Page 2
Thank you for purchasing this product. FLIR/Digimerge is committed to providing our customers with a high quality, reliable security solution. This manual refers to the following models: • DPB24TLX For more information on this product and accessory products, please visit us at: www.digimerge.com...
Important Safeguards In addition to the careful attention devoted to quality standards in the manufacturing process of your video product, safety is a major factor in the design of every instrument. However, safety is your responsibility too. This sheet lists important information that will help to assure your enjoyment and proper use of the video product and accessory equipment.
Service 13. Servicing - Do not attempt to service this video 19. Cleaning - Unplug the video product from the wall equipment yourself as opening or removing covers outlet before cleaning. Do not use liquid cleaners or may expose you to dangerous voltage or other aerosol cleaners.
Page 5
General Precautions 1. All warnings and instructions in this manual should be followed. 2. Remove the plug from the outlet before cleaning. Do not use liquid aerosol detergents. Use a water dampened cloth for cleaning. 3. Keep enough space around the unit for ventilation. Slots and openings in the storage cabinet should not be blocked.
Page 6
Features • 1/3" Sony EX-View™ II 960H with Effio DSP/700+ TVL • Next Generation Polaris Vision3 for Superior Low Light Viewing • Smart-IR Night Vision (135ft/41m) • 2.8-12mm Auto Iris D/N Long-Range Varifocal Lens • True Day Night with ICR mechanism (TDN) •...
Getting Started 1. GETTING STARTED The system comes with the following components: • 1 x Camera • 1 x Mounting Screw Kit Mounting Screw Kit: • 1 x Allen Key • 3x mounting screws (PA4 30mm) • 1 x BNC Test Cable •...
Camera Installation 2. CAMERA INSTALLATION Make sure to follow the correct polarity if connecting the camera to DC power. Polarity is marked on the power connector. 1. Use the included mounting template to mark mounting points for the camera. NOTE: If mounting the Mounting...
Page 11
Camera Installation • A. Insert the included BNC test cable into the video test cable terminals and connect to a test monitor to check the camera viewing angle. • B. For details on adjusting the OSD menu, see “3. Configuring OSD Menus” on page 5.
Page 12
Camera Installation 5. To adjust the camera’s zoom and focus: • Open the service compartment near the camera lens by loosening the screws (x2) with the included allen key. • Twist the zoom and focus knobs counterclockwise to unlock. Move the knobs left or right to adjust the zoom and focus.
Configuring OSD Menus 3. CONFIGURING OSD MENUS Use the OSD controls, located inside the service compartment, to configure the camera’s OSD menus. Press the middle button to open the OSD menu. RIGHT OSD Controls: • Middle: Open Menu; enter LEFT button DOWN •...
Configuring OSD Menus 3.3 Exposure Select AUTO or MANUAL exposure. 3.3.1 Auto High Luminance • Mode: Select AE+AUTO IRIS or ME+AUTO IRIS. • Brightness: Brightness level of operating mode set above. Default setting is 32. Low Luminance • Mode: Select AGC, DSS, AGC>DSS, AGC>DSS>AGC, or OFF. NOTE: Settings available only when AUTO is selected in OTHERS>LENS.
Configuring OSD Menus 3.3.2 Manual • Mode: Select the manual exposure mode: SHUT or DSS. • Shut: When Mode is set to SHUT, select the shutter speed in x / second: 1/60, 1/100, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000. Default setting is 1/60....
Configuring OSD Menus • Sharpness: Select screen sharpness from 0~15. • Hue: Adjust the hue value from 0~100. • R-Gain: Adjust red gain from 0~255. • B-Gain: Adjust blue gain from 0~255. • Defog: Select HIGH, MID, or LOW to select the level for Defog function or OFF to disable.
Configuring OSD Menus 3.5 White Bal Select one of the following White Balance modes: ATW, PUSH, USER1, USER2, ANTI CR, or PUSH LOCK. 3.5.1 ATW (Auto Trace White Balance) • Speed: Specifies the AE control for ATW between 0~255. • Delay Cnt: Sets the delay time for ATW changes between 0~255. •...
