Table of Contents
Advertisement
READ AND SAVE THESE INSTRUCTIONS
HIGHPOINTE
™
Ceiling Fan
Owner's Manual
Model Numbers
CF205GES01
CF205BS01
Golden Espresso with
Brushed Nickel Finish with
Sandstone Glass and
Opal Matte Glass and
Chocolate Blades
Dark Mahogany Blades
22.1
Net Weight:
Lbs.
Part No. F40BP73750001
Form No. BP7375-1
U.L. Model No.: CF205
Advertisement
Table of Contents
Related Manuals for Emerson HIGHPOINTE CF205BS01
Summary of Contents for Emerson HIGHPOINTE CF205BS01
-
Page 1: Ceiling Fan
READ AND SAVE THESE INSTRUCTIONS HIGHPOINTE ™ Ceiling Fan Owner's Manual Model Numbers CF205GES01 CF205BS01 Golden Espresso with Brushed Nickel Finish with Sandstone Glass and Opal Matte Glass and Chocolate Blades Dark Mahogany Blades 22.1 Net Weight: Lbs. Part No. F40BP73750001 Form No. -
Page 2: Safety Instructions
WARNING: This product is designed to use only those parts supplied with this product and/or any accessories designated specifically for use with this product by Emerson Electric Co. Substitution of parts or accessories not designated for use with this product by Emerson Electric Co. could result in personal injury or property damage. -
Page 3: Unpacking Instructions
If any parts are missing, contact parts or accessories not designated for your local retailer or catalog outlet for use with this product by Emerson Electric replacement before proceeding. Co. could result in personal injury or property damage. -
Page 4: Electrical Requirements
General at the main fuse box before wiring. All Your Emerson ceiling fan comes supplied wiring must be in accordance with with a Fan/Light Remote Control which National and Local codes and the ceil-... - Page 5 2. Remove and discard the three shipping 4. Connect the white wire from the light kit retainers securing the motor hub in the plate to the white wire in the fan motor/ motor housing. housing assembly (Figure 6). Connect the black wire from the light kit plate to NOTE: Take care not to scratch the fan the black wire in the fan motor/housing housing when installing the blade...
- Page 6 6. Carefully remove the fan assembly WARNING from the lower foam pad. Turn the fan assembly over and position it on the It is critical that the clevis pin in the lower foam pad with the light kit plate motor coupling is properly installed resting on the pad so that the top of and the setscrews securely tight- ened.
- Page 7 11. Make sure the grommets are properly 13. Slide the rod support assembly up installed in the rod support assembly. the downrod until the threaded holes in Then position the three screws in the the rod support align with the rod support toward the top, and slide holes in the decorative rod assemblies the rod support over the downrod...
-
Page 8: Your Ceiling Fan How To Hang
How to Hang 15. Place the ceiling cover over the down- rod. Then reinstall the hanger ball Your Ceiling Fan (Figure 13) on the downrod as follows. Route the three 80” motor leads WARNING through the hanger ball and slide the The fan must be hung with at least 7' hanger ball over the downrod. -
Page 9: How To Wire Your Ceiling Fan
How to Wire WARNING Your Ceiling Fan Hanger bracket must seat firmly If you feel that you do not have enough against outlet box. If the outlet box is electrical wiring knowledge or experi- recessed, remove wall board until ence, have your fan installed by a bracket contacts box. - Page 10 d. Securely connect the fan motor white WARNING wire to the receiver white (TO MOTOR N) wire. Check to see that all connections are tight, including ground, and that no e. Securely connect the fan motor black bare wire is visible at the wire con- wire to the receiver red (TO MOTOR L) nectors, except for the ground wire.
- Page 11 3. Push the wires and connectors up into CAUTION: To avoid risks of burns or other injury, assure power is off before the outlet box while inserting the receiv- attempting to install or replace the er fully into the hanger bracket. Position halogen bulbs.
- Page 12 How to Disassemble Your Light Kit for Cover Plate Assembly Only WARNING Turning off wall switch is not suffi- cient. To avoid possible electrical shock, be sure electricity is turned CUT LIGHT off at the main fuse box before SOCKET WIRES wiring.
-
Page 13: Remote Control Procedures
2. Remove the connector from the battery Preset Memory Feature compartment and install two AAA alka- Your Emerson receiver is equipped with a line batteries. preset memory feature. If the AC supply to the receiver is powered through a wall... -
Page 14: Operation Of Remote Control
1. To set the desired fan speed, hold the Setting Operating FAN ( ) button down, then press one Frequency of of the four buttons ( . , .. , ... , ..) to oper- Transmitter ate your fan from low to high speeds. Your remote control transmitter has code 2. -
Page 15: Maintenance
Short Range designated specifically for use with • If the remote control operates the this product by Emerson Electric Co. fan when close to it, but does Substitution of parts or accessories not operate it at a distance of... -
Page 16: Troubleshooting
WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER BEFORE TROUBLE SHOOTING YOUR FAN. Trouble Shooting TROUBLE PROBABLE CAUSE SUGGESTED REMEDY 1. Fuse or circuit breaker 1. Check main and branch 1. Fan will not blown. -
Page 17: Instruction To The User
INSTRUCTION TO THE USER (if device contains a digital device) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reason- able protection against harmful interference in a residential installation. -
Page 18: Repair Parts
Repair Parts U.L. Model No.: CF205... -
Page 19: How To Order Repair Parts
Repair Parts Listing Part Numbers Model No. Model No. Description CF205BS00 CF205GES00 Hanger Pack, Consisting of: 761655-74 761655-39 Hanger Bracket — — Hanger Ball — — 12” Downrod — — Parts Bag, Containing: 763596 763596-1 Wire Connector (7) — — Threaded Stud, 8-32 x 1-1/4”... -
Page 20: Limited Warranty
You will be responsible for all insurance, freight or other transportation charges to our factory or authorized service center. Your Emerson Air Comfort Ceiling Fan should be properly packed to avoid damage in transit since we will not be responsible for any such damage.