PROBABLE CAUSE SOLUTION 9. Broiled product sticks to 1. Stripper blades not adjusted or installed 1. Adjust or install properly. conveyor belt. properly. 2. Product under broiled. 2. Decrease motor speed. 3. Elements too cool. 3. Check elements. 4. Heat reflectors not installed or installed 4.
-
Page 11: Specifications
SPECIFICATIONS... - Page 12 Nieco Corporation • 7950 Cameron Drive • Windsor, CA 95492 • 707.284.7100 Office • 707.284.7430 Fax 8/94 • www.nieco.com • service@nieco.com • Printed in the USA...
Need help?
Do you have a question about the Flexi-Chef System 615E and is the answer not in the manual?
Questions and answers