Configuring OSD Menus 3.5.3 User1/2 User defined Blue and Red gain adjustment. • B-Gain: Adjust Blue gain for white balance between 0~255. • R-Gain: Adjust Red gain for white balance between 0~255. 3.5.4 Anti-CR Activates color rolling suppression. 3.5.5 Push Lock Press down on joystick to set current scene as the white balance level.
Configuring OSD Menus • Level: When Mode is set to D-WDR, select the Digital Wide Dynamic Range level: LOW, MIDLOW, MID, MIDHIGH, or HIGH. • HLC: Select ON to enable High Light Compensation, select OFF to disable, or select AUTO for automatic selection. •...
Configuring OSD Menus 3.8 Day/Night Day/Night mode can be set to the following options: • COLOR: Color image. • BW: Black and white image. • EXT: CdS light sensor activates Day/Night operation. • AUTO: Camera sensor selects Day/Night mode, based on lighting conditions.
Configuring OSD Menus • Day-Night: Select threshold for Night status from Day status between 0~255. • Night-Day: Select threshold for Day status from Night status between 0~255. 3.8.2 BW Setup Allows additional Smart IR settings to be enabled. • Smart IR: Select ON to enable Smart IR; press the middle button to configure Smart IR settings.
Configuring OSD Menus 3.9 Privacy Configure up to 15 privacy areas that will not be displayed on the monitor. • Area Sel: Select the area you would like to configure. • Mode: Select ON to enable the selected privacy area or OFF. When a privacy area is enabled, you may configure the settings below.
Configuring OSD Menus 3.10 Motion Detect Configure Motion Detection settings for the camera. The motion detection areas of the screen are broken into 24 x 16 rectangular blocks. Use MONITOR AREA to configure always-on motion alert areas on the screen. TIP: Motion detection settings are usually set independently on the DVR, which allows for more advanced customization options.
Configuring OSD Menus • Mode: Select ON to enable the selected monitor area or OFF. • Top: Select the top position of the area. • Bottom: Select the bottom position of the area. • Left: Select the left position of the area. •...
Configuring OSD Menus • Mode: Select the iris control mode: AUTO, OPEN, or CLOSE. • Speed: Select the iris convergence speed between 0~255. 3.11.3 Sync Camera uses internal sync (INT) when camera is connected to DC power. Line Lock (LL) is used when camera is connected to AC power. If you notice color rolling when the camera is connected to AC power: 1.
Configuring OSD Menus • Use POS to change the title position. 3. When finished, select RETURN and press the middle button to save the camera title. 3.11.5 WPC (Advanced Function; Not for Normal Use) The WPC (White Pixel Compensation) features is used to correct the CCD if dead pixels are visible.
Configuring OSD Menus 3.11.7 Camera Reset (Factory Default) Select CAMERA RESET and press the middle button to reset the camera to factory default settings. 3.12 Exit / Save All • Exit: Select EXIT and press the middle button to exit the OSD menu. This will keep any changes only until camera is powered off.
Operating Temperature –40~122°F / –40~50°C IP Rating IP66 Weight 0.8kg/1.7lbs Because our products are subject to continuous improvement, Digimerge Technologies Inc, a FLIR Company, reserves the right to modify product design and specifications without notice and without incurring any obligation. E&O.E.
Troubleshooting 6. TROUBLESHOOTING Follow the steps below if you are experiencing trouble with your camera. Contact Digimerge Technical Support if the issue persists. Nothing appears on the screen: • Check that the power cable is connected properly and that the voltage is correct.
Page 34
Need Help? Please make sure to visit our website www.digimerge.com to receive product updates and information. 3 Easy Ways To Contact Us Online: P ro d u c t s upp or t i s a v a i l a b l e 2 4 / 7 i n c l ud i n g p r od u c t in fo r m a ti on , u se r m a nu a l s , qu i c k s t a rt up g u i d e s an d FA Q’s w w w.d ig i m e rg e .c om By Email:...