[Rgb In] - Panasonic PT-DX820 Operating Instructions Manual

6) Press qw to switch the item.
f The items will switch each time you press the button.
[ENABLE]
[DISABLE]
Note
f Backup function is enabled only when the [BACKUP INPUT MODE] is [ON] and the same signal is input to the <DVI-D IN> terminal and
<HDMI IN> terminal.
f To switch to the backup input signal using the backup function, make sure that the following three conditions are satisfied to be ready to use
the function.
g Set [BACKUP INPUT MODE] to [ON].
g Input the same signal to the primary and secondary inputs.
g Display the image of the primary input.
f If the input is switched to other than the primary or secondary input while the backup function is ready for use, the state of readiness to use
the backup function is canceled. To switch to the backup input signal using the backup function again, switch to the primary input.
f When [BACKUP INPUT MODE] is [ON], [BACKUP INPUT STATUS] is displayed both in the input guide (x page 104) and on the
[STATUS] screen (x pages 67, 122).
When switching to the backup input signal is possible using the backup function, [ACTIVE] is displayed in [BACKUP INPUT STATUS]. When
it is not possible, [INACTIVE] is displayed instead.
When [BACKUP INPUT STATUS] is [ACTIVE] while the image of the primary input is displayed, the secondary input becomes the backup
input.
When [BACKUP INPUT STATUS] is [ACTIVE] while the image of the secondary input is displayed, the primary input becomes the backup
input.
f If the inputs of DVI-D and HDMI are switched while [BACKUP INPUT MODE] is set to [ON] and switching to the backup input signal is
possible, the input is switched seamlessly.
f When [AUTOMATIC SWITCHING] is set to [ENABLE] and [BACKUP INPUT STATUS] is [ACTIVE], the signal is switched to the backup
input automatically if the input signal is disrupted.
f When [AUTOMATIC SWITCHING] is set to [ENABLE] and the signal is automatically switched to the backup input due to disruption of the
input signal, [BACKUP INPUT STATUS] changes to [INACTIVE]. In this case, switching to the backup input signal is not possible until the
original input signal is restored. If the signal is automatically switched to the backup input, switching to the backup input signal becomes
possible when the original input signal is restored. In this case, the current input is retained.
f [BACKUP INPUT SETTING] cannot be set during P IN P. The backup operation is not performed either.

[RGB IN]

Set to match the signal to input to the <RGB 1 IN> terminal.
Setting [RGB1 INPUT SETTING]
1) Press as to select [RGB IN].
2) Press the <ENTER> button.
f The [RGB IN] screen is displayed.
3) Press as to select [RGB1 INPUT SETTING].
4) Press qw to switch the item.
f The items will switch each time you press the button.
[RGB/YP P ]
B R
[VIDEO]
[Y/C]
Note
f When [REMOTE CONTROL] is set to [USER] and [VIDEO BUTTON] of [INPUT SELECT BUTTON] is set to other than [DISABLE] from the
[SECURITY] menu → [CONTROL DEVICE SETUP] (x page 135), pressing the <VIDEO> button on the remote control switches [RGB1
INPUT SETTING] to [VIDEO] or [Y/C].
Switching the slice level of an input sync signal
1) Press as to select [RGB IN].
2) Press the <ENTER> button.
f The [RGB IN] screen is displayed.
98 - ENGLISH
Chapter 4 Settings — [DISPLAY OPTION] menu
Switches to the secondary input automatically when the input signal for primary input is disrupted.
Disables the automatic input switching function.
Select this item when an RGB signal or YC
terminal.
Select this item when a video signal is being input to the <RGB 1 IN> (<R/P
Select this item when a luminance signal and color signal are being input to the <RGB 1 IN> (<G/Y>,
<B/P /C>) terminal.
B
C /YP P signal is being input to the <RGB 1 IN>
B R B R
/VIDEO>) terminal.
R