1. Manuals
  2. Brands
  3. Infinity Manuals
  4. Indoor Fireplace
  5. 660 PC
  6. Owner's manual

Infinity 660 PC Owner's Manual

Infinity 660 pc gas fire owner manual
Hide thumbs
Table of Contents

Advertisement

Quick Links

OWNER MANUAL
INCLUDES
USER INSTRUCTION
&
INSTALLATION & MAINTENANCE
INSTRUCTIONS
Please read these instructions carefully before you start installing or using this
appliance
Keep this booklet handy for future reference
This appliance is
For use in Great Britain or
IRELAND only
FROM INFINITY FIRES
Charlton & Jenrick Ltd
TELFORD
SHROPSHIRE
TF3 3AR

Advertisement

Table of Contents
loading

Related Manuals for Infinity 660 PC

Summary of Contents for Infinity 660 PC

  • Page 1 Please read these instructions carefully before you start installing or using this appliance Keep this booklet handy for future reference This appliance is For use in Great Britain or IRELAND only FROM INFINITY FIRES Charlton & Jenrick Ltd TELFORD SHROPSHIRE TF3 3AR...

  • Page 2: Table Of Contents

    PCInstructions CONTENTS PAGE USERS INSTRUCTIONS SECTION ONE Introduction Consumer Protection Information Heath & Safety Notice Introduction Important Information SECTION TWO Operating Appliance Lighting the Appliance Replacing Hand Set Battery Replacing Appliance Battery SECTION THREE Cleaning Cleaning Trim and Fret or Fascia Cleaning Black Painted Surfaces Cleaning Pilot Assembly Cleaning Glass panel...

  • Page 3: Users Instructions

    ‘hazardous waste and should be disposed of at a site licensed for the disposal of industrial waste. INTRODUCTION  The 660 PC as been designed and tested to the requirements of EN 613 and is suitable for use in GB (Great Britain) and IE (Ireland). ...

  • Page 4: Important Information

    SECTION ONE Introduction Continued The 660 PC is battery operated; therefore no mains electrical supply is required. Power to the appliance is provided by 6 high power alkaline 1.5V batteries (“C” size) (a spare set of 6 “C” batteries is supplied with the appliance An audible repeated bleep warning indicates that the appliance batteries need changing or charging (if rechargeable batteries have been used).

  • Page 5: Section Two

    660 PC Users Instructions SECTION ONE Introduction Continued  Care must be taken to prevent any damage being caused to surrounding soft furnishing or decoration; e.g. many embossed vinyl wall coverings may become discoloured if placed too close to the appliance. Combustible material i.e. wall panelling or wallpaper must be removed from behind the fire and fire fascia.
  • Page 6 660 PC Users Instructions SECTION TWO Operating the Appliance Continued The icon “PILOT” will appear on the LCD display. As soon as the actual room temperature falls below the SET room temperature, the system will move from standby to the high flame level. From this point it will proceed again the modulation process.
  • Page 7 660 PC Users Instructions SECTION TWO Operating the Appliance Continued LOW BATTERY INDICATION (APPLIANCE) If you hear a repeated ‘bleep’ sound come from the appliance this indicates the appliance battery pack is low and should be changed. If this is ignored the system will go into a lock out mode, which will not allow the appliance to be used until a new set of batteries are loaded.

  • Page 8: Glass Cleaning

    Note: - Take care when cleaning in this area so as not to damage the pilot assembly. GLASS CLEANING From time to time it will be necessary to clean the glass panel of your 660 PC fire. We recommend you use a Ceramic hob cleaner these are available for all leading super markets: - i.e. ASDA, TESCO, SAINSBURY’S Etc.

  • Page 9: Section Four

    660 PC Users Instructions SECTIONTHREE Cleaning Continued REMOVING GLASS PANEL  Remove the five 7mm nuts holding the front glass panel retaining bracket and slide the bracket clear of the studs.  Lift the glass panel out of the bottom retaining bracket.
  • Page 10 660 PC Users Instructions SECTION FOUR Fuel Bed Cleaning and Layout Continued Place three of the log shapes on top of the air tray touching the glass back liner as shown. Place three shapes shown within the burner top plate and air tray as shown.
  • Page 11 660 PC Users Instructions SECTION FOUR Fuel Bed Cleaning and Layout Continued Bridge two of the shape as shown. Bridge two of the shapes as shown. Bridge two of the shapes as shown. LT6159 issue 7(06/13)

  • Page 12: Section Five

    660 PC Users Instructions SECTION FOUR Fuel Bed Cleaning and Layout Continued  Bridge two of the shapes as shown. SECTION FIVE Appliance Data NATURAL GAS Gas Type: CATEGORY I 2 H Gas Pressure: 20 mbar +/- 1.0mbar Pressure Test Point Location:...

