1. Manuals
  2. Brands
  3. AGFEO Manuals
  4. Telephone
  5. DECT-S0-Base plus
  6. Installation manual

AGFEO DECT-S0-Base plus Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
AGFEO DECT
Installation Manual
DECT-S0-Base plus
Bedienung
1

Advertisement

Table of Contents
loading

Related Manuals for AGFEO DECT-S0-Base plus

Summary of Contents for AGFEO DECT-S0-Base plus

  • Page 1 AGFEO DECT Installation Manual DECT-S0-Base plus Bedienung...

  • Page 2: About This Manual

    User Instructions The AGFEO DECT-S0-Base plus is for use with the following AGFEO Telephone Systems from Firmware 6.0: AS 1x, AS 2x : One DECT-S0-Base can be connected to the system.

  • Page 3: Table Of Contents

    Up to eight AGFEO DECT System Phones or other GAP compliant DECT Handsets may be connected to the DECT-S0-Base plus. However, only four of these can be used at the same time. The bases can be installed of up to 150 metres away from the telephone system. In case of a point to point connection the base may be of up to 800 metres away from the telephone system.

  • Page 4: Box Content

    User instruction in PDF-Format can be found at our Homepage www.agfeo.com Location Please install the DECT-S0-Base plus in a dry room free of any explosive materials. Do not install the unit near air conditioners, radiators, apparatus with high interference, in direct sunlight, high dusty environments or where the unit could be subjected to water or chemical spills.

  • Page 5: Dect-S0-Base Plus Connections

    Supply LED’s of the DECT-S0-Base plus LED 1 LED 2 LED 3 LED 4 LED 5 The AGFEO DECT-S0-Base plus has 5 LED’s which will give information of the operational status. LED 1: First B channel of the first S0 is busy.

  • Page 6: Connecting The Dect-S0-Base Plus To The Telephone System

    RFPI number and to which S0-Bus the DECT-S0-Base plus has been connected. The RFPI (Radio Fixed Part Identity) is a worldwide used standard and a uniqe recognisable number which identifies the DECT-S0-Base plus. This number can also be found on the label of the DECT-S0-Base plus.
  • Page 7 Extension numbers, either for handsets which are already registered or will be registered to the base can be allocated in the section: „Extensions / Devices: DECT“. The entry in the column „Phone Type“ will be allocated automatically by the telephone system. (ie AGFEO DECT 30 or DECT GAP Phone).

  • Page 8: Delete Registration Of Dect-S0-Base Plus From Telephone System

    Delete Registration of DECT-S0-Base plus from Telephone System To delete a DECT-S0-Base plus from the telephone system go to the section „PBX / DECT S0 Base“and click the „Delete“ button. All associated entries such as extension number(s) and name of base will also be deleted.

  • Page 9: Register Handsets To The Dect-S0-Base Plus

    Your DECT Telephone may be registered to a pre-programmed location in the DECT-S0-Base plus. It would make sense to assign names to the 8 locations within the DECT-S0-Base plus via TK-Suite as this will ensure that this location will be definitely allocated to the registering handset.

  • Page 10: Deregister Handsets From The Dect-S0-Base Plus

    DECT-S0-Base plus Deregister Handsets from the DECT- ST 25 ST 30 / ST 40 DECT 30 S0-Base plus AQ9L Initiate programming mode. Use „next“ or the arrow button to select & & the phone which is going to be deregistered.

  • Page 11: Conformity Declaration

    DECT-S0-Base plus Conformity Declaration...
  • Page 12 Ident no. 1101532 Subject to change without notice. No liability AGFEO GmbH & Co. KG can be accepted for errors contained in this Gaswerkstr. 8 document.

Table of Contents