Summary of Contents for Nieco BroilVection JF91 Gas
Page 1
Broiler area must be kept free of combustible materials, and the flow of combustion and ventilation air must not be obstructed. Operating personnel must not perform any maintenance or repair functions. Contact your Nieco Authorized Dealer. IMPORTANT: RETAIN THIS MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE...
This manual provides the safety, installation and operating procedures for the Nieco Automatic Broiler Model JF91. We recommend that all information contained in this manual be read prior to installing and operating the broiler.
Authorized Nieco Distributors and Service Agencies will void the warranty and may significantly alter the performance of your broiler. The use of non-Nieco parts is capable of affecting these criteria, and may affect broiler performance, parts longevity and food safety. Your local Authorized Nieco Distributor and Service Agent has been factory trained and has a complete supply of parts for your Nieco Automatic Broiler.
Page 5
Distributor for adjustment or repair. • Use only genuine Nieco replacement parts for your broiler. Failure to do so will void the warranty and may significantly alter the performance of your broiler. The use of non-Nieco parts is capable of affecting these criteria, and may affect broiler performance, parts longevity and food safety.
For easy movement of the appliance, the connector should be installed with a "lazy" loop for minimum tension. note: Gas appliances should be disconnected prior to maximum movement. (Minimal movement is possible to connect hose.) Nieco Corporation - Model JF91G...
Disconnect power before servicing. b.10 Pre-operation Check Be sure that all parts are installed in the proper location: Ventilation is turned on Broiler is plugged in Gas line is connected Nieco Corporation - Model JF91G...
3. Main on/off switch - Turns the power to the broiler on and off. 4. Temperature Control (P/N 19076) - Helps keep the broiler temperature stable when the broiler is under heavy load. 5. Multi product control - Lets you have multiple product recipes preprogrammed. Nieco Corporation - Model JF91G...
Page 10
3. ADJUSTMENT BUTTONS - Use to adjust product cook times, element settings and product names. 4. SELECTION INDICATOR LIGHT - Lights up to show which button is selected. Multi-speed control P/N 15161-B Nieco Corporation - Model JF91G...
If this still doesn’t light the broiler, see the MANUAL IGNITION instructions. 1. Turn the MaIn PoWeR sWITCH on. 2. Allow broiler to heat for 45 minutes before cooking. Nieco Corporation - Model JF91G...
Your Nieco Automatic Broiler is designed to automatically stop gas flow to the broiler in the event of power failure, gas pressure loss or any other related incident. No attempt to operate this appliance should be made in the event of a power failure.
Step 2: Turn the broiler on and set the set point (bottom Number) to 1000. Let the broiler warm up for 25 minutes. DO NOT COOK DURING THIS TIME. After the 25 minutes is up, use the arrows to put the set point to the actual temperature. The bottom number is the set temperature and the top number is the actual temperature. Nieco Corporation - Model JF91G...
Page 14
(10 character limit). Press and hold the PRODUCT SELECTION BUT- TON for 5 seconds to save the changes and return to normal operation. Nieco Corporation - Model JF91G...
The name of the part to be cleaned. The location of the part. When to clean the part. The tools needed to clean the part Picture of the part to be removed and cleaned. How to remove and clean the parts. Nieco Corporation - Model JF91G...
Page 16
Meat Guide Clean: Every 4 hours Feed End Tools Scrub Pad 3-Compartment Sink Instructions 1. Lift the meat guide up and off the feeder. 2. Wash, rinse, and sanitize in the 3-compartment sink. Nieco Corporation - Model JF91G...
Page 17
3. Wash, rinse, and sanitize in the 3-compartment sink. DO NOT lift the feeder base by the feeder bar or the chains. This will damage the feeder base. REASSEMBLY: Pull the release pin and place feeder base in position. Nieco Corporation - Model JF91G...
Page 18
Feed End Heat Shield Clean: Daily Feed End Tools Scrub Pad 3-Compartment Sink Instructions 1. Lift and remove. 2. Wash, rinse, and sanitize in the 3-compartment sink. REASSEMBLY: Hang feed end heat shield on brackets. Nieco Corporation - Model JF91G...
Page 19
Heat Resistant Gloves Degreaser 3-Compartment Sink Instructions 1. Slide warming pan shield out. 2. Take to sink area and spray with degreaser. 3. Wash with a scrub pad, rinse, and sanitize in the 3-compartment sink. Nieco Corporation - Model JF91G...
Page 20
Scrub Pad Heat Resistant Gloves Degreaser 3-Compartment Sink Instructions 1. Slide crumb tray out. 2. Take to sink area and spray with degreaser. 3. Wash with a scrub pad, rinse, and sanitize in the 3-compartment sink. Nieco Corporation - Model JF91G...
Page 21
Discharge End Tools Scrub Pad Heat Resistant Gloves Degreaser 3-Compartment Sink Instructions 1. Lift up and off. 2. Take to sink area and spray with degreaser. 3. Wash, rinse, and sanitize in the 3-compartment sink. Nieco Corporation - Model JF91G...
Page 22
Make sure stripper blade is cool before putting in water or it may warp. 2. Take to sink area and spray with degreaser. 3. Wash with a scrub pad, rinse, and sanitize in the 3-compartment sink. REASSEMBLY: Hang stripper blade on brackets. Nieco Corporation - Model JF91G...
Page 23
2. Take to sink area and spray with degreaser. 3. Wash with a scrub pad, rinse, and sanitize in the 3-compartment sink. REASSEMBLY: Be sure grease trough is pushed all the way into the broiler. Nieco Corporation - Model JF91G...
Page 24
2. SOAK IN WARM WATER FOR 1 HOUR. RINSE WITH WATER ONLY. NEVER USE ANY CHEMICALS ON THE CATALYST. 3. Lay flat to drain water and let air dry overnight. CAUTION: Extremely Hot 4. Make sure Incendalyst™ is dry before putting back on broiler. Nieco Corporation - Model JF91G...
Page 25
EXTREMELY HOT! Be careful not to burn yourself. 1. Lift upper heat shield up and off. 2. Take to sink area and spray with degreaser. CAUTION: Extremely Hot 3. Wash with a scrub pad, rinse, and sanitize in the 3-compartment sink. Nieco Corporation - Model JF91G...
Page 26
Be sure that both air box assemblies are installed and sit flush on their brackets. Main Burner Orifices Clean: Monthly Side Tools Small Orifice Brush Instructions 1. Use a small brush to clean the main burner orifices Nieco Corporation - Model JF91G...
Page 27
2. Remove the ceramic boot from the back of the flame sensor. 3. Loosen the wing nut holding the flame sensor in place. 4. Remove the flame sensor and clean the metal tip with a DRY, clean scrub pad. Nieco Corporation - Model JF91G...
Page 28
1. Scrape each shaft of both belts on the discharge end with the wide end of the shaft cleaning tool. The tool is located on the clip on the discharge end of the broiler. 2. Wipe shaft cleaning tool with a towel. Nieco Corporation - Model JF91G...
Check cookout temperature (undercooking). CooKInG PRobleMs Burgers under or over cooked. Adjust conveyor belt speed. Clean burners and orifices. Excessive flaming in broiler. Clean the catalyst if equipped. Check the hood for proper operation. Check product for overcooking. Nieco Corporation - Model JF91G...
CaUTIon Do not operate the broiler at gas pressures other than those stated here. Doing so will affect the opera- tion of your broiler. Nieco Corporation - Model JF91G...
Need help?
Do you have a question about the BroilVection JF91 Gas and is the answer not in the manual?
Questions and answers