  • Page 13: Section Six

    660 PC Installation Instructions SECTION SIX Regulations and Warnings  This appliance must only be installed in Great Britain or Ireland.  The appliance is suitable for use on natural gas only.  GB (Great Britain) This fire does not normally require purpose build ventilation.

  • Page 14: Section Seven

    660 PC Installation Instructions SECTION SEVEN Siting the Appliance MUST Please note on 125mm diameter flue system the Spigot restrictor plate be removed Class 1 Conventional Flue. The chimney must have a minimum effective height of at least 3 metres. Any permanent flue restriction or variable dampers are to be removed or locked fully open.

  • Page 15: Connecting The Gas Supply

    660 PC Installation Instructions SECTION EIGHT To Install the Appliance FITTING THE CLOSURE PLATE The front of the fireplace should be flat over an area sufficient to ensure a good seal with the closure plate. The flat surface should extend for a height equal to that of the closure plate plus 20mm and for a width equal to that of the closure plate plus 40mm.

  • Page 16: Checking Gas Soundness

    660 PC Installation Instructions SECTION NINE Checking Operation of Fire CHECKING GAS SOUNDNESS  Turn on the gas supply to the appliance and check for soundness in accordance with current codes of practice.  Turn off the gas supply at the external Isolation valve.
  • Page 17 660 PC Installation Instructions SECTION NINE Checking Operation of Fire CHECKING FOR COMBUSTION PRODUCTS CLEARENCE IMPORTANT:-The smoke test must be carried out with the fire starting from cold.  Light the fire and leave at maximum input.  Close all the doors and windows.

  • Page 18: Maintenance Instructions

    660 PC Maintenance Instructions SECTION TEN Maintenance GENERAL  Servicing should be carried out annually by a competent person such as a GAS SAFE-registered person in accordance with the relevant regulations, to ensure the safe and correct operation of the appliance.

  • Page 19: Replacement Of Oxy-Pilot Assembly

    660 PC Maintenance Instructions SECTION TEN Maintenance Continued REPLACEMENT OF OXY-PILOT ASSEMBLY NOTE: If the pilot assembly is replaced it must be replaced by an identical unit from the same manufacturer and replaced as a complete unit.  Follow the burner tray removal sequence.
  • Page 20 7. The appliance has not been subjected to misuse or accident or been modified or repaired by any person other than the authorised employee or authorised representative of Charlton and Jenrick Ltd. 8. The registration form must be returned within 3 months of purchase. INFINITY HELPDESK NUMBER 0845 5195991 LT6159 issue 7(06/13)
  • Page 21 For future reference we suggest you record the following details here, and keep the receipt as proof of purchase. This information may be asked for when you contact the helpdesk. Model: Infinity 660 PC Serial No. This information can be found on the label attached to the packaging and on the data badge, which is located on the left hand side of the base of the appliance behind trim.

  • Page 22: Lt6159 Issue

    Engineer Name Gas Safe Registration No. We may introduce modifications to products from time to time, and consequently the details given in this booklet are subject to alteration without notice. Infinity Fires Charlton & Jenrick Ltd Telford Shropshire TF3 3AR...
  • Page 23 Post Code TELEPHONE No. PRODUCT DETAILS Model: INFINITY 660 PC Serial No. Date of Purchase This information can be found on the label attached to the packaging and on the data badge, which is located on the left hand side of the base of the appliance behind trim.
  • Page 24 Prefix Product Serial No (MT) A-0334 Prefix Label (Ng) Burner Tray / Box Assembly Back spigot Fitted / Restrictor Label Air Tray (Part No 6081) Glass Panels 1 x rear 2 x side 1 x Front Log Fuel Bed (6114) AAA Battery (3) Remote Control Hand Set Handset Holder (5910)

Table of Contents