Table of Contents
Advertisement
Quick Links
AUTOMATIC
FOODSERVICE
EQUIPMENT
AUTOMATIC ELECTRIC
BROILER
MODELS 824E & 850E and 624E & 650E
"B-Series Broiler"
OWNER'S MANUAL
FOR YOUR SAFETY:
Do not store or use gasoline or other flammable vapors or
liquids in the vicinity of this or any other appliance.
IMPORTANT: RETAIN THIS MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE
Broiler area must be kept free of combustible materials, and the flow of combustion and ventilation air must not
be obstructed. Operating personnel must not perform any maintenance or repair functions. Contact your Nieco
Authorized Dealer.
Advertisement
Table of Contents
Related Manuals for Nieco 824E
Summary of Contents for Nieco 824E
- Page 1 IMPORTANT: RETAIN THIS MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE Broiler area must be kept free of combustible materials, and the flow of combustion and ventilation air must not be obstructed. Operating personnel must not perform any maintenance or repair functions. Contact your Nieco Authorized Dealer.
-
Page 3: Table Of Contents
TABLE OF CONTENTS Machine Installation ...................4 Pre-Installation Mounting Hood Requirements Clearance Electrical Connection Pre-Operation Check Operation......................5 Controls and Indicators Broil Stabilizer Control Conveyor Belt Speed Step-by-Step Starting Procedure Shutdown Procedure Parts and Location .....................8 824/850 624/650 Cleaning.......................14 Periodic Maintenance ..................14 Conveyor Belt Removal..................15 Conveyor Belt Tension ..................16 Broil Belt Problems... -
Page 4: Pre-Installation
A. INSTALLATION PRE-INSTALLATION Uncrate the broiler, and inspect for shipping damage. Contact the factory if there is obvious damage. Remove the tape securing the machine parts, and install the parts in their proper location. Refer to the Parts and Location section of this manual. If you find concealed damage to any part of this unit, contact your freight carri- er immediately. -
Page 5: Operation
No daily adjustment of the Broil Stabilizer Control is necessary. FOOD PRODUCT SAFETY The Nieco broiler is designed to cook food consistently. Careful setting of the conveyor belt speed is necessary for proper performance. Always test the product to be sure it is cooked properly every... - Page 6 Action ER 4 Turn power on and off several times. If the message remains, replace control. If the message disappears, the control may need to be reprogrammed. Call Nieco or your local distributor for instructions. ER 6 Cycle power on and off several times. If message remains, replace temperature...
-
Page 7: Step-By-Step Starting Procedure
Before starting broiler, be sure that all parts are installed in the proper location, and the ventilation hood is turned on. STEP-BY-STEP STARTING PROCEDURE 1. Turn on Main Power by turning the Main Power Switch to the right. 2. Turn on Motor Power Switch (A) and set Motor Speed Control (B) to desired set- ting. -
Page 8: Parts And Location
C. PARTS AND LOCATION Models 824 & 850 Electric - Feed End View... - Page 9 PARTS AND LOCATION Models 824 & 850 Electric - Left Side View...
- Page 10 PARTS AND LOCATION Models 824 & 850 Electric - Right Side View...
- Page 11 PARTS AND LOCATION Models 624 & 650 Electric - Feed End View...
- Page 12 PARTS AND LOCATION Models 624 & 650 Electric - Left Side View...
- Page 13 PARTS AND LOCATION Models 624 & 650 Electric - Right Side View...
-
Page 14: Cleaning
D. CLEANING INSTRUCTIONS DAILY CLEANING Clear broiler of all food product before shutting down to clean. Allow broiler to cool before handling parts. 1. SHEET METAL PARTS. Remove all trays, drip pans, stripper blades, reflectors, and side panels. Wash with water and an approved detergent. Sanitize. 2. -
Page 15: Conveyor Belt Removal
F. CONVEYOR BELT REMOVAL Before beginning, notice the way the belt runs through the broiler. Also notice the direction the knuckles face. Be sure to re-assemble in the same way. 1. Run belt until the Master Link is near the front idler shaft. 2. -
Page 16: Conveyor Belt Tension
G. CONVEYOR BELT TENSION Maintain proper tension on the conveyor belts to prevent jamming. Bearing spacers (pictured below) are supplied with the broiler to make minor tension adjustments. Major tension adjustments are made by removing a link or links from the belt. The diagram on the left shows the spacer in the stored position. -
Page 17: Trouble Shooting Guide
H. TROUBLE SHOOTING GUIDE Identify the problem in the left column, and look for probable causes and solutions in the right hand columns. Probable causes are listed in “most likely to happen” order. This sequence should be used to isolate the problem. Once the cause is found, refer to OPERATION and PARTS AND LOCATION sections for explanation of function or repair part needed. - Page 18 PROBLEM PROBABLE CAUSE SOLUTION 7. Conveyor speeds are 1. SCR loose or defective. 1. Plug in or replace. erratic. 2. Speed control pot defective. 2. Replace. 3. Drive chain binding. 3. Adjust chain tension. Lubricate. 4. Gear motor defective. 4. Replace. 5.
-
Page 19: Wiring Diagram
I. WIRING DIAGRAM Model 824/850 Electric / Domestic (U.S.A.) - Page 20 WIRING DIAGRAM Model 824/850 Electric / International (Export)
- Page 21 WIRING DIAGRAM Model 624/650 Electric / Domestic (USA)
- Page 22 WIRING DIAGRAM Model 624/650 Electric / International (Export)
- Page 23 Maintenance Notes:...
- Page 24 Nieco Corporation • 15 Guittard Rd. • Burlingame, CA • 94010 • (650) 697-7335 • Fax (650) 697-3014 Reorder # 9999-99114 7/01 www.nieco.com • e-mail: nieco@nieco.com © 2001 Nieco Corporation Printed in the USA TN...
Need help?
Do you have a question about the 824E and is the answer not in the manual?
Questions and answers